>>> sender: "Bogdan-Stefan Rotariu" date: "Fri, Aug 25, 2006 at 07:28:57PM
>>> +0300" <<<EOQ
> Prin xfree era glint care era driver pt. 3Dlabs si inca ceva, ai incercat?
Merci de sugestie. Din pacate se pare ca nu-i prea place modelul meu:
--- Xorg.0.log ---
(II) LoadModule: "glint"
(II) Loading /usr/X11R6/lib/modules/drivers/glint_drv.o
(II) Module glint: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 0.7
(II) GLINT: driver for 3Dlabs chipsets: gamma, gamma2, ti_pm2, ti_pm, r4,
pm4, pm3, pm2v, pm2, pm, 300sx, 500tx, mx, delta
(II) Primary Device is: PCI 01:00:0
(--) Assigning device section with no busID to primary device
(WW) GLINT: No matching Device section for instance (BusID PCI:1:0:1) found
(EE) No devices detected.
--- end ---
--- lspci -vv ---
01:00.0 VGA compatible controller: 3DLabs Wildcat III 6210 (rev 01) (prog-if 00
[VGA])
Subsystem: 3DLabs: Unknown device 1021
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at f4000000 (32-bit, prefetchable) [size=64M]
Region 2: Memory at fdef0000 (32-bit, non-prefetchable) [size=64K]
Region 3: Memory at f3000000 (32-bit, prefetchable) [size=16M]
Expansion ROM at c1000000 [disabled] [size=256K]
Capabilities: [68] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] AGP version 2.0
Status: RQ=8 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans-
64bit+ FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
01:00.1 Display controller: 3DLabs Wildcat III 6210 (rev 01)
Subsystem: 3DLabs: Unknown device 1021
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Region 0: Memory at fdeef000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [68] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
--- end ---
O sa incerc cu driverele lor pt RHEL3 sa vad ce reusesc.
Merci oricum,
O zi buna tuturor,
Alex
_______________________________________________
RLUG mailing list
[email protected]
http://lists.lug.ro/mailman/listinfo/rlug
