-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Salut
Pt cei care intreabau de suportul SATA in linux :) - -- Mihai RUSU Email: [EMAIL PROTECTED] GPG : http://dizzy.roedu.net/dizzy-gpg.txt WWW: http://dizzy.roedu.net "Linux is obsolete" -- AST - ---------- Forwarded message ---------- Date: Wed, 25 Feb 2004 21:34:37 -0500 From: Jeff Garzik <[EMAIL PROTECTED]> To: Linux Kernel <[EMAIL PROTECTED]> Subject: Serial ATA (SATA) status report attached. Serial ATA (SATA) for Linux status report Feb 25, 2004 Hardware support ================ Intel ICH5 and ICH5-R - --------------------- Summary: No TCQ. Looks like a PATA controller, but with a few added, non-standard SATA port controls. Hardware does not support hotplug. "Coldplug" support is potentially feasible. libata driver status: Production, but see issue #2, #3, #4. drivers/ide driver status: Production, but see issue #1, #2. Issue #1: Depending on BIOS settings, IDE driver may lock up computer when probing drives. Issue #2: Excessive interrupts are seen in some configurations. Issue #3: "Enhanced mode" or "SATA-only mode" may need to be set in BIOS. Issue #4: Driver disables SATA port on unload, but does not re-enable SATA port on load. Intel ICH6 ("AHCI") - ------------------- Summary: Per-device queues, full SATA control including hotplug and PM. libata driver status: "looks like ICH5" support available in ata_piix very soon. Full support available in a week or two. Promise TX2/TX4/SX4 - ------------------- Summary: Per-host queues on all controllers. Full SATA control including hotplug and PM on all but one controller. libata driver status: Beta, but see issue #5. Issue #5: Some boards appear to have PATA as well as SATA ports. PATA is not currently supported, and no plans have yet been made to rectify this. Ideally drivers/ide would drive PATA, but if they are the same PCI device, that would not be feasible. Silicon Image 3112/3114 - ----------------------- Summary: No TCQ. Looks like a PATA controller, but with full SATA control including hotplug and PM. libata driver status: Alpha. drivers/ide driver status: Production, but see issue #4. Issue #4: Need to have the most recent fixes posted to lkml, for stable operation and full performance (where possible). Silicon Image 3124 - ------------------ Soon, hopefully. User-written. Broadcom/ServerWorks/Apple - -------------------------- Summary: Huge per-device queues, full SATA control including hotplug and PM. libata driver status: Beta. VIA - --- Summary: No TCQ. Looks like a PATA controller, but with full SATA control including hotplug and PM. libata driver status: Beta. SiS - --- libata driver status: in progress (user-written) Vitesse - ------- libata driver status: in progress Marvell - ------- libata driver status: in progress Software support ================ Basic Serial ATA support - ------------------------ The "ATA host state machine", the core of the entire driver, is considered production-stable. The error handling is _very_ simple, but at this stage that is an advantage. Error handling code anywhere is inevitably both complex and sorely under-tested. libata error handling is intentionally simple. Positives: Easy to review and verify correctness. Never data corruption. Negatives: if an error occurs, libata will simply send the error back the block layer. There are limited retries by the block layer, depending on the type of error, but there is never a bus reset. Or in other words: "it's better to stop talking to the disk than compound existing problems with further problems." As Serial ATA matures, and host- and device-side errata become apparent, the error handling will be slowly refined. I am planning to work with a few (kind!) disk vendors, to obtain special drives/firmwares that allow me to inject faults, and otherwise exercise error handling code. Queueing support - ---------------- Even though some SATA host controllers on the market already support command queueing (a.k.a. "TCQ"), libata does not yet support it. However, libata was designed from the ground-up to support queueing, so I need only change a few lines of code, and write two functions, to enable this behavior. Queueing will be enabled in libata soon, but to do so requires a long stretch of testing on a large variety of controllers and drives. This is very time-intensive, and is the largest part of this task. Tangent: Host-based queueing and Native Command Queueing Queueing is the process of sending multiple commands to a single device, without waiting for prior commands to finish. This increases performance and reduces latency. There are three types of queueing in the ATA world: 1) "legacy TCQ" -- some PATA devices support this. Just ignore it, it's going away. 2) "host-based TCQ" -- the host controller supports a queue of drive commands, whether or not the drive supports it. 3) "Native Command Queueing" -- both host and drive cooperate in the queueing and execution of drive commands. This should provide the highest performance and lowest latency of all three options. #1 is support by drivers/ide _only_. libata will not support this. #2 will soon be supported by libata. #3 will be supported by libata when hardware is available from drive manufacturers. Hotplug support - --------------- All SATA is hotplug. libata does not support hotplug... yet. Power Management support - ------------------------ Over and above the power management specified in the ATA/ATAPI specification, one can aggressively control the power consumption of SATA hosts, the SATA bus, and the SATA device. SMART support - ------------- Soon. Requires the capability to directly submit ATA commands from userspace to the low-level device, which must be added with care. -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.4 (GNU/Linux) iD8DBQFAPcAUPZzOzrZY/1QRAqDzAJ9IEp1zPlulB+/inBwPG0GmzVzrgQCbBG/O /4TE20z/gh8CmSdXZn+Q2to= =w8Zb -----END PGP SIGNATURE----- --- Detalii despre listele noastre de mail: http://www.lug.ro/
