RE: [asterisk-users] X100P - zttools says red status
The card that I have got only has one port. I assume there are two versions? Thanks -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Leo Ann Boon Sent: 27 January 2007 00:58 To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] X100P - zttools says red status Charlie Grosvenor wrote: Yes the line is connected, a standard phone works fine when connected to the line. There're 2 ports on the card. Which port are you using? One of the ports is for connecting another phone in parallel to the card. Leo ___ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] X100P - zttools says red status
Charlie Grosvenor wrote: The card that I have got only has one port. I assume there are two versions? Thanks NOPE There really is only one port. two modular jacks, one marked line, which should go to the PSTN or FXS device, one with battery on it. The second, upper? port is simply in parallel, and in some modems ( can't say for sure on the X100 ) is opened when the modem goes off hook. If you have a card with only ONE modular jack, then perhaps you don't really have an X100?? Remember the X100 is really a simple WinModem that has a specific chipset that the Zaptel driver was written for, If you were to remove it and place it in a Windows machine with the proper drivers, you would have a run of the mill 56K dial up modem Red alarm in the X100 means it doesn't see battery from the PSTN -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Leo Ann Boon Sent: 27 January 2007 00:58 To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] X100P - zttools says red status Charlie Grosvenor wrote: Yes the line is connected, a standard phone works fine when connected to the line. There're 2 ports on the card. Which port are you using? One of the ports is for connecting another phone in parallel to the card. Leo ___ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] X100P - zttools says red status
On Fri, Jan 26, 2007 at 08:42:36PM -, Charlie Grosvenor wrote: I have an X100P which I have set up as per the guidelines: http://www.x100p.com/support/doc/quick_start_fxo.php The card is recognized by the system: Zaptel Version: 1.4.0 Echo Canceller: MG2 Configuration == Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. However when I run zttools it says its status is red, which my understanding of is that it has not detected the line. I am in the uk and using a standard BT line (with ADSL). Any suggestions? Is the line plugged in? Can you connect a standard phone to the same line? -- Tzafrir Cohen icq#16849755jabber:[EMAIL PROTECTED] +972-50-7952406 mailto:[EMAIL PROTECTED] http://www.xorcom.com iax:[EMAIL PROTECTED]/tzafrir ___ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
RE: [asterisk-users] X100P - zttools says red status
Yes the line is connected, a standard phone works fine when connected to the line. Thanks -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Tzafrir Cohen Sent: 26 January 2007 23:45 To: asterisk-users@lists.digium.com Subject: Re: [asterisk-users] X100P - zttools says red status On Fri, Jan 26, 2007 at 08:42:36PM -, Charlie Grosvenor wrote: I have an X100P which I have set up as per the guidelines: http://www.x100p.com/support/doc/quick_start_fxo.php The card is recognized by the system: Zaptel Version: 1.4.0 Echo Canceller: MG2 Configuration == Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. However when I run zttools it says its status is red, which my understanding of is that it has not detected the line. I am in the uk and using a standard BT line (with ADSL). Any suggestions? Is the line plugged in? Can you connect a standard phone to the same line? -- Tzafrir Cohen icq#16849755jabber:[EMAIL PROTECTED] +972-50-7952406 mailto:[EMAIL PROTECTED] http://www.xorcom.com iax:[EMAIL PROTECTED]/tzafrir ___ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [asterisk-users] X100P - zttools says red status
Charlie Grosvenor wrote: Yes the line is connected, a standard phone works fine when connected to the line. There're 2 ports on the card. Which port are you using? One of the ports is for connecting another phone in parallel to the card. Leo ___ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
