xsane should present you with a dialog to choose scanner if it discovers multiple. It is possible that the v30 is not working at all? What is the output of scanimage -L
allan On Wed, Dec 23, 2009 at 9:37 PM, Dan Morton <morton at rad.upenn.edu> wrote: > I've got a PCI ATI All-in-Wonder video digitizer card, and a new Epson V30 > scanner.? lspci -vv says this about the ATI: > > 11:00.0 Multimedia video controller: Brooktree Corporation Bt878 Video > Capture (rev 02) > Subsystem: ATI Technologies Inc Device 0003 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 132 (4000ns min, 10000ns max) > Interrupt: pin A routed to IRQ 20 > Region 0: Memory at fc800000 (32-bit, prefetchable) [size=4K] > Kernel driver in use: bttv > Kernel modules: bttv > > When I launch XSane, it scans for devices, and preferentially chooses the > All-in-Wonder.? Upon exit, it creates a drc file with this name: > > Noname:BT878video(ATITV-WonderVE).drc > > Here are the contents: > > "XSANE_DEVICE_RC" > "Noname:BT878 video (ATI TV-Wonder VE)" > "xsane-version" > "0.996" > "mode" > "Gray" > "channel" > "Television" > "brightness" > 128 > [snip] > > I presume I want to create another drc file I can choose (Preferences -> > load device settings) that describes the V30 -- but, what should the > contents be?? The contents of the ATI drc bears little semblance to the > information in the lspci output.? What is it in the drc that XSane uses to > choose the device? > > For completeness, I follow with the lsusb -vv for the V30. > > adTHANKSvance, > Dan > > Bus 001 Device 002: ID 04b8:0131 Seiko Epson Corp. > Device Descriptor: > ? bLength??????????????? 18 > ? bDescriptorType???????? 1 > ? bcdUSB?????????????? 2.00 > ? bDeviceClass????????? 255 Vendor Specific Class > ? bDeviceSubClass?????? 255 Vendor Specific Subclass > ? bDeviceProtocol?????? 255 Vendor Specific Protocol > ? bMaxPacketSize0??????? 64 > ? idVendor?????????? 0x04b8 Seiko Epson Corp. > ? idProduct????????? 0x0131 > ? bcdDevice??????????? 1.00 > ? iManufacturer?????????? 1 EPSON > ? iProduct??????????????? 2 EPSON Scanner > ? iSerial???????????????? 0 > ? bNumConfigurations????? 1 > ? Configuration Descriptor: > ??? bLength???????????????? 9 > ??? bDescriptorType???????? 2 > ??? wTotalLength?????????? 32 > ??? bNumInterfaces????????? 1 > ??? bConfigurationValue???? 1 > ??? iConfiguration????????? 0 > ??? bmAttributes???????? 0xc0 > ????? Self Powered > ??? MaxPower??????????????? 2mA > ??? Interface Descriptor: > ????? bLength???????????????? 9 > ????? bDescriptorType???????? 4 > ????? bInterfaceNumber??????? 0 > ????? bAlternateSetting?????? 0 > ????? bNumEndpoints?????????? 2 > ????? bInterfaceClass?????? 255 Vendor Specific Class > ????? bInterfaceSubClass??? 255 Vendor Specific Subclass > ????? bInterfaceProtocol??? 255 Vendor Specific Protocol > ????? iInterface????????????? 0 > ????? Endpoint Descriptor: > ??????? bLength???????????????? 7 > ??????? bDescriptorType???????? 5 > ??????? bEndpointAddress???? 0x81? EP 1 IN > ??????? bmAttributes??????????? 2 > ????????? Transfer Type??????????? Bulk > ????????? Synch Type?????????????? None > ????????? Usage Type?????????????? Data > ??????? wMaxPacketSize???? 0x0200? 1x 512 bytes > ??????? bInterval???????????? 255 > ????? Endpoint Descriptor: > ??????? bLength???????????????? 7 > ??????? bDescriptorType???????? 5 > ??????? bEndpointAddress???? 0x02? EP 2 OUT > ??????? bmAttributes??????????? 2 > ????????? Transfer Type??????????? Bulk > ????????? Synch Type?????????????? None > ????????? Usage Type?????????????? Data > ??????? wMaxPacketSize???? 0x0200? 1x 512 bytes > ??????? bInterval???????????? 255 > Device Qualifier (for other device speed): > ? bLength??????????????? 10 > ? bDescriptorType???????? 6 > ? bcdUSB?????????????? 2.00 > ? bDeviceClass????????? 255 Vendor Specific Class > ? bDeviceSubClass?????? 255 Vendor Specific Subclass > ? bDeviceProtocol?????? 255 Vendor Specific Protocol > ? bMaxPacketSize0??????? 64 > ? bNumConfigurations????? 1 > Device Status:???? 0x0001 > ? Self Powered > > > -- > sane-devel mailing list: sane-devel at lists.alioth.debian.org > http://lists.alioth.debian.org/mailman/listinfo/sane-devel > Unsubscribe: Send mail with subject "unsubscribe your_password" > ? ? ? ? ? ? to sane-devel-request at lists.alioth.debian.org > -- "The truth is an offense, but not a sin"
