Tony,

The adjustment of R622 is in LBI-30109J, at the bottom of page 5.  Go here:
<www.repeater-builder.com/ge/lbi-library/lbi-30109j.pdf>

R622 adjusts the noise amplitude controlling the squelch circuit.  Here's
the quote from LBI-30109J:  "Squelch adjust control R622 (if present) is
preset at the factory.  If further adjustment is required, adjust R622 on
the IFAS board for best squelch operation.  NOTE:  Maximum squelch decreases
with increasing resistance."  Revision B also changed the PC board, so it is
likely that your radio has R622 on the older board, hence the Rev A marking.

73, Eric Lemmon WB6FLY


-----Original Message-----
From: [email protected]
[mailto:[email protected]] On Behalf Of Tony Alviar (Home)
Sent: Saturday, January 03, 2009 8:09 AM
To: [email protected]
Subject: RE: [Repeater-Builder] mastr II question. . . IFAS
Board--correction

See omission below 

-----Original Message-----
From: Tony Alviar (Home) [mailto:[email protected]
<mailto:talviar%40worldnet.att.net> ] 
Sent: Saturday, January 03, 2009 11:07 AM
To: '[email protected]
<mailto:%27Repeater-Builder%40yahoogroups.com> '
Subject: RE: [Repeater-Builder] mastr II question. . . IFAS Board

With that said. . . Here is my main problem and question. . . 

A # of years ago local radio club purchased 3 complete repeater stations. .
. Have one converted working fine with no known issues other than it
doesn't get used as much as I'd like folks to use it ;)

The other two stations one had issues on fire up, other appeared functional
(best as could be told since the units didn't have TX/RX elements in them
and couldn't bench on original freq and had to tune exciter/receiver to high
band elements I have.

Have since rerocked onto a ham freq 147.045TX/147.645RX and have been
experiencing many problems since. (After looking over everything with a
local tech who spends his former life working on Lowband and UHF Mastr
II's--20+ years) stated to check IF Alignment (weird things happening when
audio hit certain levels and such which matched a lot in the GE IF alignment
docs I found on Repeater Builder stating IF Alignment issues)

After looking at other working base with the IF alignment test setup
(o'scope looking at wave forms) it was apparent that this base was
definitely out of alignment.

Still having some issues where I can't get the audio level up to the 1 V RMS
@ P904-11 and P904-17 as outlined in the alignment docs. (I can get 1V RMS
but wave form coming out of there into repeater controller is clipping as it
is over driven. . . When set for not clipping with 1KC tone @ 3KC deviation
audio level is about .6-.7 V RMS)

Main reason for needing schematic is to follow and see if any thingis weak
in audio path thru everything and couldn't follow audio thru IFAS board as
schematics didn't match up.

My next question is what does R622 on the board (IFAS 19D432667G1 Rev A) do?
Can't find it in text write up or details on RX Alignment. . . 

--OMIT THIS SENTENCE was looking at wrong parts listing-Now for interesting
thing schematic lists R622 as being in REV B and later boards not REV A
boards. Looks too good of a solder job and such to be anything other than
factory so either this board is mislabeled for REV #'s or was one of the
first boards to have R622 put in it before official REV B designation
assigned. --OMIT THE ABOVE SENTENCE AS I WAS looking at wrong parts listing
and hit send to quick--

(Reason is this board had both pots R622 and R608 totally at one of the
stops-full CCW--along with other adjustments at one end or the other before
I started with it)

At this point everything is working in this repeater and working close to
where it should be as audio levels just aren't up to snuff and a little on
the weak side. . . .
(will trace audio on next trip to the mountain and go from there)

Thanks all
Tony, KA3VOR

Reply via email to