You're right, I forgot this feature was added. Honestly I don't have
experience using it.

I think this was added since the last official release, though. You may have
to install a nightly, using:

$ easy_install -f http://downloads.review-board.org/nightlies/ -U RBTools

Christian

-- 
Christian Hammond - chip...@chipx86.com
Review Board - http://www.review-board.org
VMware, Inc. - http://www.vmware.com


On Tue, Jun 16, 2009 at 8:02 AM, saadware <saa...@gmail.com> wrote:

>
> OK. I'm confused a bit. Look at the "Contents" section on the right
> side of the page.
>
>
> http://www.review-board.org/docs/manual/dev/users/tools/post-review/#posting-paths
>
> You'll notice that the docs seem to indicate that posting paths is
> supported in Perforce, as "Posting Paths" is located underneath the
> "Perforce" section.
>
> This may not be supported still, but I'm just curious why the docs
> seem to indicate that it is.
>
> Best regards,
> Scott
>
> On Jun 15, 10:27 pm, Christian Hammond <chip...@chipx86.com> wrote:
> > Oh, so you want to post an entire file up for review?
> >
> > This isn't supported by post-review directly. You'd have to generate a
> diff
> > containing the contents of the entire file and post it up for review
> through
> > the web UI.
> >
> > It's possible someone else on this mailing list may have a script or
> > strategy for automating this.
> >
> > Christian
> >
> > --
> > Christian Hammond - chip...@chipx86.com
> > Review Board -http://www.review-board.org
> > VMware, Inc. -http://www.vmware.com
> >
> >
> >
> > On Mon, Jun 15, 2009 at 8:56 PM, Scott Saad <saa...@gmail.com> wrote:
> > > It is against Perforce. I'm trying to accomplish getting a file(s)
> posted
> > > without generating a diff from the previous revision. Kind of like when
> a
> > > new file shows up for the first time.
> >
> > > I misunderstood the docs. Is this possible with Perforce?
> >
> > > Scott
> >
> > > On Jun 15, 2009, at 16:45, Christian Hammond <chip...@chipx86.com>
> wrote:
> >
> > > Is this against Perforce?
> >
> > > When using Perforce, you need to create a changeset with the files you
> want
> > > to post and use that changeset number instead. The file paths support
> is for
> > > Subversion, CVS, etc.
> >
> > > Christian
> >
> > > --
> > > Christian Hammond - <chip...@chipx86.com>chip...@chipx86.com
> > > Review Board - <http://www.review-board.org>
> http://www.review-board.org
> > > VMware, Inc. - <http://www.vmware.com>http://www.vmware.com
> >
> > > On Mon, Jun 15, 2009 at 2:44 PM, saadware < <saa...@gmail.com>
> > > saa...@gmail.com> wrote:
> >
> > >> I'm trying to post a path (opposed to a changelist) as laid out in the
> > >> docs:
> >
> > >> <
> http://www.review-board.org/docs/manual/dev/users/tools/post-review/#...>
> > >>http://www.review-board.org/docs/manual/dev/users/tools/post-review/#.
> ..
> >
> > >> If I run the following command:
> >
> > >>  post-review //path/to/dir/...
> >
> > >> I get the following error message:
> >
> > >>  You must enter a valid change number.
> >
> > >> It may just be a case where I'm misunderstanding the docs. Should this
> > >> be possible?
> >
> > >> Kind regards,
> > >> Scott
>
> >
>

--~--~---------~--~----~------------~-------~--~----~
You received this message because you are subscribed to the Google Groups 
"reviewboard" group.
To post to this group, send email to reviewboard@googlegroups.com
To unsubscribe from this group, send email to 
reviewboard+unsubscr...@googlegroups.com
For more options, visit this group at 
http://groups.google.com/group/reviewboard?hl=en
-~----------~----~----~----~------~----~------~--~---

Reply via email to