Hi Thankyou in advance details of problem/computer p133 running redhat 7.3 -kernel 2.4.18-3 pci scsi card buslogic bt930 scanner hp scanjet IIcx (ca2500A)
scanner is detected on startup /var/log/dmesg <snip> subsystem driver Revision: 1.00: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2: Found IRQ 9 for device 00:0b.0: ***** BusLogic SCSI Driver Version 2.1.15 of 17 August 1998 *****: Copyright 1995-1998 by Leonard N. Zubkoff <[email protected]>: Configuring BusLogic Model BT-930 PCI Ultra SCSI Host Adapter: Firmware Version: 5.02, I/O Address: 0x6C00, IRQ Channel: 9/Level: PCI Bus: 0, Device: 11, Address: 0xE2001000, Host Adapter SCSI ID: 7: Parity Checking: Enabled, Extended Translation: Enabled: Synchronous Negotiation: UUUUUFN#, Wide Negotiation: Disabled: Disconnect/Reconnect: YYYYYYN#, Tagged Queuing: YYYYYYN#: Driver Queue Depth: 255, Scatter/Gather Limit: 128 segments: Tagged Queue Depth: Automatic, Untagged Queue Depth: 3: Error Recovery Strategy: Default, SCSI Bus Reset: Enabled: SCSI Bus Termination: Enabled, SCAM: Disabled: *** BusLogic BT-930 Initialized Successfully ***: BusLogic BT-930 Vendor: HP Model: C2500A Rev: 3332 Type: Processor ANSI SCSI revision: 02: Target 6: Queue Depth 3, AsynchronousBlock Device driver loaded <snip> (plus ide device): SCSI host adapter emulation for IDE ATAPI devices Vendor: AOPEN Model: CD-RW CRW2040 Rev: 1.21 Type: CD-ROM ANSI SCSI revision: 02: DMA disabled /etc/scsi/scsi Attached devices: : scsi0 Channel: 00 Id: 06 Lun: 00 Vendor: HP Model: C2500A Rev: 3332 Type: Processor ANSI SCSI revision: 02: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: AOPEN Model: CD-RW CRW2040 Rev: 1.21 Type: CD-ROM ANSI SCSI revision: 02 when i run sane-find-scanner # Note that sane-find-scanner will find any scanner that is connected # to a SCSI bus and some scanners that are connected to the Universal # Serial Bus (USB) depending on your OS. It will even find scanners # that are not supported at all by SANE. It won't find a scanner that # is connected to a parallel or proprietary port. find-scanner: found SCSI processor "HP C2500A 3332" at device /dev/scannerfind-scanner: found SCSI processor "HP C2500A 3332" at device /dev/sg0find-scanner: found SCSI processor "HP C2500A 3332" at device /dev/sga i do have messages in /var/log/messages when i run sane-find-scanner i get Dec 6 07:40:25 fergusson last message repeated 3 times 6 07:41:40 fergusson kernel: ide-scsi: The scsi wants to send us more data than expected - discarding data 6 07:41:40 fergusson kernel: ide-scsi: transferred 5 of 6 bytes 6 07:41:40 fergusson kernel: ide-scsi: The scsi wants to send us more data than expected - discarding data 6 07:41:40 fergusson kernel: ide-scsi: transferred 5 of 6 bytes 6 07:43:12 when i run scanimage --list-device fergusson modprobe: modprobe: Can't locate module char-major- 81 I hope i have given enough info - looks like i have some problem in my scsi module ?(me being far from expert) versions of sane sane-backends-1.0.7-6.1.i386.rpm sane-backends-devel-1.0.7-6.i386.rpm sane-frontends-1.0.7-6.1.i386.rpm Regards Phil Workman [email protected]
