Hi Rolf - Thanks for the reply. It seems I had to remove the sane packages installed by debian and re-build. However, I can't seem to figure out how to get a front end installed without wiping out the backend version. Even if I install a package, the try to re-build over the sane-backends upgrades, the backend doesn't upgrade and remains at 1.0.22. Is there something I'm missing? I've been using http://mp610.blogspot.com/ as my build advice.
Thanks! Max Max Resnick Max.Resnick at gmail.com 631-896-8357 On Mon, Dec 3, 2012 at 7:08 AM, Rolf Bensch <webmaster at bensch-online.de>wrote: > Hi Max, > > your scanimage uses the 1.0.22 backend. It must be >=1.0.23. > > Please read README.linux and follow the installation desription. > > Cheers, > Rolf > > Am 02.12.2012 22:54, schrieb Max Resnick: > > Hi Everyone - > > > > -Scanner Model is CanoScane 9000F - and is supported via > > Pixma. http://www.sane-project.org/man/sane-pixma.5.html > > -I'm running Debian Wheezy 64 Bit. > > -I've also tried on Ubuntu 12.04 64 Bit. > > -Scanner runs in windows just fine > > -libusb-dev is installed via apt > > I've ran with the distros installed package 1.0.22 (via APT), I've > > also installed lasest from GIT. ./configure reports usb support > > but lusb0_usb.h doesn't. I'm not sure if lusb0_usb is my issue? > > > > I've got outputs from the following w/ debug enabled if applicable as > > root and non-root user > > -sane-find-scanner > > -scanimage -L > > > > Ultimately, I feel that somehow scanimage -L isnt't checking for USB > > devices. I'm not sure how to force it via pixma.conf? > > > > Again, thanks so much > > > > ##scanimage (sane-backends) 1.0.24git; backend version 1.0.22## > > > > ##sane-find-scanner## > > ##Ran as root, Running as root recognized bus address but fails to > > report the name of the device at bus address### > > # sane-find-scanner will now attempt to detect your scanner. If the > > # result is different from what you expected, first make sure your > > # scanner is powered up and properly connected to your computer. > > > > # No SCSI scanners found. If you expected something different, make > > sure that > > # you have loaded a kernel SCSI driver for your SCSI adapter. > > > > found USB scanner (vendor=0x04a9 [Canon], product=0x1908 [CanoScan]) at > > libusb:001:005 > > # Your USB scanner was (probably) detected. It may or may not be > > supported by > > # SANE. Try scanimage -L and read the backend's manpage. > > > > # Not checking for parallel port scanners. > > > > # Most Scanners connected to the parallel port or other proprietary > ports > > # can't be detected by this program. > > ##Ran as non root user## > > # sane-find-scanner will now attempt to detect your scanner. If the > > # result is different from what you expected, first make sure your > > # scanner is powered up and properly connected to your computer. > > > > # No SCSI scanners found. If you expected something different, make > > sure that > > # you have loaded a kernel SCSI driver for your SCSI adapter. > > > > found USB scanner (vendor=0x04a9, product=0x1908) at libusb:001:005 > > # Your USB scanner was (probably) detected. It may or may not be > > supported by > > # SANE. Try scanimage -L and read the backend's manpage. > > > > # Not checking for parallel port scanners. > > > > # Most Scanners connected to the parallel port or other proprietary > ports > > # can't be detected by this program. > > > > # You may want to run this program as root to find all devices. Once > you > > # found the scanner devices, be sure to adjust access permissions as > > # necessary. > > > > ##sudo SANE_DEBUG_PIXMA=3 scanimage -L## > > [sanei_debug] Setting debug level of pixma to 3. > > [pixma] pixma is compiled with pthread support. > > [pixma] pixma version 0.16.2 > > [pixma] sanei_bjnp_find_devices: > > [pixma] wlan0 is IPv4 capable, sending broadcast.. > > [pixma] wlan0 is IPv4 capable, sending broadcast.. > > [pixma] wlan0 is IPv4 capable, sending broadcast.. > > [pixma] wlan0 is IPv4 capable, sending broadcast.. > > [pixma] wlan0 is IPv4 capable, sending broadcast.. > > [pixma] pixma_find_scanners() found 0 devices > > device `v4l:/dev/video0' is a Noname Integrated Camera virtual device > > > > ##SANE_DEBUG_PIXMA=3 scanimage -L## > > [sanei_debug] Setting debug level of pixma to 3. > > [pixma] pixma is compiled with pthread support. > > [pixma] pixma version 0.16.2 > > [pixma] sanei_bjnp_find_devices: > > [pixma] wlan0 is IPv4 capable, sending broadcast.. > > [pixma] wlan0 is IPv4 capable, sending broadcast.. > > [pixma] wlan0 is IPv4 capable, sending broadcast.. > > [pixma] wlan0 is IPv4 capable, sending broadcast.. > > [pixma] wlan0 is IPv4 capable, sending broadcast.. > > [pixma] pixma_find_scanners() found 0 devices > > device `v4l:/dev/video0' is a Noname Integrated Camera virtual device > > > > > > Max Resnick > > Max.Resnick at gmail.com <mailto:Max.Resnick at gmail.com> > > 631-896-8357 > > > -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.alioth.debian.org/pipermail/sane-devel/attachments/20121206/ae4ca7d9/attachment.html>
