Buna listashi
Imi permit a va scrie cu rugamintea de a ma ajuta sa fac lirc-ul sa
functioneze
In acest moment pe un AMD K6/II 450 Mhz cu 256 Mb Ram si Voodoo Banshee
16 Mb,
am instalat Slackware-9.1 cu (precizare importanta) XFree-4.4.0 deci
upgradat.
Kernel-ul e cel default al distributiei ( Daca e problema cu X-ul revin
la default)
Tuner instalat am PV-BT8748P+ (REV J.9f) avind ca optiuni in
/etc/modules.conf:
####################/etc/modules.conf####################
alias char-major-81 videodev
alias char-major-81-0 bttv
alias char-major-81-1 tvaudio
options bttv card=37 tuner=29 radio=1 pll=1 bttv_gpio=1
options tuner debug=1 type=5
alias char-major-89 i2c-dev
options i2c-core i2c_debug=1
options i2c-algo-bit bit_test=1
alias char-major-61 lirc_gpio
options lirc_gpio gpio_mask=0x3f00 gpio_lock_mask=0x4000 \
gpio_xor_mask=0 soft_gap=400 sample_rate=12mask=0 soft_gap=400
sample_rate=12
##########################################################
In /etc/X11/XF86Config am pus
Load "v4l" #la sectiunea Module
in /etc/rc.d/rc.modules lucrurile arata astfel :
#############/etc/rc.d/rc.modules###########
/sbin/modprobe i2c-dev
/sbin/modprobw i2c-core
/sbin/modprobe i2c-algo-bit
/sbin/modprobe videodev
/sbin/modprobe bttv
/sbin/modprobe tuner
/sbin/modprobe tvaudio
/sbin/modprobe lirc_dev
/sbin/modprobe lirc_gpio
#################################
(Am pus numai ce am adaugat eu)
/etc/lircd.conf-ul arata astfel:
################/etc/lircd.conf ###########
#
# this is a space encoded remote control from Technisat
#
# contributed by Christoph Bartelmus ([EMAIL PROTECTED])
#
# brand: Technisat
# model: 100 TS 008
# supported devices: satellite receiver ST 3004 S
#
begin remote
name Pixelview TV pro
bits 8
eps 30
aeps 100
one 0 0
zero 0 0
gap 499984
toggle_bit 0
begin codes
tv/fm 0x0000000000000003
source 0x0000000000000006
scan 0x000000000000001C
power 0x000000000000001E
1 0x0000000000000001
2 0x000000000000000B
3 0x000000000000001B
4 0x0000000000000005
5 0x0000000000000009
6 0x0000000000000015
7 0x0000000000000006
8 0x000000000000000A
9 0x0000000000000012
0 0x0000000000000002
recall 0x0000000000000013
+100 0x0000000000000010
record 0x0000000000000000
stop 0x0000000000000008
play 0x0000000000000011
freeze 0x000000000000001A
zoom 0x0000000000000019
<< 0x0000000000000004
function 0x000000000000000E
>> 0x000000000000000C
mts 0x000000000000000D
reset 0x000000000000001D
min 0x000000000000000F
ch+ 0x000000000000001F
ch- 0x0000000000000017
vol+ 0x0000000000000016
vol- 0x0000000000000014
mute 0x0000000000000018
end codes
end remote
########################################
De instalat pentru vizionare am instalat
1) xawtv-3.74 facut tgz dintr-un rpm, daca are importanta,
2) qtvision-ul ultimul racnet de la KwinTV, compilat din surse.
3) lirc-0.6.6.
Ambele player-e TV functioneaza fff.bine, DAR NU si telecomanda, care
fie spus
e functionala , ca din windows, pe acelasi comp, e OK, deci NU e defecta.
Ce probleme am si va rog lamuriti-ma:
1) NU stiu daca sistemul primeste semnale de la telecomanda.
Ce trebuie facut sa aflu daca sistemul reactioneaza sau nu ??
2) Ce mai trebuie facut ??
Mai tre sa scriu in XF86Config ??
Va multumesc
---
Detalii despre listele noastre de mail: http://www.lug.ro/
