This patchset aims to add support for the Internal RMII Ethernet PHY of the
Amlogic Meson GXL S905X SoC on the Amlogic P212 Reference board.
The Internal PHY needs a specific config then acts as a generic PHY.
Neil Armstrong (3):
net: phy: Add Amlogic Meson GXL Internal PHY support
arm: meson
The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY.
The PHY acts as a generic PHY but needs a slight configuration right
before it's configuration.
Signed-off-by: Neil Armstrong
---
drivers/net/phy/Kconfig | 3 +++
drivers/net/phy/Makefile| 1 +
drivers/net/phy/me
On Amlogic Meson GXL/GXM, supplementary ethernet configuration registers
were added to configure the internal RMII PHY interface.
Signed-off-by: Neil Armstrong
---
arch/arm/include/asm/arch-meson/gxbb.h | 3 +++
1 file changed, 3 insertions(+)
diff --git a/arch/arm/include/asm/arch-meson/gxbb.h
This patch adds support for the Internal RMII Ethernet PHY on the
Amlogic P212 Reference Board.
Signed-off-by: Neil Armstrong
---
board/amlogic/p212/p212.c | 39 ++-
configs/p212_defconfig| 4
include/configs/p212.h| 2 ++
3 files changed, 44 in
Spam detection software, running on the system "lists.denx.de",
has identified this incoming email as possible spam. The original
message has been attached to this so you can view it or label
similar future email. If you have any questions, see
@@CONTACT_ADDRESS@@ for details.
Content preview:
This patch extends pmic_bind_children prefix matching. In addition to
the node name the property regulator-name is used while trying to match
prefixes. This allows assigning different drivers to regulator nodes
named regulator@1 and regulator@10 for example.
I have discarded the idea of using other
On 10/18/2017 03:30 AM, Suneel Garapati wrote:
> On Tue, Oct 17, 2017 at 6:22 PM, Marek Vasut wrote:
>> On 10/18/2017 01:50 AM, Suneel Garapati wrote:
>>> On Tue, Oct 17, 2017 at 5:43 AM, Marek Vasut wrote:
On 10/17/2017 05:21 AM, Bin Meng wrote:
> +Marek, Tom,
Well, if the aut
where you edit it? i have same problem too
--
Sent from: http://u-boot.10912.n7.nabble.com/
___
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
Adding support for TI bandgap temperature sensor.
Also add dt support for bandgap sensor in spl.
v3:
Missed adding Reviewed-by in v2.
Faiz Abbas (2):
thermal: ti-bandgap: Add support for temperature sensor
ARM: dts: OMAP5+: Add support for bandgap sensor in SPL
arch/arm/dts/omap5-u-boot.dts
The dra7xx series of SOCs contain a temperature sensor and an
associated analog-to-digital converter (ADC) which produces
an output which is proportional to the SOC temperature.
Add support for this temperature sensor.
Signed-off-by: Faiz Abbas
Reviewed-by: Simon Glass
---
v3:
Added Reviewed-by
Mark bandgap node as uboot,dm-spl so that it can be accessed in spl
Signed-off-by: Faiz Abbas
Reviewed-by: Simon Glass
---
v3:
Added Reviewed-by comment.
arch/arm/dts/omap5-u-boot.dtsi | 4
1 file changed, 4 insertions(+)
diff --git a/arch/arm/dts/omap5-u-boot.dtsi b/arch/arm/dts/omap5-u
copy the persistent gpt binary file as it can be modified during the test
that avoid issue if the test fail: the test always restart with clean file
Acked-by: Stephen Warren
Signed-off-by: Patrick Delaunay
---
Changes in v3: None
Changes in v2:
- Split test to functional change
test/py/tests/
Add test of first and last LBA in gpt for rename and swap.
Only the name is expected to change, so test 3 columns
for part command
1: first LBA (start)
2: last LBA (end)
3: partition name
After rename, the last LBA change and it is a error in current U-Boot code
+ "first" = 0x7ff : invalid value (
add sandbox test for some gpt sub-command
- gpt read / part list : read the gpt partition created by sgdisk on host
test start, size, LBA and name output
- gpt verify : verify the gpt partition create by sgdisk on host
PS: persistent data test_gpt_disk_image.bin are udpated
Signed-off-by: Patri
+ test write for one partition on all the device (size=0)
+ test write with disk uuid and 2 partitions
Signed-off-by: Patrick Delaunay
---
This write test failed without the previous patch with the error:
"Writing GPT: Partition overlap"
gpt test are now OK on v2017.11-rc2:
./test/py/test.py -k
don't use prettyprint_part_size() in create_gpt_partitions_list()
that avoid to align offset and size to 1 MiB and increase precision for
start and size.
This patch avoid the risk to change partition size and lost data during
rename or swap.
Signed-off-by: Patrick Delaunay
---
Changes in v3: Non
the partition starting at 0x4400 is refused with overlap error:
$> gpt write mmc 0 "name=test,start=0x4400,size=0"
Writing GPT: Partition overlap
error!
even if the 0x4400 is the first available offset for LBA35 with default
value:
- MBR=LBA1
- GPT header=LBA2
- PTE= 32 LBAs (128 entry), 3 t
in the last version v2017.09, I see some regression for the command
$> gpt write mmc 0 "name=test,start=0x4400,size=0"
$> gpt write mmc 0 "name=test,size=0"
I use sandbox python test to verify if this issue is also present in
v2017.11-rc1 and when I check the log tests, I detect a other issue
fo
On 14/10/2017 16:51, Marek Vasut wrote:
On 10/02/2017 11:15 AM, Jean-Jacques Hiblot wrote:
On 22/09/2017 16:42, Jaehoon Chung wrote:
Dear JJ,
On 09/21/2017 11:29 PM, Jean-Jacques Hiblot wrote:
This series brings support for HS200 and UHS modes to the mmc core.
It has been tested with the h
On 10/18/2017 03:19 PM, Jean-Jacques Hiblot wrote:
>
>
> On 14/10/2017 16:51, Marek Vasut wrote:
>> On 10/02/2017 11:15 AM, Jean-Jacques Hiblot wrote:
>>>
>>> On 22/09/2017 16:42, Jaehoon Chung wrote:
Dear JJ,
On 09/21/2017 11:29 PM, Jean-Jacques Hiblot wrote:
> This series bri
solve data abort for the command "ums 0 ubi 0"
because result of case blk_get_device_part_str() result is OK
but with block_dev = 0 when CONFIG_CMD_UBIFS is activate and
ubi volume is mounted
Signed-off-by: Patrick Delaunay
---
cmd/usb_mass_storage.c | 2 +-
1 file changed, 1 insertion(+), 1 de
Currently when a high speed SD card is connected on MX25 or MX51 boards
the following error happens:
U-Boot 2017.11-rc2 (Oct 18 2017 - 13:49:26 -0200)
CPU: Freescale i.MX51 rev3.0 at 800 MHz
Reset cause: POR
Board: MX51EVK
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - read failed
On Wed, Oct 18, 2017 at 1:57 PM, Fabio Estevam wrote:
> Currently when a high speed SD card is connected on MX25 or MX51 boards
> the following error happens:
>
> U-Boot 2017.11-rc2 (Oct 18 2017 - 13:49:26 -0200)
>
> CPU: Freescale i.MX51 rev3.0 at 800 MHz
> Reset cause: POR
> Board: MX51EVK
> D
Hi Fabio,
On 18/10/2017 at 17:57, Fabio Estevam wrote:
> Currently when a high speed SD card is connected on MX25 or MX51 boards
> the following error happens:
>
> U-Boot 2017.11-rc2 (Oct 18 2017 - 13:49:26 -0200)
>
> CPU: Freescale i.MX51 rev3.0 at 800 MHz
> Reset cause: POR
> Board: MX51EVK
If the compared memory areas match the return value should be 0.
We should not use the unrelated constant EFI_ST_SUCCESS.
Signed-off-by: Heinrich Schuchardt
---
v4
no change
v3
new patch split off
---
lib/efi_selftest/efi_selftest_util.c | 2 +-
1 file changed, 1 insertion(+), 1
A test is added that verifies that the watchdog timer actually
causes a reboot upon timeout. The test is only executed on
request using
setenv efi_selftest watchdog reboot
bootefi selftest
Signed-off-by: Heinrich Schuchardt
---
v4
no change
v3
correct comments
v2
Environment variable efi_selftest is passed as load options
to the selftest application. It is used to select a single
test to be executed.
The load options are an UTF8 string. Yet I decided to keep
the name propertiy of the tests as char[] to reduce code
size.
Special value 'list' displays a lis
The patch series is centered on implementing the SetWatchdogTimer
boottime service. Two tests are supplied. One that checks that
resetting the watchdog timer saves from a reboot. The other
checks that the watchdog timer actually leads to a reset.
Both are covered by Python test cases.
A test for E
Where ulong or unsigned long are used to hold an EFI status
code we should consistenly use efi_status_t.
Signed-off-by: Heinrich Schuchardt
---
v4
fix indentation
v3
new patch
---
cmd/bootefi.c | 18 +-
1 file changed, 9 insertions(+), 9 deletions(-)
diff --git a
Currently we pass bootefi_device_path and bootefi_image_path as
device and image path without initializing them. They may carry
values from previous calls to bootefi.
With the patch the variables are initialized valid dummy values.
Signed-off-by: Heinrich Schuchardt
---
v4
no change
v3
The watchdog is initialized with a 5 minute timeout period.
It can be reset by SetWatchdogTimer.
It is stopped by ExitBoottimeServices.
Signed-off-by: Heinrich Schuchardt
---
v4
no change
v3
add a constant for 1s to 100ns conversion
v2
code comments updated
---
cmd/bootef
To avoid a forward declaration move efi_search_obj before
all protocol services functions.
Signed-off-by: Heinrich Schuchardt
---
v4
no change
v3
no change
v2
no change
---
lib/efi_loader/efi_boottime.c | 41 +
1 file changed,
Provide a conversion function from utf8 to utf16.
Add missing #include in include/charset.h.
Remove superfluous #include in lib/charset.c.
Signed-off-by: Heinrich Schuchardt
---
v3
no change
v2
new patch
---
include/charset.h | 15 +++
lib/charset.c | 57 ++
The test verifies that resetting the watchdog timer ensures
that it is not called during the timeout period.
Testing that the watchdog timer actually executes a reset
would require a test outside the efi_selftest framework.
Signed-off-by: Heinrich Schuchardt
---
v4
no change
v3
n
Move duplicate code to the new function efi_st_do_tests.
Suggested-by: Alexander Graf
Signed-off-by: Heinrich Schuchardt
---
v4
new patch
---
lib/efi_selftest/efi_selftest.c | 71 -
1 file changed, 42 insertions(+), 29 deletions(-)
diff --git a/l
The following services are tested:
OutputString, TestString, SetAttribute.
Signed-off-by: Heinrich Schuchardt
---
v4
fix build flags
v3
new patch
---
lib/efi_selftest/Makefile | 3 ++
lib/efi_selftest/efi_selftest_textoutput.c | 53 ++
After executing bootefi selftest
* restore GD
* unlink the load image handle
* return 0 or 1 and not a truncated efi_status_t.
Signed-off-by: Heinrich Schuchardt
---
v4
no change
v3
new patch split off
---
cmd/bootefi.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
di
Make a comment line easier to read.
Signed-off-by: Heinrich Schuchardt
---
v4
no change
v3
no change
v2
no change
---
test/py/tests/test_efi_loader.py | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/test/py/tests/test_efi_loader.py b/test/py/tests/test
Use a define to detect double inclusion of efi_loader.h.
Signed-off-by: Heinrich Schuchardt
---
v4
no change
v3
no change
v2
new patch
---
include/efi_loader.h | 7 ++-
1 file changed, 6 insertions(+), 1 deletion(-)
diff --git a/include/efi_loader.h b/include/efi_loa
Use environment variable bootargs used as load options
for bootefi payloads.
Signed-off-by: Heinrich Schuchardt
---
v4
no change
v3
new patch split off
---
cmd/bootefi.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/cmd/bootefi.c b/cmd/bootefi.c
index 40834f3899..ff659fc0
The parent_handle of the loaded image must be set.
Set the system table.
Signed-off-by: Heinrich Schuchardt
---
v4
no change
v3
new patch
---
lib/efi_loader/efi_boottime.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/lib/efi_loader/efi_boottime.c b/lib/efi_loader/efi_boo
Remove superfluous spaces.
Signed-off-by: Heinrich Schuchardt
---
v4
no change
v3
new patch split off
---
lib/efi_selftest/efi_selftest.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/lib/efi_selftest/efi_selftest.c b/lib/efi_selftest/efi_selftest.c
inde
On 18/10/2017 at 18:13, Benoît Thébaudeau wrote:
> Hi Fabio,
>
> On 18/10/2017 at 17:57, Fabio Estevam wrote:
>> Currently when a high speed SD card is connected on MX25 or MX51 boards
>> the following error happens:
>>
>> U-Boot 2017.11-rc2 (Oct 18 2017 - 13:49:26 -0200)
>>
>> CPU: Freescale i.
Clear environment variable efi_selftest before executing the
default tests.
Provide a test verifying that the EFI watchdog
reboots the system upon timeout.
The test depends on CONFIG_CMD_EFI_SELFTEST=y.
Signed-off-by: Heinrich Schuchardt
---
v4
no change
v3
no change
v2
On Wed, Oct 18, 2017 at 04:03:21PM +0200, Patrick Delaunay wrote:
> solve data abort for the command "ums 0 ubi 0"
> because result of case blk_get_device_part_str() result is OK
> but with block_dev = 0 when CONFIG_CMD_UBIFS is activate and
> ubi volume is mounted
>
> Signed-off-by: Patrick Dela
Hi Benoît,
On Wed, Oct 18, 2017 at 2:13 PM, Benoît Thébaudeau wrote:
> You could stress-test the SD read/write accesses from U-Boot. Does it occur
> with
> all HS cards?
I am not able to run a stress-test because all SD card accesses fail.
It happens with all HS cards I tested with.
> You ca
On 10/15/2017 03:21 PM, Fabio Estevam wrote:
> From: Fabio Estevam
>
> Inside setup_sata() there is a cpu type check, so there is no need to
> do this check in the board file.
>
> Signed-off-by: Fabio Estevam
> ---
> board/udoo/udoo.c | 3 +--
> 1 file changed, 1 insertion(+), 2 deletions(-)
>
On 10/15/2017 03:21 PM, Fabio Estevam wrote:
> From: Fabio Estevam
>
> Inside setup_sata() there is a cpu type check, so there is no need to
> do this check in the board file.
>
> This also brings the benefit to allowing setup_sata() to be called for the
> mx6qp wandboard variant.
>
> Signed-of
Hi Fabio,
On 18/10/2017 at 18:40, Fabio Estevam wrote:
> On Wed, Oct 18, 2017 at 2:13 PM, Benoît Thébaudeau wrote:
>> You can try to set the drive strength of all the eSDHC pads to high or max
>> (for
>
> Looks like the eSDHC pins do not have drive strength control, only
> PKE, PUE, PUS and SRE
On 10/18/2017 07:11 AM, Patrick Delaunay wrote:
don't use prettyprint_part_size() in create_gpt_partitions_list()
that avoid to align offset and size to 1 MiB and increase precision for
start and size.
This patch avoid the risk to change partition size and lost data during
rename or swap.
All t
Hi Benoît ,
On Wed, Oct 18, 2017 at 2:56 PM, Benoît Thébaudeau wrote:
> I can tell you what to use for imx25pdk if you give me the pads used by the
> eSDHC instance in question here.
mx25pdk uses the POR default IOMUX settings for sdhc1:
static const iomux_v3_cfg_t sdhc1_pads[] = {
NEW_PAD_CTR
On Tue, Oct 17, 2017 at 07:20:04PM +0530, Jagan Teki wrote:
> Hi Tom,
>
> Please pull this PR.
>
> thanks!
> Jagan.
>
> The following changes since commit 10509987285515b0a969c39ef7374fea3545851b:
>
> spi: fsl_qspi: Copy 16 byte aligned data in TX FIFO (2017-09-25 15:45:15
> +0530)
>
> are
On Wed, Oct 18, 2017 at 05:11:52PM +0530, Faiz Abbas wrote:
> The dra7xx series of SOCs contain a temperature sensor and an
> associated analog-to-digital converter (ADC) which produces
> an output which is proportional to the SOC temperature.
> Add support for this temperature sensor.
>
> Signed
On Tue, Oct 17, 2017 at 04:29:13PM +0200, Heiko Schocher wrote:
> Hello Tom,
>
> please pull from u-boot-i2c master
>
> The following changes since commit eb0044db392247aa1c43e29f2703418d5668018a:
>
> Prepare v2017.11-rc2 (2017-10-16 21:40:56 -0400)
>
> are available in the git repository at
On Wed, Oct 18, 2017 at 05:11:53PM +0530, Faiz Abbas wrote:
> Mark bandgap node as uboot,dm-spl so that it can be accessed in spl
>
> Signed-off-by: Faiz Abbas
> Reviewed-by: Simon Glass
Reviewed-by: Tom Rini
--
Tom
signature.asc
Description: PGP signature
Hi Fabio,
On Wed, Oct 18, 2017 at 7:35 PM, Fabio Estevam wrote:
> On Wed, Oct 18, 2017 at 2:56 PM, Benoît Thébaudeau wrote:
>
>> I can tell you what to use for imx25pdk if you give me the pads used by the
>> eSDHC instance in question here.
>
> mx25pdk uses the POR default IOMUX settings for sdh
Hi Benoît,
On Wed, Oct 18, 2017 at 6:10 PM, Benoît Thébaudeau
wrote:
> Can you try with this?
>
> static const iomux_v3_cfg_t sdhc1_pads[] = {
> NEW_PAD_CTRL(MX25_PAD_SD1_CMD__SD1_CMD, PAD_CTL_PUS_47K_UP |
> PAD_CTL_SRE_FAST),
> NEW_PAD_CTRL(MX25_PAD_SD1_CLK__SD1_CLK, PAD_CTL_SRE_FAST),
> NEW_P
Hi Simon,
> On some boards where the spi flash is not reset during warm reboot,
> the chip has to be manually set into 3-byte address mode.
>
> Signed-off-by: Simon Goldschmidt
Reviewed-by: Lukasz Majewski
> ---
> drivers/mtd/spi/sf_internal.h | 2 ++
> drivers/mtd/spi/spi_flash.c | 53
>
On 10/18/2017 06:27 PM, Tom Rini wrote:
> On Wed, Oct 18, 2017 at 04:03:21PM +0200, Patrick Delaunay wrote:
>
>> solve data abort for the command "ums 0 ubi 0"
>> because result of case blk_get_device_part_str() result is OK
>> but with block_dev = 0 when CONFIG_CMD_UBIFS is activate and
>> ubi vo
With latest codes on mainstream master, Intel Galileo board does not
boot unfortunately. Git biset leads to b383d6c0 "bootstage: Convert
to use malloc()".
Disable bootstage support to make it boot again. The root cause needs
to be investigated however.
Fixes: b383d6c0 ("bootstage: Convert to use
It was observed that when booting Linux kernel on Intel Cherry Hill
board, unexpected crash happens quite randomly. Sometimes kernel
just oops, while sometimes kernel throws MCE errors and hangs:
mce: [Hardware Error]: Machine check events logged
mce: [Hardware Error]: CPU 0: Machine Check: 0
Some Intel FSP (like Braswell) does SPI lock-down during the call
to fsp_notify(INIT_PHASE_BOOT). But before SPI lock-down is done,
it's bootloader's responsibility to configure the SPI controller's
opcode registers properly otherwise SPI controller driver doesn't
know how to communicate with the S
On some platforms (eg: Braswell), the FSP will not produce the
graphics info HOB unless you plug some cables to the display
interface (eg: HDMI) on the board. Add such notes in the FSP
video driver.
Signed-off-by: Bin Meng
---
arch/x86/lib/fsp/fsp_graphics.c | 4
1 file changed, 4 insertio
Imply does not work for a Kconfig choice. Update ENV_IS_IN_SPI_FLASH
to be the default one for Intel Braswell.
Signed-off-by: Bin Meng
---
arch/x86/cpu/braswell/Kconfig | 1 -
env/Kconfig | 1 +
2 files changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/x86/cpu/braswell
This reverts commit 1e6ebee667da47fd3a87839a239a7574c66f5659.
It's not appropriate to call the Intel SPI driver specific stuff in
the FSP codes. We may add a simple DTS property "intel,spi-lock-down"
and let the Intel SPI driver call these stuff instead.
Signed-off-by: Bin Meng
---
arch/x86/Kc
Intel Braswell FSP requires SPI controller settings to be locked down,
let's do this in the chrryhill.dts and remove previous Kconfig option.
Signed-off-by: Bin Meng
---
arch/x86/cpu/braswell/Kconfig | 4
arch/x86/dts/cherryhill.dts | 1 +
2 files changed, 1 insertion(+), 4 deletions(-)
In an S3 resume path, MRC cache is mandatory. Enforce the dependency
in the Kconfig.
Signed-off-by: Bin Meng
---
arch/x86/Kconfig | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index c869ae2..b2ae865 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@
The supported sleep states are generic on Intel processors. Move the
ASL definition to the common place.
Signed-off-by: Bin Meng
---
arch/x86/include/asm/{arch-baytrail => }/acpi/sleepstates.asl | 0
arch/x86/include/asm/arch-baytrail/acpi/platform.asl | 2 +-
arch/x86/include/asm/ar
usb tree/info commands iterate over all usb uclass devices
recursively. blk uclass child devices are created for mass storage,
treating these as usb uclass devices and referencing usb config
interface descriptors cause crash. To fix, ignore blk and usb_emul
uclass devices(sandbox) in usb_show_info
On 10/19/2017 03:22 AM, Suneel Garapati wrote:
> usb tree/info commands iterate over all usb uclass devices
> recursively. blk uclass child devices are created for mass storage,
> treating these as usb uclass devices and referencing usb config
> interface descriptors cause crash. To fix, ignore blk
Spam detection software, running on the system "lists.denx.de",
has identified this incoming email as possible spam. The original
message has been attached to this so you can view it or label
similar future email. If you have any questions, see
@@CONTACT_ADDRESS@@ for details.
Content preview:
Hi Fabio
> -Original Message-
> From: Fabio Estevam [mailto:feste...@gmail.com]
> Sent: Tuesday, October 17, 2017 12:15 AM
> To: Peng Fan
> Cc: Stefano Babic ; Fabio Estevam
> ; U-Boot-Denx
> Subject: Re: [U-Boot] [PATCH V2] imx: mx6slevk: fix mmc breakage
>
> Hi Peng,
>
> Subject shou
Since DM_USB enabled, no need the usb code in board file.
Signed-off-by: Peng Fan
Cc: Stefano Babic
Cc: Fabio Estevam
---
V3:
Changed title and commit log. Only cleanup the usb code.
V2:
Based on Fabio's patches:
1. https://patchwork.ozlabs.org/patch/825464/
2. https://patchwork.ozlabs.
On Wed, Oct 18, 2017 at 6:39 PM, Marek Vasut wrote:
> On 10/19/2017 03:22 AM, Suneel Garapati wrote:
>> usb tree/info commands iterate over all usb uclass devices
>> recursively. blk uclass child devices are created for mass storage,
>> treating these as usb uclass devices and referencing usb conf
On Fri, Oct 13, 2017 at 7:09 PM, Stefan Roese wrote:
> On 12.10.2017 14:07, Bin Meng wrote:
>>
>> It was observed that when booting a Ubuntu 16.04 kernel, doing ACPI
>> S3 suspend/resume sometimes causes the Ubuntu kernel hang forever.
>> The issue is however not reproduced with a kernel built fro
On Fri, Oct 13, 2017 at 7:09 PM, Stefan Roese wrote:
> On 12.10.2017 14:07, Bin Meng wrote:
>>
>> This is only needed when graphics console is used. For kernel with
>> native graphics driver, this can be turned off to speed up.
>>
>> Change this option's default to n in the Kconfig.
>>
>> Signed-o
On Fri, Oct 13, 2017 at 7:14 PM, Stefan Roese wrote:
> On 13.10.2017 10:30, Bin Meng wrote:
>>
>> Azalia configuration may be different across boards, hence it's not
>> appropriate to do that in the SoC level. Instead, let's make the
>> SoC update_fsp_azalia_configs() routine as a weak version, an
On Fri, Oct 13, 2017 at 7:14 PM, Stefan Roese wrote:
> On 13.10.2017 10:30, Bin Meng wrote:
>>
>> So far there are two copies of Azalia struct defines with one in
>> baytrail and the other one in braswell. This consolidates these
>> two into one, put it in the common place, and remove the prefix
>
On Fri, Oct 13, 2017 at 7:14 PM, Stefan Roese wrote:
> On 13.10.2017 10:30, Bin Meng wrote:
>>
>> At present we directly pass the Azalia config pointer to the FSP UPD.
>> This updates to use a function to do the stuff, like Braswell does.
>>
>> Signed-off-by: Bin Meng
>> ---
>>
>> arch/x86/cpu/
On Tue, Oct 17, 2017 at 4:51 PM, Bin Meng wrote:
> On Tue, Oct 17, 2017 at 2:09 PM, Stefan Roese wrote:
>> I've missed to add the ACPI resume support to this x86 build target.
>> This patch adds the ACPI resume support enabling S3 suspend /
>> resume.
>>
>> Signed-off-by: Stefan Roese
>> Cc: Bin
On Tue, Oct 17, 2017 at 4:52 PM, Bin Meng wrote:
> On Tue, Oct 17, 2017 at 2:08 AM, Heinrich Schuchardt
> wrote:
>> Up to now we depended on an exported variable to build u-boot.rom.
>> We should be able to specify it in the configuration file, too.
>>
>> With this patch this becomes possible us
Hi Tom,
This includes a critical bug fix for Baytrail ACPI suspend/resume and
some other minor clean ups.
The following changes since commit 6b0fea33424dcce82b6df0c6b3774601eb1ff36a:
Merge git://git.denx.de/u-boot-i2c (2017-10-18 09:32:35 -0400)
are available in the git repository at:
git:
Hello Masahiro,
Am 17.10.2017 um 15:36 schrieb Masahiro Yamada:
Historically, U-Boot added CONFIG_SYS_ prefix to user-unconfigurable
options. Somehow, this rule was not observed in some places, and
getting meaningless with Kconfig introduction where platforms can
"select" to force options. Act
Hi Heiko,
2017-10-19 13:38 GMT+09:00 Heiko Schocher :
> Hello Masahiro,
>
>
> Am 17.10.2017 um 15:36 schrieb Masahiro Yamada:
>>
>> Historically, U-Boot added CONFIG_SYS_ prefix to user-unconfigurable
>> options. Somehow, this rule was not observed in some places, and
>> getting meaningless with
84 matches
Mail list logo