Dear Phil,
[added USB custodian to Cc:]
In message <20160102211834.e49a161...@mail.nwl.cc> you wrote:
> In order to allow for Linux properly register the integrated EHCI host,
> we have to reset it after initialization. Without this, enumeration
> fails if 'usb start' wasn't issued prior to booti
On Sunday, January 03, 2016 at 09:59:23 AM, Wolfgang Denk wrote:
> Dear Phil,
>
> [added USB custodian to Cc:]
Thanks
> In message <20160102211834.e49a161...@mail.nwl.cc> you wrote:
> > In order to allow for Linux properly register the integrated EHCI host,
> > we have to reset it after initiali
On 25/11/2015 14:08, Maximilian Schwerin wrote:
> This patch writes the default values for TXTL and RXTL to UARTx_UFCR.
> Without this patch some older kernel versions crash as UARTx_UFCR was
> not always correctly initialized.
>
> Signed-off-by: Maximilian Schwerin
> ---
Applied to u-boot-imx,
On 08/12/2015 17:08, Eric Nelson wrote:
> Hi Mans,
>
> On 12/08/2015 08:38 AM, Mans Rullgard wrote:
>> If the host clock frequency is higher than 100 MHz, the MDIO hold
>> time needs to be increased from its current setting of one cycle in
>> order to meet the specified minium of 10 ns. Writing a
On 08/12/2015 16:38, Mans Rullgard wrote:
> If fecmxc_initialize_multi() fails, it frees but does not unregister
> the mdio bus, causing subsequent uses of the "mii" command to crash.
> Fix this by adding mdio_unregister() calls where needed.
>
> Signed-off-by: Mans Rullgard
> ---
Applied to u-b
On 10/12/2015 09:58, Michael Schanz wrote:
> Use the macro SETUP_IOMUX_PAD(...) rather than
> imx_iomux_v3_setup_multiple_pads(...) in order to setup
> the pin configuration for ECSPI1.
>
> ARRAY_SIZE(pads) provides the wrong size for
> imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)) in
On Sun, Jan 03, 2016 at 09:26:38AM +0530, Jagan Teki wrote:
> On 2 January 2016 at 22:34, Tom Rini wrote:
> > On Wed, Dec 30, 2015 at 04:04:23PM +0530, Jagan Teki wrote:
> >
> >> Tom,
> >>
> >> Please note that subject shows u-boot-spi/next but it actually
> >> u-boot-spi/master and of course PR s
Hi Michael,
some aditional comments before you will send V3:
On 13/12/2015 12:09, Michael Heimpold wrote:
> Signed-off-by: Michael Heimpold
This is the patch introducing a new board. It is not bad if you add some
info in the commit message, for example which peripherals are already
supported an
On 13/12/2015 12:08, Michael Heimpold wrote:
> For some board designs, it might be useful to switch the DC-DC
> clock source to something else rather the default 24 MHz, e.g.
> for EMI reasons.
>
> For this, override the mxs_power_setup_dcdc_clocksource function
> in your board support files.
>
>
On 18/12/2015 10:38, Gong Qianyu wrote:
> This could avoid executing the code that only applies to i.MX platforms.
>
> The bus_i2c_init() is called before relocation and will assgin value
> to a static variable. If U-Boot is then still running in a flash
> device, it's theoretically not allowed to
On 15/12/2015 09:27, Peng Fan wrote:
> Move setup_display from board_early_init_f to board_init.
> Add more clock settings.
> Add blacklight iomux setting.
> Add display_info_t info for the lvds screen.
>
> Signed-off-by: Peng Fan
> Cc: Fabio Estevam
> Cc: Stefano Babic
> ---
Applied to u-boo
On 15/12/2015 23:27, Mans Rullgard wrote:
> Override the default name_to_gpio() function with one that
> accepts strings of the form bank:pin. If a colon is present
> in the provided name, it behaves like the default version.
>
> This lets the "gpio" command work with sane names rather than
> req
Hi Tom,
my first PR of the year ! Please pull from u-boot-imx, thanks !
The following changes since commit 1d149eddcc0661b683002f76a8240491eba00dbb:
dm: Add timeline and guide for porting serial drivers (2015-11-20
13:59:54 -0500)
are available in the git repository at:
git://www.denx.de/g
On 3 January 2016 at 20:14, Tom Rini wrote:
> On Sun, Jan 03, 2016 at 09:26:38AM +0530, Jagan Teki wrote:
>> On 2 January 2016 at 22:34, Tom Rini wrote:
>> > On Wed, Dec 30, 2015 at 04:04:23PM +0530, Jagan Teki wrote:
>> >
>> >> Tom,
>> >>
>> >> Please note that subject shows u-boot-spi/next but
On Sun, Jan 03, 2016 at 09:10:14PM +0530, Jagan Teki wrote:
> On 3 January 2016 at 20:14, Tom Rini wrote:
> > On Sun, Jan 03, 2016 at 09:26:38AM +0530, Jagan Teki wrote:
> >> On 2 January 2016 at 22:34, Tom Rini wrote:
> >> > On Wed, Dec 30, 2015 at 04:04:23PM +0530, Jagan Teki wrote:
> >> >
> >>
Signed-off-by: Ladislav Michl
---
arch/arm/cpu/armv7/omap-common/utils.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/cpu/armv7/omap-common/utils.c
b/arch/arm/cpu/armv7/omap-common/utils.c
index 602d993..52ea734 100644
--- a/arch/arm/cpu/armv7/omap-common/util
Hi Jagan,
On 22 December 2015 at 12:39, Joe Hershberger wrote:
> Hi Simon,
>
> On Tue, Dec 22, 2015 at 1:14 PM, Joe Hershberger
> wrote:
>> Hi Simon,
>>
>> On Mon, Dec 21, 2015 at 9:17 PM, Joe Hershberger
>> wrote:
>>> Hi Bin and Simon,
>>>
>>> On Mon, Dec 21, 2015 at 9:08 PM, Joe Hershberger
>
Hi Sjoerd,
On 1 October 2015 at 03:48, Sjoerd Simons wrote:
>
>
> This series adds support for the GMAC Ethernet interface on RK3288 SoCs.
>
> To add support I've taken a slightly different approach then some of the
> other boards with a designware IP block, by creating a new driver to
> take car
On Sunday, January 03, 2016 at 03:56:01 PM, Stefano Babic wrote:
> Hi Michael,
>
> some aditional comments before you will send V3:
[...]
> > diff --git a/board/i2se/duckbill/Makefile b/board/i2se/duckbill/Makefile
> > new file mode 100644
> > index 000..b5577e3
> > --- /dev/null
> > +++ b/b
This subsystem has been broken since commit:
4efad20a sf: Update status reg check in spi_flash_cmd_wait_ready
There has so far been no response from the maintainer, and a release is
imminent. For now, let's just disable the tests.
Signed-off-by: Simon Glass
---
test/dm/Makefile | 4 ++--
1
At present USB keyboards are not properly removed with driver model. Add the
code to handle this.
Signed-off-by: Simon Glass
---
common/usb_kbd.c | 36
1 file changed, 36 insertions(+)
diff --git a/common/usb_kbd.c b/common/usb_kbd.c
index 9617a48..7bcab1c
The current limit of 5 is not enough for the driver model USB tests. Really
we should not have a limit but the driver model code still uses the
usb_dev_desc[] array, which has a limit.
Increasing the limit by 2 should not bother anyone. Adjust it.
Signed-off-by: Simon Glass
---
common/usb_stor
On Thursday, December 31, 2015 at 10:34:06 AM, Li Ye-B37916 wrote:
> On 12/31/2015 5:07 PM, Marek Vasut wrote:
> > On Thursday, December 31, 2015 at 08:24:45 AM, Peng Fan wrote:
> >> From: "Ye.Li"
> >>
> >> All the i.MX6, i.MX23 and i.MX28 OTG controllers only support UTMI
> >> interface. Set to
On 22 December 2015 at 12:04, Joe Hershberger wrote:
> On Tue, Dec 22, 2015 at 12:43 AM, Bin Meng wrote:
>> In eth_current_changed(), the call to eth_get_dev() below has a side
>> effect of rotating ethernet device if uc_priv->current == NULL. This
>> is not what we want when 'ethrotate' variable
On 22 December 2015 at 12:05, Joe Hershberger wrote:
> On Tue, Dec 22, 2015 at 12:43 AM, Bin Meng wrote:
>> When 'ethrotate' variable is set to 'no' and 'ethact' variable
>> is already set to an ethernet device, we should stick to 'ethact'.
>>
>> Signed-off-by: Bin Meng
>
> Acked-by: Joe Hershbe
drivers/mtd/ubi/io.c:1354:3: error: 'dump_len' undeclared (first use in
this function)
dump_len = max_t(int, 128, len - i);
Signed-off-by: Ladislav Michl
---
drivers/mtd/ubi/io.c | 1 -
1 file changed, 1 deletion(-)
diff --git a/drivers/mtd/ubi/io.c b/drivers/mtd/ubi/io.c
index d1bdec3..0be9
On Sunday, January 03, 2016 at 09:50:30 PM, Simon Glass wrote:
> The current limit of 5 is not enough for the driver model USB tests. Really
> we should not have a limit but the driver model code still uses the
> usb_dev_desc[] array, which has a limit.
>
> Increasing the limit by 2 should not bot
On Sunday, January 03, 2016 at 09:50:31 PM, Simon Glass wrote:
> At present USB keyboards are not properly removed with driver model. Add
> the code to handle this.
>
> Signed-off-by: Simon Glass
Reviewed-by: Marek Vasut
Best regards,
Marek Vasut
___
Hi David,
On 11 December 2015 at 05:07, David Müller (ELSOFT AG)
wrote:
> Simon Glass wrote:
>
>> David are you able to move your board to driver model for i2c?
>
> To be frank, I don't know it (yet). Being a total DM novice, it is
> difficult for me to estimate the amount of effort needed to do
It is common for I2C and SPI buses to have a single-cell address and a size
of 0. These produce a warning at present. For example on snow:
__of_translate_address: Bad cell count for gpc4
__of_translate_address: Bad cell count for gpx0
__of_translate_address: Bad cell count for gpv2
__of_translate_
On 3 January 2016 at 13:52, Simon Glass wrote:
> On 22 December 2015 at 12:04, Joe Hershberger
> wrote:
>> On Tue, Dec 22, 2015 at 12:43 AM, Bin Meng wrote:
>>> In eth_current_changed(), the call to eth_get_dev() below has a side
>>> effect of rotating ethernet device if uc_priv->current == NUL
On 19 December 2015 at 15:24, Simon Glass wrote:
> Applied to u-boot-dm/next.
Also
Applied to u-boot-dm/master, thanks!
___
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
On 3 January 2016 at 13:52, Simon Glass wrote:
> On 22 December 2015 at 12:05, Joe Hershberger
> wrote:
>> On Tue, Dec 22, 2015 at 12:43 AM, Bin Meng wrote:
>>> When 'ethrotate' variable is set to 'no' and 'ethact' variable
>>> is already set to an ethernet device, we should stick to 'ethact'.
Hi,
On Sun, Jan 03, 2016 at 09:59:23AM +0100, Wolfgang Denk wrote:
> [added USB custodian to Cc:]
>
> In message <20160102211834.e49a161...@mail.nwl.cc> you wrote:
> > In order to allow for Linux properly register the integrated EHCI host,
> > we have to reset it after initialization. Without thi
On Monday, January 04, 2016 at 12:38:07 AM, Phil Sutter wrote:
> Hi,
>
> On Sun, Jan 03, 2016 at 09:59:23AM +0100, Wolfgang Denk wrote:
> > [added USB custodian to Cc:]
> >
> > In message <20160102211834.e49a161...@mail.nwl.cc> you wrote:
> > > In order to allow for Linux properly register the in
+Dirk
On Sun, Jan 3, 2016 at 1:09 AM, Tom Rini wrote:
> On Tue, Dec 22, 2015 at 11:58:01AM -0600, Joe Hershberger wrote:
>
>> A few patches that came in during the merge window and appear harmless.
>>
>> These cause no additional build warnings or errors.
>>
>> Thanks,
>> -Joe
>>
>> The following
When doing `dhcp`, there is a bad dhcp server in my network
which always reply dhcp request with yiaddr 0, which cause
uboot can not successfully get ipaddr from the good dhcp server.
But the Linux PC can get the ip address even if there is a bad
dhcp server. This patch is to fix that even if there
Hi,
On Mon, Jan 04, 2016 at 12:47:37AM +0100, Marek Vasut wrote:
> On Monday, January 04, 2016 at 12:38:07 AM, Phil Sutter wrote:
> > The bit which really was missing is the USB mode setting I smuggled in
> > along with my patch - setting the devices to host mode is sufficient for
> > Linux to suc
Hi Fabio,
On Thu, Dec 31, 2015 at 11:20 PM, Fabio Estevam wrote:
> Hi Bin,
>
> On Thu, Dec 31, 2015 at 7:32 AM, Bin Meng wrote:
>
>> I also see this behavior on ls1021atwr board. I agree with Simon, the
>> correct fix should fix the PCIe driver to return 0 instead of -EINVAL.
>
> Do you mean lik
On Thu, Dec 31, 2015 at 5:02 PM, Miao Yan wrote:
> Hi Simon,
>
> 2015-12-31 13:08 GMT+08:00 Simon Glass :
>> Hi Maio,
>>
>> On 30 December 2015 at 19:55, Miao Yan wrote:
>>> Add a function to fix up 'cpus' node in dts files for qemu target.
>>>
>>> Signed-off-by: Miao Yan
>>> ---
>>> Changes in
On Mon, Jan 04, 2016 at 10:35:39AM +0800, Bin Meng wrote:
> +Dirk
>
> On Sun, Jan 3, 2016 at 1:09 AM, Tom Rini wrote:
> > On Tue, Dec 22, 2015 at 11:58:01AM -0600, Joe Hershberger wrote:
> >
> >> A few patches that came in during the merge window and appear harmless.
> >>
> >> These cause no addi
+Simon,
Hi Tom,
On Mon, Jan 4, 2016 at 11:46 AM, Tom Rini wrote:
> On Mon, Jan 04, 2016 at 10:35:39AM +0800, Bin Meng wrote:
>> +Dirk
>>
>> On Sun, Jan 3, 2016 at 1:09 AM, Tom Rini wrote:
>> > On Tue, Dec 22, 2015 at 11:58:01AM -0600, Joe Hershberger wrote:
>> >
>> >> A few patches that came in
On Mon, Dec 28, 2015 at 1:16 AM, Maxime Ripard
wrote:
> On Wed, Dec 23, 2015 at 12:14:15PM +0200, Siarhei Siamashka wrote:
>> On Tue, 17 Nov 2015 15:32:30 +0100
>> Jens Kuske wrote:
>>
>> > On 16/11/15 07:26, Chen-Yu Tsai wrote:
>> > > Hi everyone,
>> > >
>> > > I got my Orange Pi PC booting U-bo
Hi Simon,
On Sun, Jan 3, 2016 at 2:50 PM, Simon Glass wrote:
> At present USB keyboards are not properly removed with driver model. Add the
> code to handle this.
>
> Signed-off-by: Simon Glass
Is this supposed to fix the crash that I was reporting details about
in the USB keyboard sandbox test
Hi Miao,
On Thu, Dec 31, 2015 at 10:55 AM, Miao Yan wrote:
> The QEMU fw_cfg interface allows the guest to retrieve various
> data information from QEMU. For example, APCI/SMBios tables, number
> of online cpus, kernel data and command line, etc.
>
> This patch adds support for QEMU fw_cfg interf
On Thu, Dec 31, 2015 at 10:55 AM, Miao Yan wrote:
> Add a cpu uclass driver for qemu. Previously, the qemu
> target gets cpu number from board dts files, which are
> manually created at compile time. This does not scale
> when more cpus are assigned to guest as the dts files
> must be modified as
On Thu, Dec 31, 2015 at 10:55 AM, Miao Yan wrote:
> Use actual CPU number, instead of maximum cpu configured,
> to allocate stack memory in 'load_sipi_vector'
>
> Signed-off-by: Miao Yan
> ---
> arch/x86/cpu/mp_init.c | 6 +++---
> 1 file changed, 3 insertions(+), 3 deletions(-)
>
Reviewed-by:
Hi Miao,
On Thu, Dec 31, 2015 at 10:55 AM, Miao Yan wrote:
> By default, ramdisk load address is defined to 0200 in
> env string. When loading bzImage to 10 (default address), there's
The default load address is 100 (16MB). See CONFIG_LOADADDR in x86-common.h
> a chance that the ram
Hi Miao,
On Thu, Dec 31, 2015 at 10:55 AM, Miao Yan wrote:
> Document the usage of 'fw' command
>
> Signed-off-by: Miao Yan
> ---
> Changes in v4:
> - limit maximum supported cpu number to 32
>
> doc/README.x86 | 35 ---
> 1 file changed, 32 insertions(+), 3 de
On Thu, Dec 31, 2015 at 10:55 AM, Miao Yan wrote:
> Rename 'find_cpu_by_apid_id' to 'find_cpu_by_apic_id'. This
> should be a typo.
>
> Signed-off-by: Miao Yan
> ---
> arch/x86/cpu/mp_init.c | 6 +++---
> 1 file changed, 3 insertions(+), 3 deletions(-)
>
Reviewed-by: Bin Meng
_
Hi Joe,
On Jan 3, 2016 9:04 PM, "Joe Hershberger" wrote:
>
> Hi Simon,
>
> On Sun, Jan 3, 2016 at 2:50 PM, Simon Glass wrote:
> > At present USB keyboards are not properly removed with driver model.
Add the
> > code to handle this.
> >
> > Signed-off-by: Simon Glass
>
> Is this supposed to fix
Hi Miao,
On Thu, Dec 31, 2015 at 10:55 AM, Miao Yan wrote:
> The fw_cfg interface provided by QEMU allow guests to retrieve various
> information
> about the system, e.g. cpu number, variaous firmware data, kernel setup, etc.
> The
> fw_cfg interface can be accessed through 3 IO ports (on x86),
This commit 4bdcbe60a142b08eefccb0e326a37ba81d3389e8 removes reset_cpu which
breaks SPL build when DEBUG macro defined.
Introudce a weak function reset_cpu to avoid build failure when
building SPL for i.MX with DEBUG enabled.
"
arch/arm/lib/built-in.o: In function `do_reset':
~/uboot/arch/arm/lib/
With DEBUG macro enabled, SPL build failure:
"
arch/arm/cpu/armv7/built-in.o: In function `reset_misc':
~/uboot/arch/arm/cpu/armv7/mx6/soc.c:406: undefined reference to
`lcdif_power_down'
scripts/Makefile.spl:244: recipe for target 'spl/u-boot-spl' failed
"
Wrap VIDEO settings with ifndef CONFIG_S
Hi Simon,
On 4 January 2016 at 01:22, Simon Glass wrote:
> Hi Jagan,
>
> On 22 December 2015 at 12:39, Joe Hershberger
> wrote:
>> Hi Simon,
>>
>> On Tue, Dec 22, 2015 at 1:14 PM, Joe Hershberger
>> wrote:
>>> Hi Simon,
>>>
>>> On Mon, Dec 21, 2015 at 9:17 PM, Joe Hershberger
>>> wrote:
The management data input/output (MDIO) requires open-drain,
i.MX7D TO1.0 ENET MDIO pin has no open drain, but TO1.1 supports
this feature. So to TO1.1, need to enable open drain by setting
bits GPR0[8:7] for TO1.1.
Signed-off-by: Peng Fan
Cc: Stefano Babic
---
arch/arm/cpu/armv7/mx7/soc.c
To TO1.0, we can not rely on finish bit to read temperature. But to
TO1.1, the issue was fixed by IC, we can rely on finish bit for
temperature reading for TO1.1.
Signed-off-by: Peng Fan
Cc: Stefano Babic
Cc: Tim Harvey
Cc: Fabio Estevam
Cc: Adrian Alonso
---
drivers/thermal/imx_thermal.c |
Hi Jagan,
On Mon, Jan 4, 2016 at 1:12 PM, Jagan Teki wrote:
> Hi Simon,
>
> On 4 January 2016 at 01:22, Simon Glass wrote:
>> Hi Jagan,
>>
>> On 22 December 2015 at 12:39, Joe Hershberger
>> wrote:
>>> Hi Simon,
>>>
>>> On Tue, Dec 22, 2015 at 1:14 PM, Joe Hershberger
>>> wrote:
Hi Simon
Add more entries for structure mxc_ccm_reg.
Signed-off-by: Peng Fan
Cc: Stefano Babic
---
arch/arm/include/asm/arch-mx6/crm_regs.h | 87
1 file changed, 87 insertions(+)
diff --git a/arch/arm/include/asm/arch-mx6/crm_regs.h
b/arch/arm/include/asm/arch-mx6/crm_
Check "Figure 19-5. BUS clock generation" of i.MX 6SoloX Applications
Processor Reference Manual and "Figure 18-5. BUS clock generation" of
i.MX 6UltraLite Applications Processor Reference Manual. If mmdc clk
sources from pll4_main_clk(pll_audio), the calculation is wrong.
Fix mmdc_ch0 clk calcula
Hello Ladislav Michl
Am 03.01.2016 um 22:05 schrieb Ladislav Michl:
drivers/mtd/ubi/io.c:1354:3: error: 'dump_len' undeclared (first use in
this function)
dump_len = max_t(int, 128, len - i);
Signed-off-by: Ladislav Michl
---
drivers/mtd/ubi/io.c | 1 -
1 file changed, 1 deletion(-)
Y
Hello Simon,
Am 29.12.2015 um 13:22 schrieb Simon Glass:
We should not return a -ve error code from command functions. Instead,
return CMD_RET_FAILURE. This avoids the "exit not allowed from main input
shell" error messages from the hush shell.
Signed-off-by: Simon Glass
---
common/cmd_i2c.
Hello Moritz,
Am 28.12.2015 um 18:47 schrieb Moritz Fischer:
Signed-off-by: Moritz Fischer
---
doc/device-tree-bindings/i2c/i2c-cdns.txt | 20
1 file changed, 20 insertions(+)
create mode 100644 doc/device-tree-bindings/i2c/i2c-cdns.txt
Looks good to me:
Acked-by: He
Hello Moritz,
Am 28.12.2015 um 18:47 schrieb Moritz Fischer:
This is a possible drop in replacement for drivers/i2c/zynq-i2c.c
Since this is cadence IP it has been renamed to cdns-i2c,
to make sense with the compatible string.
Signed-off-by: Moritz Fischer
---
drivers/i2c/Kconfig| 7 +
From: "Ye.Li"
According to the Coverity result, a unsigned int variable is used fo less-
than-zero comparison, the result is never true. Need to fix the variable
type to signed int.
Signed-off-by: Ye.Li
Signed-off-by: Peng Fan
Cc: Przemyslaw Marczak
Cc: Stefano Babic
---
board/freescale/com
Support uncompressing zImage which is larger than 8M.
Signed-off-by: Peng Fan
Cc: Peter Robinson
Cc: Volodymyr Riazantsev
Cc: Fabio Estevam
Cc: Adrian Alonso
Cc: Stefano Babic
---
include/configs/mx6_common.h | 2 ++
include/configs/mx7_common.h | 2 ++
2 files changed, 4 insertions(+)
dif
66 matches
Mail list logo
