On Mon, 4 Nov 2002, AngelOfMist wrote: > eth0 Link encap:Ethernet HWaddr 00:10:B5:55:85:D1 > inet addr:62.231.x.x Bcast:62.231.x.x Mask:255.255.255.0 daca providerul are /24 e ok (si eu cred ca are daca e cine cred eu ca e ;) )
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:4253130 errors:0 dropped:0 overruns:0 frame:0 > TX packets:736427 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:100 > RX bytes:2236119522 (2132.5 Mb) TX bytes:59079719 (56.3 Mb) > Interrupt:5 Base address:0x9f00 > > eth0:0 Link encap:Ethernet HWaddr 00:10:B5:55:85:D1 > inet addr:194.102.x.x Bcast:194.102.163.255 Mask:255.255.255.0 aci e WROOOOOONG! ce cauta mask 255.255.255.0 ? subnetul tau e mai mic aici tre sa pui mask 255.255.255.248 (parca de 8 era) > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > Interrupt:5 Base address:0x9f00 > > eth1 Link encap:Ethernet HWaddr 08:00:30:00:35:A0 > inet addr:192.168.3.1 Bcast:192.168.3.255 Mask:255.255.255.0 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:730403 errors:0 dropped:0 overruns:0 frame:0 > TX packets:1286577 errors:0 dropped:0 overruns:0 carrier:0 > collisions:1631 txqueuelen:100 > RX bytes:58721918 (56.0 Mb) TX bytes:1797696333 (1714.4 Mb) > Interrupt:15 Base address:0x74e0 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > UP LOOPBACK RUNNING MTU:3924 Metric:1 > RX packets:4898 errors:0 dropped:0 overruns:0 frame:0 > TX packets:4898 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:501129 (489.3 Kb) TX bytes:501129 (489.3 Kb) > > asta e gw > ---------------------------------------------------------------------------- > ---- > > eth0 Link encap:Ethernet HWaddr 00:02:55:A0:EC:33 > inet addr:194.102.x.z Bcast:194.102.x.255 Mask:255.255.255.0 aici iar e gresit deci man daca ai parimit 194.102.x.y/255.255.255.248 atunci TOATE ip-urile din acea retea vor avea acelasi netmask deci si aici trebuie netmask 255.255.255.248 faza e ca dupa ce configurezi interfetele bine ai sa vezi ca nu ai nevoie de nici o smecherie speciala ca sa mearga pe gw... deci configureaza-le bine si apoi da iar un ifconfing | grep inet si un route -n > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:270300 errors:0 dropped:0 overruns:0 frame:0 > TX packets:149539 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:100 > RX bytes:367617277 (350.5 Mb) TX bytes:10865343 (10.3 Mb) > Interrupt:14 Base address:0xd000 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > UP LOOPBACK RUNNING MTU:3924 Metric:1 > RX packets:110 errors:0 dropped:0 overruns:0 frame:0 > TX packets:110 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:11204 (10.9 Kb) TX bytes:11204 (10.9 Kb) > > asta e serv mail > > --- > Pentru dezabonare, trimiteti mail la > [EMAIL PROTECTED] cu subiectul 'unsubscribe rlug'. > REGULI, arhive si alte informatii: http://www.lug.ro/mlist/ > > > ---------------------------- Mihai RUSU Disclaimer: Any views or opinions presented within this e-mail are solely those of the author and do not necessarily represent those of any company, unless otherwise specifically stated. --- Pentru dezabonare, trimiteti mail la [EMAIL PROTECTED] cu subiectul 'unsubscribe rlug'. REGULI, arhive si alte informatii: http://www.lug.ro/mlist/
