Im definitely using R14B3 running "riak console" gives me the same errors
On Wed, Nov 9, 2011 at 1:49 PM, Jared Morrow <[email protected]> wrote: > Like I said, you seem to be using R15 in your building of riak, that's why > you have a erts-5.9 directory instead of erts-5.8.4. Please uninstall > your erlang version, and try using erlang-r14b03. Using something like > kerl <https://github.com/spawngrid/kerl> will make it easier to manage > multiple versions of erlang. > > Good luck, > Jared > > > On Wed, Nov 9, 2011 at 12:59 AM, Ivan Trajkovic <[email protected]>wrote: > >> @Andrew >> erlang builds fine every time, never had a problem with that. >> following the riak build sequence to the letter that you listed riak >> builds fine like last time >> but the same message comes up: >> >> //------------------------------------------------------------------------------------------------ >> ~/Desktop/riak/rel/riak$ bin/riak start >> escript: Failed to open file: >> ~/Desktop/riak/rel/riak/erts-5.9/bin/nodetoolbellowescript: Failed to open >> file: ~/Desktop/riak/rel/riak/erts-5.9/bin/nodetool >> Error reading ~/Desktop/riak/rel/riak/etc/app.config >> >> //------------------------------------------------------------------------------------------------ >> so then I went ahead and tried out to see what happens if I move >> "nodetool" from erts-5.8.4 to erts-5-9, which is where it seems to be >> looking for it at, only to get further new errors: >> >> //------------------------------------------------------------------------------------------------ >> ~/Desktop/riak/rel/riak$ mv erts-5.8.4/bin/nodetool erts-5.9/bin/ >> ~/Desktop/riak/rel/riak$ bin/riak start >> >> Crash dump was written to: erl_crash.dump >> init terminating in do_boot () >> >> Crash dump was written to: erl_crash.dump >> init terminating in do_boot () >> Error reading ~/Desktop/riak/rel/riak/etc/app.config >> {"init terminating in do_boot",{'cannot get bootfile','start_clean.boot'}} >> >> //------------------------------------------------------------------------------------------------ >> >> thanks >> >> On Tue, Nov 8, 2011 at 11:44 PM, Andrew Musselman < >> [email protected]> wrote: >> >>> Have you tried this series of commands? >>> >>> >>> wget http://erlang.org/download/otp_src_R14B03.tar.gz >>> tar xzvf otp_src_R14B03.tar.gz >>> cd otp_src_R14B03/ >>> ./configure && make && sudo make install >>> >>> git clone https://github.com/basho/riak.git >>> cd riak/ >>> git checkout 1.0.1-release >>> git fetch >>> git pull >>> make rel >>> >>> If that fails please answer with relevant errors along the way.. >>> >>> Best >>> Andrew >>> >>> >>> On 11/08/2011 06:23 PM, Ivan Trajkovic wrote: >>> >>> I have ubuntu 11.04, not 11.10 >>> could that be an issue >>> >>> On Tue, Nov 8, 2011 at 8:14 PM, Andrew Musselman < >>> [email protected]> wrote: >>> >>>> I can confirm building both erlang and riak from source on Ubuntu >>>> 11.10 works. >>>> >>>> That is, everything builds without any complaints or editing config >>>> files, and then I'm able to add an object to a riak client. >>>> >>>> wget http://erlang.org/download/otp_src_R14B03.tar.gz >>>> tar xzvf otp_src_R14B03.tar.gz >>>> cd otp_src_R14B03/ >>>> ./configure && make && sudo make install >>>> >>>> git clone https://github.com/basho/riak.git >>>> cd riak/ >>>> git checkout 1.0.1-release >>>> git fetch >>>> git pull >>>> make rel >>>> >>>> Thanks all for the advice. >>>> >>>> Best >>>> Andrew >>>> >>>> >>>> >>>> On 11/08/2011 04:49 PM, Ivan Trajkovic wrote: >>>> >>>> yep encountered that issue already and made sure Im using whats >>>> supported >>>> so R14B3, and checking out riak-1.0.1 >>>> >>>> On Tue, Nov 8, 2011 at 7:17 PM, Jared Morrow <[email protected]> wrote: >>>> >>>>> When you say you are building from source (github) 1.0.1, are you >>>>> doing a 'git checkout riak-1.0.1' or building from 'master'? One note, >>>>> based on your erts version, you are using a newer erlang than we support. >>>>> We have not built or tested Riak against erlang R15. Try using R14B02 or >>>>> R14B03 for Riak 1.0.1. If you are building Riak off of master, you can >>>>> use R14B04 as well. >>>>> >>>>> -Jared >>>>> >>>>> On Tue, Nov 8, 2011 at 3:45 PM, Ivan Trajkovic >>>>> <[email protected]>wrote: >>>>> >>>>>> hi Jared, thank you for your fast response... >>>>>> interestingly riak 1.0.1 does build now, from source (github)... >>>>>> unlike before... not really sure what changed. >>>>>> but the old errors are coming up again, when trying to start riak: >>>>>> >>>>>> ~/Desktop/riak/rel/riak$ bin/riak start >>>>>> escript: Failed to open file: >>>>>> ~/Desktop/riak/rel/riak/erts-5.9/bin/nodetool >>>>>> escript: Failed to open file: >>>>>> ~/Desktop/riak/rel/riak/erts-5.9/bin/nodetool >>>>>> Error reading ~/Desktop/riak/rel/riak/etc/app.config >>>>>> >>>>>> >>>>>> erts-5.9/bin/nodetool really isnt there >>>>>> app.config however is present, but Im guessing that error is >>>>>> dependent on the nodetool failure error coming up >>>>>> >>>>>> >>>>>> >>>>> <Thread deleted for size constraints > >>>>> >>>> >>>> >>>> >>>> _______________________________________________ >>>> riak-users mailing >>>> [email protected]http://lists.basho.com/mailman/listinfo/riak-users_lists.basho.com >>>> >>>> >>>> >>> >>> >>> _______________________________________________ >>> riak-users mailing >>> [email protected]http://lists.basho.com/mailman/listinfo/riak-users_lists.basho.com >>> >>> >>> >> >> _______________________________________________ >> riak-users mailing list >> [email protected] >> http://lists.basho.com/mailman/listinfo/riak-users_lists.basho.com >> >> >
_______________________________________________ riak-users mailing list [email protected] http://lists.basho.com/mailman/listinfo/riak-users_lists.basho.com
