John, I did not find Stabilant listed in the Electro-Sonic online catalog, but I did find the identical kit at Micro-Tools for only $38, here: <www.micro-tools.com/store/P-22/Stabilant-22-5ml-Kit-Makes-30ml-Of-22a.aspx>
I also found that Amazon sells the same kit as Micro-Tools, and for the same price of $38. I should point out that the kit does NOT make 30 ml of solution, as the listing implies; if the instructions are followed exactly- adding 10 ml of alcohol to 2.5 ml of pure Stabilant- the kit will make a total of 25 ml of solution. That's because the 15 ml bottle is filled only to the 12.5 ml point, where the bottle begins to narrow. 73, Eric Lemmon WB6FLY -----Original Message----- From: Repeater-Builder@yahoogroups.com [mailto:repeater-buil...@yahoogroups.com] On Behalf Of John J. Riddell Sent: Saturday, September 04, 2010 11:47 AM To: Repeater-Builder@yahoogroups.com Subject: Re: [Repeater-Builder] Micor Pin "Gunk" Eric, you're singing my tune ! I've used that stuff for many years now and it is really great. It was developed here in Richmond Hill, Ontario, Canada by DW Electrochemicals. As you know only a very small amount is needed on the surface to be effective. The last bottle that I purchased here in Waterloo cost around $35.00. I'd bet that Electro-Sonic would carry it and they are now in the Buffalo area....might be quite a bit cheaper than the Motorola price... John VE3AMZ ----- Original Message ----- From: "Eric Lemmon" <wb6...@verizon.net <mailto:wb6fly%40verizon.net> > To: <Repeater-Builder@yahoogroups.com <mailto:Repeater-Builder%40yahoogroups.com> > Sent: Saturday, September 04, 2010 2:13 PM Subject: RE: [Repeater-Builder] Micor Pin "Gunk" > Tom, > > Motorola does not now, and never has, recommended DeOxit or any other > contact enhancer "gunk" besides Stabilant 22. Up until just a few years > ago, Motorola specified Stabilant 22A, under part number 1180369E78, which > is a mixture of pure Stabilant 22 and isopropyl alcohol. Today, Motorola > sells a kit under part number 1180384V93 which comprises a 5 ml bottle of > pure Stabilant 22, an empty 15 ml bottle, and some tiny swabs. The user > then puts 2.5 ml of the Stabilant 22 into the 15 ml bottle and adds 10 ml of > 99% isopropanol to make a working solution of Stabilant 22A, or adds 10 ml > of pure ethanol to make a working solution of Stabilant 22E. Either > solution is extremely effective if applied wet to clean connectors > immediately before mating. It is also effective in curing intermittent > contacts in card-edge connectors in PCs and electronic instruments. The > alcohol solvent is essential for the product to work; undiluted Stabilant 22 > is ineffective. Drug-store isopropyl alcohol, aka rubbing alcohol, should > not be used since it is diluted with water and will interfere with > Stabilant's action. > > The 1180384V93 kit is sold by Motorola Parts for about $47, but is > sufficient to last for years. > > 73, Eric Lemmon WB6FLY > > > > -----Original Message----- > From: Repeater-Builder@yahoogroups.com <mailto:Repeater-Builder%40yahoogroups.com> > [mailto:Repeater-Builder@yahoogroups.com <mailto:Repeater-Builder%40yahoogroups.com> ] On Behalf Of w9srv > Sent: Saturday, September 04, 2010 10:28 AM > To: Repeater-Builder@yahoogroups.com <mailto:Repeater-Builder%40yahoogroups.com> > Subject: [Repeater-Builder] Micor Pin "Gunk" > > > > Hi Guys! > > I am in the middle of rebuilding a receive site for one of the area > repeaters and have come across some interesting "Pin Gunk". I've been told > that Motorola techs years ago used to apply some kind of "goo" to help with > the connection on all the backplane pins, etc, but I don't know if this is > what that is. This receive site has been developing some intermittant issues > on several fronts, and maybe this explains them. > > The problem with this gunk is that is is non-conductive and a real bugger to > clean off. DeOxit seems to work the best. I made this quick video last night > showing this on the pins of the power control board. Here is the link to the > video: > > http://www.youtube.com/watch?v=tmWumkQetdY > > Has anyone else ever come across this? Are there any other steps other than > cleaning it off to ensure it will not be another problem in the future? > > Thanks! > > Tom > W9SRV > > > > ------------------------------------ > > > > Yahoo! Groups Links > > >
