salut
intampin probleme in a face sa mearga tandemul linux bonding - switch allied
telesyn at-gs950 in mod 802.3ad
am configurat switch-ul cu cele doua porturi in truncking (in documentatie zice
ca e 802.3ad compliant)
am configurat linuxu astfel:
-> modprobe.conf
alias bond0 bonding
options bond0 mode=4 miimon=100 downdelay=500 updelay=500 use_carrier=1
lacp_rate=1
-> ifcfg-bond0
DEVICE=bond0
IPADDR=192.168.124.222
NETMASK=255.255.255.0
NETWORK=192.168.124.0
BROADCAST=192.168.124.255
ONBOOT=yes
BOOTPROTO=none
USERCTL=no
-> ifcfg-eth0
DEVICE=eth0
USERCTL=no
ONBOOT=yes
MASTER=bond0
SLAVE=yes
BOOTPROTO=none
-> ifcfg-eth1
DEVICE=eth1
USERCTL=no
ONBOOT=yes
MASTER=bond0
SLAVE=yes
BOOTPROTO=none
cele 2 placi de retea sunt Intel 82573E si merg cu modulul e1000e
in functionare avem:
bond0 Link encap:Ethernet HWaddr 00:30:48:56:19:F6
inet addr:192.168.124.222 Bcast:192.168.124.255 Mask:255.255.255.0
inet6 addr: fe80::230:48ff:fe56:19f6/64 Scope:Link
UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1
RX packets:5193 errors:0 dropped:0 overruns:0 frame:0
TX packets:3098 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:784291 (765.9 KiB) TX bytes:375984 (367.1 KiB)
eth0 Link encap:Ethernet HWaddr 00:30:48:56:19:F6
UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:4877 errors:0 dropped:0 overruns:0 frame:0
TX packets:1621 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:756889 (739.1 KiB) TX bytes:192836 (188.3 KiB)
Memory:ed300000-ed320000
eth1 Link encap:Ethernet HWaddr 00:30:48:56:19:F6
UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:316 errors:0 dropped:0 overruns:0 frame:0
TX packets:1477 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:27402 (26.7 KiB) TX bytes:183148 (178.8 KiB)
Memory:ed400000-ed420000
deci se vede si ceva trafic pe eth0 si eth1 si teth0 + teth1 = tbond0
si
[r...@gw ~]# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2 (0)
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 500
Down Delay (ms): 500
802.3ad info
LACP rate: fast
Aggregator selection policy (ad_select): stable
Active Aggregator Info:
Aggregator ID: 3
Number of ports: 1
Actor Key: 17
Partner Key: 1
Partner Mac Address: 00:00:00:00:00:00
Slave Interface: eth0
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:30:48:56:19:f6
Aggregator ID: 3
Slave Interface: eth1
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:30:48:56:19:f7
Aggregator ID: 5
deci se pare ca pe lacp nu se schimba nimic intre linux si switch
problema? -> nu prea se poate comunica cu exteriorul
mac-urile sunt invatate corect uneori, alteori deloc, atat de server-ul cu
pricina, cat si de catre celelalte statii cu care fac teste -> n-am reusit
sa-mi
dau seama care e motivul care face diferenta
daca dau ping de pe o statie catre server si simultan dau pe acesta o comanda
de
tipul:
ifenslave -d bond0 eth1
trec 2~3 reply-uri dupa care liniste (!?!?!?)
la fel si cand dau apoi:
ifenslave bond0 eth1
si reciproca e adevarata
am incercat fara succes:
* kernel 2.6.33 in loc de 2.6.18-x cu care vine centos;
* alte 2 placi de retea, tot intel dar de generatie mai veche, cu modul e1000;
* truncking pe switch cu alte 2 porturi;
ce sa-i mai fac?
oare e prost telesica? sau fac eu ceva gresit?
aveti experiente cu swich-uri allied telesyn + bonding + linux?
_______________________________________________
RLUG mailing list
[email protected]
http://lists.lug.ro/mailman/listinfo/rlug
