Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ?
need to first enter the configuration mode. I .Entry into SETTING STATUS 1) Pick up the phone, press the button of 0 ** #; 2) Screen display: ?SETUP?; Input pass: input pass word: 332808 Then will display IMPUT CON you can change the box working mode . use the command *000100#0#for set defaut ,billing mode. *000100#1#for one long tone mode *000100#2#for long tone mode Sam -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of adibar Sent: Saturday, March 11, 2006 4:55 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? Hi Dan To connect the gsm-gateway I'm using a X100P which is sufficiant and which works. But I'm exeriencing problems with the device itself. The gateway acts like a POTS for me, but according a sales-representive of CT they do use it like a phone ?!? Dialing in works fine (beside the currently missing CID). Calls are taken from ZAP and are routed internaly. I can pickup, talk and... hangup. But after hanging up the gateway starts beeping like hell and requires a reset. Outgoing calls are even worse. I can dial, opposite takes the call, gateway hangs up and beeps again. Therefore... reset again. To be shure that it's neither * nor the X100P I tried the same with an old analog phone. Same result. So, you see. as I'm currently not ready to use it, I even could not think about tweaking, fine-tuning and codec-testing ;-) As soon as the tech-departement from CT comes (hopefully) back to me with a solution I'm the going to treat that box ;-) adibar On Fri, Mar 10, 2006 at 10:15:44PM +0300, [EMAIL PROTECTED] wrote: Hi adiar, Just have a few questions. Hope u can give me the answers. Well im currently having analog lines to my asterisk which is used to bridge calls from PSTN to Voip (DISA). Im facing issues with hang up supervision etc. Im thinking of bridging calls using the GSM gateway in future. Just want to know will it work well with codecs and disconnect supervision. I need g729 to work well i have low bandwdth too. Im facing issues with TDM11B + analog lines. So will the GSM gateway + TDM11B a better choice? Please some one advice.. Dan On 10/03/06, adibar [EMAIL PROTECTED] wrote: Hi I would like to say that I'm a happy user of it. But currently I'm still waiting for support from CT. My gateway is here, but it's doing nasty things, so currently I'm not a good source for information. Sorry Adibar On Fri, Mar 10, 2006 at 07:03:25PM +0300, [EMAIL PROTECTED] wrote: Hi, I wrote this thread to find someone who uses this. Please write if u r using this as i would like to clarify regarding disconnect supervision. Thanks On 08/03/06, Wireless [EMAIL PROTECTED] wrote: Does anyone have this working on 1800MHz eg TMobile or Orange in the UK and does CLID work or not? THanks Harvey - Original Message - From: Conrad Wood [EMAIL PROTECTED] To: Asterisk Users Mailing List - Non-Commercial Discussion asterisk-users@lists.digium.com Sent: Friday, February 17, 2006 1:01 AM Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? On Thu, 2006-02-16 at 23:39 +0100, adibar wrote: Hi List Is someone out there using one or more GSMgateway(s) from CyberTelecom ? Me and some friends are interested in buying some of them, but before we would like to ask, how the experiences are others have made
Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ?
pass word: 332808 Then will display IMPUT CON you can change the box working mode . use the command *000100#0#for set defaut ,billing mode. *000100#1#for one long tone mode *000100#2#for long tone mode Sam -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of adibar Sent: Saturday, March 11, 2006 4:55 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? Hi Dan To connect the gsm-gateway I'm using a X100P which is sufficiant and which works. But I'm exeriencing problems with the device itself. The gateway acts like a POTS for me, but according a sales-representive of CT they do use it like a phone ?!? Dialing in works fine (beside the currently missing CID). Calls are taken from ZAP and are routed internaly. I can pickup, talk and... hangup. But after hanging up the gateway starts beeping like hell and requires a reset. Outgoing calls are even worse. I can dial, opposite takes the call, gateway hangs up and beeps again. Therefore... reset again. To be shure that it's neither * nor the X100P I tried the same with an old analog phone. Same result. So, you see. as I'm currently not ready to use it, I even could not think about tweaking, fine-tuning and codec-testing ;-) As soon as the tech-departement from CT comes (hopefully) back to me with a solution I'm the going to treat that box ;-) adibar On Fri, Mar 10, 2006 at 10:15:44PM +0300, [EMAIL PROTECTED] wrote: Hi adiar, Just have a few questions. Hope u can give me the answers. Well im currently having analog lines to my asterisk which is used to bridge calls from PSTN to Voip (DISA). Im facing issues with hang up supervision etc. Im thinking of bridging calls using the GSM gateway in future. Just want to know will it work well with codecs and disconnect supervision. I need g729 to work well i have low bandwdth too. Im facing issues with TDM11B + analog lines. So will the GSM gateway + TDM11B a better choice? Please some one advice.. Dan On 10/03/06, adibar [EMAIL PROTECTED] wrote: Hi I would like to say that I'm a happy user of it. But currently I'm still waiting for support from CT. My gateway is here, but it's doing nasty things, so currently I'm not a good source for information. Sorry Adibar On Fri, Mar 10, 2006 at 07:03:25PM +0300, [EMAIL PROTECTED] wrote: Hi, I wrote this thread to find someone who uses this. Please write if u r using this as i would like to clarify regarding disconnect supervision. Thanks On 08/03/06, Wireless [EMAIL PROTECTED] wrote: Does anyone have this working on 1800MHz eg TMobile or Orange in the UK and does CLID work or not? THanks Harvey - Original Message - From: Conrad Wood [EMAIL PROTECTED] To: Asterisk Users Mailing List - Non-Commercial Discussion asterisk-users@lists.digium.com Sent: Friday, February 17, 2006 1:01 AM Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? On Thu, 2006-02-16 at 23:39 +0100, adibar wrote: Hi List Is someone out there using one or more GSMgateway(s) from CyberTelecom ? Me and some friends are interested in buying some of them, but before we would like to ask, how the experiences are others have made. e.g. How easy to setup ? How reliable ? How's the voice quality ? etc. I use the analogue version. it was very easy to setup
Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ?
, March 11, 2006 4:55 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? Hi Dan To connect the gsm-gateway I'm using a X100P which is sufficiant and which works. But I'm exeriencing problems with the device itself. The gateway acts like a POTS for me, but according a sales-representive of CT they do use it like a phone ?!? Dialing in works fine (beside the currently missing CID). Calls are taken from ZAP and are routed internaly. I can pickup, talk and... hangup. But after hanging up the gateway starts beeping like hell and requires a reset. Outgoing calls are even worse. I can dial, opposite takes the call, gateway hangs up and beeps again. Therefore... reset again. To be shure that it's neither * nor the X100P I tried the same with an old analog phone. Same result. So, you see. as I'm currently not ready to use it, I even could not think about tweaking, fine-tuning and codec-testing ;-) As soon as the tech-departement from CT comes (hopefully) back to me with a solution I'm the going to treat that box ;-) adibar On Fri, Mar 10, 2006 at 10:15:44PM +0300, [EMAIL PROTECTED] wrote: Hi adiar, Just have a few questions. Hope u can give me the answers. Well im currently having analog lines to my asterisk which is used to bridge calls from PSTN to Voip (DISA). Im facing issues with hang up supervision etc. Im thinking of bridging calls using the GSM gateway in future. Just want to know will it work well with codecs and disconnect supervision. I need g729 to work well i have low bandwdth too. Im facing issues with TDM11B + analog lines. So will the GSM gateway + TDM11B a better choice? Please some one advice.. Dan On 10/03/06, adibar [EMAIL PROTECTED] wrote: Hi I would like to say that I'm a happy user of it. But currently I'm still waiting for support from CT. My gateway is here, but it's doing nasty things, so currently I'm not a good source for information. Sorry Adibar On Fri, Mar 10, 2006 at 07:03:25PM +0300, [EMAIL PROTECTED] wrote: Hi, I wrote this thread to find someone who uses this. Please write if u r using this as i would like to clarify regarding disconnect supervision. Thanks On 08/03/06, Wireless [EMAIL PROTECTED] wrote: Does anyone have this working on 1800MHz eg TMobile or Orange in the UK and does CLID work or not? THanks Harvey - Original Message - From: Conrad Wood [EMAIL PROTECTED] To: Asterisk Users Mailing List - Non-Commercial Discussion asterisk-users@lists.digium.com Sent: Friday, February 17, 2006 1:01 AM Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? On Thu, 2006-02-16 at 23:39 +0100, adibar wrote: Hi List Is someone out there using one or more GSMgateway(s) from CyberTelecom ? Me and some friends are interested in buying some of them, but before we would like to ask, how the experiences are others have made. e.g. How easy to setup ? How reliable ? How's the voice quality ? etc. I use the analogue version. it was very easy to setup, essentially plug sim in and go. voice quality is good. Delivery was prompt. one caveat I found though: It doesn't seem to work with T-Mobile in UK. Linus Surgus on asterisk-biz suggested it might only be working on 900Mhz instead of - as advertised - 1800 Mhz and 900 Mhz. I am going to try an orange simcard next, because orange also uses 1800 (like t-mobile). Because of this I cannot comment
Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ?
, March 11, 2006 4:55 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? Hi Dan To connect the gsm-gateway I'm using a X100P which is sufficiant and which works. But I'm exeriencing problems with the device itself. The gateway acts like a POTS for me, but according a sales-representive of CT they do use it like a phone ?!? Dialing in works fine (beside the currently missing CID). Calls are taken from ZAP and are routed internaly. I can pickup, talk and... hangup. But after hanging up the gateway starts beeping like hell and requires a reset. Outgoing calls are even worse. I can dial, opposite takes the call, gateway hangs up and beeps again. Therefore... reset again. To be shure that it's neither * nor the X100P I tried the same with an old analog phone. Same result. So, you see. as I'm currently not ready to use it, I even could not think about tweaking, fine-tuning and codec-testing ;-) As soon as the tech-departement from CT comes (hopefully) back to me with a solution I'm the going to treat that box ;-) adibar On Fri, Mar 10, 2006 at 10:15:44PM +0300, [EMAIL PROTECTED] wrote: Hi adiar, Just have a few questions. Hope u can give me the answers. Well im currently having analog lines to my asterisk which is used to bridge calls from PSTN to Voip (DISA). Im facing issues with hang up supervision etc. Im thinking of bridging calls using the GSM gateway in future. Just want to know will it work well with codecs and disconnect supervision. I need g729 to work well i have low bandwdth too. Im facing issues with TDM11B + analog lines. So will the GSM gateway + TDM11B a better choice? Please some one advice.. Dan On 10/03/06, adibar [EMAIL PROTECTED] wrote: Hi I would like to say that I'm a happy user of it. But currently I'm still waiting for support from CT. My gateway is here, but it's doing nasty things, so currently I'm not a good source for information. Sorry Adibar On Fri, Mar 10, 2006 at 07:03:25PM +0300, [EMAIL PROTECTED] wrote: Hi, I wrote this thread to find someone who uses this. Please write if u r using this as i would like to clarify regarding disconnect supervision. Thanks On 08/03/06, Wireless [EMAIL PROTECTED] wrote: Does anyone have this working on 1800MHz eg TMobile or Orange in the UK and does CLID work or not? THanks Harvey - Original Message - From: Conrad Wood [EMAIL PROTECTED] To: Asterisk Users Mailing List - Non-Commercial Discussion asterisk-users@lists.digium.com Sent: Friday, February 17, 2006 1:01 AM Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? On Thu, 2006-02-16 at 23:39 +0100, adibar wrote: Hi List Is someone out there using one or more GSMgateway(s) from CyberTelecom ? Me and some friends are interested in buying some of them, but before we would like to ask, how the experiences are others have made. e.g. How easy to setup ? How reliable ? How's the voice quality ? etc. I use the analogue version. it was very easy to setup, essentially plug sim in and go. voice quality is good. Delivery was prompt. one caveat I found though: It doesn't seem to work with T-Mobile in UK. Linus Surgus on asterisk-biz suggested it might only be working on 900Mhz instead of - as advertised - 1800 Mhz and 900 Mhz. I am going to try an orange simcard next, because orange also uses 1800 (like t-mobile). Because of this I cannot comment
Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ?
Thanks Adibar, (sorry List:-) You have at least an offer. The only thing I've got so far was a promiss to have a decision tomorrow .For a month now, tomorrow is every day after the day before tomorrow. However, I hope, that in order to keep it's good reputation CyberTelecom will consider FREE OF CHARGE EXCHANGE of the useless GSM boxes or do immediate refund or something. Let's see... Cheers, Benchev On Wednesday 26 April 2006 01:17, adibar wrote: Hi Benchev News from the front. Sam is kinda offering me an exchange of my box. But I should return it to him at my cost ;-) Last word is not spoken yet on that, cause I'm really not amused on this ;-) Keeping you in loop. Greets Adibar On Mon, Mar 27, 2006 at 10:05:01AM +0300, Benchev wrote: Actually I've got five, but the first one I have received around Xmas and I don't have these problems with it. I use spa3000 as FXO and the gsm gateway works seamlessly inbound, outbound, DISA, no annoying sounds, no DTMF problems. There is one problem however, the gateway does not transfer correctly the CID to the FXO(at least in my case) but this could be a sipura problem as well. Now, the other 4 seam to be a different model or something and one should be very careful ordering that thing since you never know which model you are going to receive. They are used with no-brand-name FXO/FXS ATAs but I don't think that the ATAs is the problem. Everything goes wrong when the gateway is tested as a dock-n-talk (dialing through it connected to one of the RJ11 with an ordinary phone set). First there is no DTMF recognition whatsoever, and second tha gateway does not sense the hangup and start making the noises. Hope Sam could solve the problem with the factory or exchange the goods with working ones. Benchev Outch... Four of them and not working... That hurts. How do you connect them to * ? As I'm using only one for me an X100P-FXO is sufficiant and seems to work as good as attaching a real anlog phone. Btw. I saw that www.voipsolutions.be is selling them also, but for 165.- euro On Sun, Mar 26, 2006 at 03:28:07PM +0200, Benchev wrote: Hi Adibar, Thanks very much for the answer. We are also struggling (with 4 of them :( ) and will let you know how the things develop, too, in case of success. Have a nice Sunday, Benchev Hi Benchev I'm still in contact with Sam, but currently no changes. The device is still in an unusable state for me, as it only allows one call, which results in wild-beeping on terminating the call. But I still hope, that Sam finds anywhere a tech-person who can hand me out the correct setup-information. As soon as I get it in a working state, I will let you know it ;-) Adibar On Sat, Mar 25, 2006 at 09:55:56PM +0200, Benchev wrote: Hi Adibar, Any success with the gsm gateway? I have exactly the same problem with units received this month. The codes given by Sam are not working... Please, let me know if you have discovered something. Thanks in advance, Benchev But these are the wrong instructions again. Same as those ones you sent me allready. I've got the small box for £60 The only reaction I get is if I press just *. Then the display changes to SET___. After that there is silence for about 15 seconds. Pressing any keys is only allowd up to four digits. So also the given password is to long for entering. After the 15 seconds or the four digits I get a busy-signal. No password-prompt, no LINE CON. Nada... Adibar On Sat, Mar 11, 2006 at 05:12:40AM +0800, Sam Tam wrote: Hello To solved the beeping problem you need to first enter the configuration mode. I .Entry into SETTING STATUS 1) Pick up the phone, press the button of 0 ** #; 2) Screen display: ?SETUP?; Input pass: input pass word: 332808 Then will display IMPUT CON you can change the box working mode . use the command *000100#0#for set defaut ,billing mode. *000100#1#for one long tone mode *000100#2#for long tone mode Sam -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of adibar Sent: Saturday, March 11, 2006 4:55 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? Hi Dan To connect the gsm-gateway I'm using a X100P which is sufficiant and which works. But I'm exeriencing problems with the device
Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ?
Actually I've got five, but the first one I have received around Xmas and I don't have these problems with it. I use spa3000 as FXO and the gsm gateway works seamlessly inbound, outbound, DISA, no annoying sounds, no DTMF problems. There is one problem however, the gateway does not transfer correctly the CID to the FXO(at least in my case) but this could be a sipura problem as well. Now, the other 4 seam to be a different model or something and one should be very careful ordering that thing since you never know which model you are going to receive. They are used with no-brand-name FXO/FXS ATAs but I don't think that the ATAs is the problem. Everything goes wrong when the gateway is tested as a dock-n-talk (dialing through it connected to one of the RJ11 with an ordinary phone set). First there is no DTMF recognition whatsoever, and second tha gateway does not sense the hangup and start making the noises. Hope Sam could solve the problem with the factory or exchange the goods with working ones. Benchev Outch... Four of them and not working... That hurts. How do you connect them to * ? As I'm using only one for me an X100P-FXO is sufficiant and seems to work as good as attaching a real anlog phone. Btw. I saw that www.voipsolutions.be is selling them also, but for 165.- euro On Sun, Mar 26, 2006 at 03:28:07PM +0200, Benchev wrote: Hi Adibar, Thanks very much for the answer. We are also struggling (with 4 of them :( ) and will let you know how the things develop, too, in case of success. Have a nice Sunday, Benchev Hi Benchev I'm still in contact with Sam, but currently no changes. The device is still in an unusable state for me, as it only allows one call, which results in wild-beeping on terminating the call. But I still hope, that Sam finds anywhere a tech-person who can hand me out the correct setup-information. As soon as I get it in a working state, I will let you know it ;-) Adibar On Sat, Mar 25, 2006 at 09:55:56PM +0200, Benchev wrote: Hi Adibar, Any success with the gsm gateway? I have exactly the same problem with units received this month. The codes given by Sam are not working... Please, let me know if you have discovered something. Thanks in advance, Benchev But these are the wrong instructions again. Same as those ones you sent me allready. I've got the small box for £60 The only reaction I get is if I press just *. Then the display changes to SET___. After that there is silence for about 15 seconds. Pressing any keys is only allowd up to four digits. So also the given password is to long for entering. After the 15 seconds or the four digits I get a busy-signal. No password-prompt, no LINE CON. Nada... Adibar On Sat, Mar 11, 2006 at 05:12:40AM +0800, Sam Tam wrote: Hello To solved the beeping problem you need to first enter the configuration mode. I .Entry into SETTING STATUS 1) Pick up the phone, press the button of 0 ** #; 2) Screen display: ?SETUP?; Input pass: input pass word: 332808 Then will display IMPUT CON you can change the box working mode . use the command *000100#0#for set defaut ,billing mode. *000100#1#for one long tone mode *000100#2#for long tone mode Sam -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of adibar Sent: Saturday, March 11, 2006 4:55 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? Hi Dan To connect the gsm-gateway I'm using a X100P which is sufficiant and which works. But I'm exeriencing problems with the device itself. The gateway acts like a POTS for me, but according a sales-representive of CT they do use it like a phone ?!? Dialing in works fine (beside the currently missing CID). Calls are taken from ZAP and are routed internaly. I can pickup, talk and... hangup. But after hanging up the gateway starts beeping like hell and requires a reset. Outgoing calls are even worse. I can dial, opposite takes the call, gateway hangs up and beeps again. Therefore... reset again. To be shure that it's neither * nor the X100P I tried the same with an old analog phone. Same result. So, you see. as I'm currently not ready to use it, I even could not think about tweaking, fine-tuning and codec-testing ;-) As soon as the tech-departement from CT comes (hopefully) back to me with a solution I'm the going to treat that box ;-) adibar On Fri, Mar 10, 2006 at 10:15:44PM +0300, [EMAIL PROTECTED] wrote: Hi
Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ?
Hi Adibar, Any success with the gsm gateway? I have exactly the same problem with units received this month. The codes given by Sam are not working... Please, let me know if you have discovered something. Thanks in advance, Benchev But these are the wrong instructions again. Same as those ones you sent me allready. I've got the small box for £60 The only reaction I get is if I press just *. Then the display changes to SET___. After that there is silence for about 15 seconds. Pressing any keys is only allowd up to four digits. So also the given password is to long for entering. After the 15 seconds or the four digits I get a busy-signal. No password-prompt, no LINE CON. Nada... Adibar On Sat, Mar 11, 2006 at 05:12:40AM +0800, Sam Tam wrote: Hello To solved the beeping problem you need to first enter the configuration mode. I .Entry into SETTING STATUS 1) Pick up the phone, press the button of 0 ** #; 2) Screen display: ?SETUP?; Input pass: input pass word: 332808 Then will display IMPUT CON you can change the box working mode . use the command *000100#0#for set defaut ,billing mode. *000100#1#for one long tone mode *000100#2#for long tone mode Sam -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of adibar Sent: Saturday, March 11, 2006 4:55 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? Hi Dan To connect the gsm-gateway I'm using a X100P which is sufficiant and which works. But I'm exeriencing problems with the device itself. The gateway acts like a POTS for me, but according a sales-representive of CT they do use it like a phone ?!? Dialing in works fine (beside the currently missing CID). Calls are taken from ZAP and are routed internaly. I can pickup, talk and... hangup. But after hanging up the gateway starts beeping like hell and requires a reset. Outgoing calls are even worse. I can dial, opposite takes the call, gateway hangs up and beeps again. Therefore... reset again. To be shure that it's neither * nor the X100P I tried the same with an old analog phone. Same result. So, you see. as I'm currently not ready to use it, I even could not think about tweaking, fine-tuning and codec-testing ;-) As soon as the tech-departement from CT comes (hopefully) back to me with a solution I'm the going to treat that box ;-) adibar On Fri, Mar 10, 2006 at 10:15:44PM +0300, [EMAIL PROTECTED] wrote: Hi adiar, Just have a few questions. Hope u can give me the answers. Well im currently having analog lines to my asterisk which is used to bridge calls from PSTN to Voip (DISA). Im facing issues with hang up supervision etc. Im thinking of bridging calls using the GSM gateway in future. Just want to know will it work well with codecs and disconnect supervision. I need g729 to work well i have low bandwdth too. Im facing issues with TDM11B + analog lines. So will the GSM gateway + TDM11B a better choice? Please some one advice.. Dan On 10/03/06, adibar [EMAIL PROTECTED] wrote: Hi I would like to say that I'm a happy user of it. But currently I'm still waiting for support from CT. My gateway is here, but it's doing nasty things, so currently I'm not a good source for information. Sorry Adibar On Fri, Mar 10, 2006 at 07:03:25PM +0300, [EMAIL PROTECTED] wrote: Hi, I wrote this thread to find someone who uses this. Please write if u r using this as i would like to clarify regarding disconnect supervision. Thanks On 08/03/06, Wireless [EMAIL PROTECTED] wrote: Does anyone have this working on 1800MHz eg TMobile or Orange in the UK and does CLID work or not? THanks Harvey - Original Message - From: Conrad Wood [EMAIL PROTECTED] To: Asterisk Users Mailing List - Non-Commercial Discussion asterisk-users@lists.digium.com Sent: Friday, February 17, 2006 1:01 AM Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? On Thu, 2006-02-16 at 23:39 +0100, adibar wrote: Hi List Is someone out there using one or more GSMgateway(s) from CyberTelecom ? Me and some friends are interested in buying some of them, but before we would like to ask, how the experiences are others have made. e.g. How easy to setup ? How reliable ? How's the voice quality ? etc. I use the analogue version. it was very easy to setup, essentially plug sim in and go. voice quality is good. Delivery was prompt. one caveat I found though
Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ?
Hi, I wrote this thread to find someone who uses this. Please write if u r using this as i would like to clarify regarding disconnect supervision. Thanks On 08/03/06, Wireless [EMAIL PROTECTED] wrote: Does anyone have this working on 1800MHz eg TMobile or Orange in the UK and does CLID work or not? THanks Harvey - Original Message - From: Conrad Wood [EMAIL PROTECTED] To: Asterisk Users Mailing List - Non-Commercial Discussion asterisk-users@lists.digium.com Sent: Friday, February 17, 2006 1:01 AM Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? On Thu, 2006-02-16 at 23:39 +0100, adibar wrote: Hi List Is someone out there using one or more GSMgateway(s) from CyberTelecom ? Me and some friends are interested in buying some of them, but before we would like to ask, how the experiences are others have made. e.g. How easy to setup ? How reliable ? How's the voice quality ? etc. I use the analogue version. it was very easy to setup, essentially plug sim in and go. voice quality is good. Delivery was prompt. one caveat I found though: It doesn't seem to work with T-Mobile in UK. Linus Surgus on asterisk-biz suggested it might only be working on 900Mhz instead of - as advertised - 1800 Mhz and 900 Mhz. I am going to try an orange simcard next, because orange also uses 1800 (like t-mobile). Because of this I cannot comment on the reliabilty yet. -- conrad ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ?
Hi I would like to say that I'm a happy user of it. But currently I'm still waiting for support from CT. My gateway is here, but it's doing nasty things, so currently I'm not a good source for information. Sorry Adibar On Fri, Mar 10, 2006 at 07:03:25PM +0300, [EMAIL PROTECTED] wrote: Hi, I wrote this thread to find someone who uses this. Please write if u r using this as i would like to clarify regarding disconnect supervision. Thanks On 08/03/06, Wireless [EMAIL PROTECTED] wrote: Does anyone have this working on 1800MHz eg TMobile or Orange in the UK and does CLID work or not? THanks Harvey - Original Message - From: Conrad Wood [EMAIL PROTECTED] To: Asterisk Users Mailing List - Non-Commercial Discussion asterisk-users@lists.digium.com Sent: Friday, February 17, 2006 1:01 AM Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? On Thu, 2006-02-16 at 23:39 +0100, adibar wrote: Hi List Is someone out there using one or more GSMgateway(s) from CyberTelecom ? Me and some friends are interested in buying some of them, but before we would like to ask, how the experiences are others have made. e.g. How easy to setup ? How reliable ? How's the voice quality ? etc. I use the analogue version. it was very easy to setup, essentially plug sim in and go. voice quality is good. Delivery was prompt. one caveat I found though: It doesn't seem to work with T-Mobile in UK. Linus Surgus on asterisk-biz suggested it might only be working on 900Mhz instead of - as advertised - 1800 Mhz and 900 Mhz. I am going to try an orange simcard next, because orange also uses 1800 (like t-mobile). Because of this I cannot comment on the reliabilty yet. -- conrad ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users -- This message has been scanned and dangerous content has been removed by our MailScanner. This includes all executables. If the transfer of executables is desired please consider to send them as a zip-file, which is allowed to pass the checks, but which will be scanned for viruses. Please be sure to keep your local Antivirus up-to-date, as this message is no guarantee that all viruses have been removed. -- ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ?
Hi adiar, Just have a few questions. Hope u can give me the answers. Well im currently having analog lines to my asterisk which is used to bridge calls from PSTN to Voip (DISA). Im facing issues with hang up supervision etc. Im thinking of bridging calls using the GSM gateway in future. Just want to know will it work well with codecs and disconnect supervision. I need g729 to work well i have low bandwdth too. Im facing issues with TDM11B + analog lines. So will the GSM gateway + TDM11B a better choice? Please some one advice.. Dan On 10/03/06, adibar [EMAIL PROTECTED] wrote: Hi I would like to say that I'm a happy user of it. But currently I'm still waiting for support from CT. My gateway is here, but it's doing nasty things, so currently I'm not a good source for information. Sorry Adibar On Fri, Mar 10, 2006 at 07:03:25PM +0300, [EMAIL PROTECTED] wrote: Hi, I wrote this thread to find someone who uses this. Please write if u r using this as i would like to clarify regarding disconnect supervision. Thanks On 08/03/06, Wireless [EMAIL PROTECTED] wrote: Does anyone have this working on 1800MHz eg TMobile or Orange in the UK and does CLID work or not? THanks Harvey - Original Message - From: Conrad Wood [EMAIL PROTECTED] To: Asterisk Users Mailing List - Non-Commercial Discussion asterisk-users@lists.digium.com Sent: Friday, February 17, 2006 1:01 AM Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? On Thu, 2006-02-16 at 23:39 +0100, adibar wrote: Hi List Is someone out there using one or more GSMgateway(s) from CyberTelecom ? Me and some friends are interested in buying some of them, but before we would like to ask, how the experiences are others have made. e.g. How easy to setup ? How reliable ? How's the voice quality ? etc. I use the analogue version. it was very easy to setup, essentially plug sim in and go. voice quality is good. Delivery was prompt. one caveat I found though: It doesn't seem to work with T-Mobile in UK. Linus Surgus on asterisk-biz suggested it might only be working on 900Mhz instead of - as advertised - 1800 Mhz and 900 Mhz. I am going to try an orange simcard next, because orange also uses 1800 (like t-mobile). Because of this I cannot comment on the reliabilty yet. -- conrad ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users -- This message has been scanned and dangerous content has been removed by our MailScanner. This includes all executables. If the transfer of executables is desired please consider to send them as a zip-file, which is allowed to pass the checks, but which will be scanned for viruses. Please be sure to keep your local Antivirus up-to-date, as this message is no guarantee that all viruses have been removed. -- ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ?
Hi Dan To connect the gsm-gateway I'm using a X100P which is sufficiant and which works. But I'm exeriencing problems with the device itself. The gateway acts like a POTS for me, but according a sales-representive of CT they do use it like a phone ?!? Dialing in works fine (beside the currently missing CID). Calls are taken from ZAP and are routed internaly. I can pickup, talk and... hangup. But after hanging up the gateway starts beeping like hell and requires a reset. Outgoing calls are even worse. I can dial, opposite takes the call, gateway hangs up and beeps again. Therefore... reset again. To be shure that it's neither * nor the X100P I tried the same with an old analog phone. Same result. So, you see. as I'm currently not ready to use it, I even could not think about tweaking, fine-tuning and codec-testing ;-) As soon as the tech-departement from CT comes (hopefully) back to me with a solution I'm the going to treat that box ;-) adibar On Fri, Mar 10, 2006 at 10:15:44PM +0300, [EMAIL PROTECTED] wrote: Hi adiar, Just have a few questions. Hope u can give me the answers. Well im currently having analog lines to my asterisk which is used to bridge calls from PSTN to Voip (DISA). Im facing issues with hang up supervision etc. Im thinking of bridging calls using the GSM gateway in future. Just want to know will it work well with codecs and disconnect supervision. I need g729 to work well i have low bandwdth too. Im facing issues with TDM11B + analog lines. So will the GSM gateway + TDM11B a better choice? Please some one advice.. Dan On 10/03/06, adibar [EMAIL PROTECTED] wrote: Hi I would like to say that I'm a happy user of it. But currently I'm still waiting for support from CT. My gateway is here, but it's doing nasty things, so currently I'm not a good source for information. Sorry Adibar On Fri, Mar 10, 2006 at 07:03:25PM +0300, [EMAIL PROTECTED] wrote: Hi, I wrote this thread to find someone who uses this. Please write if u r using this as i would like to clarify regarding disconnect supervision. Thanks On 08/03/06, Wireless [EMAIL PROTECTED] wrote: Does anyone have this working on 1800MHz eg TMobile or Orange in the UK and does CLID work or not? THanks Harvey - Original Message - From: Conrad Wood [EMAIL PROTECTED] To: Asterisk Users Mailing List - Non-Commercial Discussion asterisk-users@lists.digium.com Sent: Friday, February 17, 2006 1:01 AM Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? On Thu, 2006-02-16 at 23:39 +0100, adibar wrote: Hi List Is someone out there using one or more GSMgateway(s) from CyberTelecom ? Me and some friends are interested in buying some of them, but before we would like to ask, how the experiences are others have made. e.g. How easy to setup ? How reliable ? How's the voice quality ? etc. I use the analogue version. it was very easy to setup, essentially plug sim in and go. voice quality is good. Delivery was prompt. one caveat I found though: It doesn't seem to work with T-Mobile in UK. Linus Surgus on asterisk-biz suggested it might only be working on 900Mhz instead of - as advertised - 1800 Mhz and 900 Mhz. I am going to try an orange simcard next, because orange also uses 1800 (like t-mobile). Because of this I cannot comment on the reliabilty yet. -- conrad ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users -- This message has been scanned and dangerous content has been removed by our MailScanner. This includes all executables. If the transfer of executables is desired please consider to send them as a zip-file, which is allowed to pass the checks, but which will be scanned for viruses. Please be sure to keep your local Antivirus up-to-date, as this message is no guarantee that all viruses have been removed. -- ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users
RE: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ?
Hello To solved the beeping problem you need to first enter the configuration mode. I .Entry into SETTING STATUS 1) Pick up the phone, press the button of 0 ** #; 2) Screen display: ?SETUP?; Input pass: input pass word: 332808 Then will display IMPUT CON you can change the box working mode . use the command *000100#0#for set defaut ,billing mode. *000100#1#for one long tone mode *000100#2#for long tone mode Sam -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of adibar Sent: Saturday, March 11, 2006 4:55 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? Hi Dan To connect the gsm-gateway I'm using a X100P which is sufficiant and which works. But I'm exeriencing problems with the device itself. The gateway acts like a POTS for me, but according a sales-representive of CT they do use it like a phone ?!? Dialing in works fine (beside the currently missing CID). Calls are taken from ZAP and are routed internaly. I can pickup, talk and... hangup. But after hanging up the gateway starts beeping like hell and requires a reset. Outgoing calls are even worse. I can dial, opposite takes the call, gateway hangs up and beeps again. Therefore... reset again. To be shure that it's neither * nor the X100P I tried the same with an old analog phone. Same result. So, you see. as I'm currently not ready to use it, I even could not think about tweaking, fine-tuning and codec-testing ;-) As soon as the tech-departement from CT comes (hopefully) back to me with a solution I'm the going to treat that box ;-) adibar On Fri, Mar 10, 2006 at 10:15:44PM +0300, [EMAIL PROTECTED] wrote: Hi adiar, Just have a few questions. Hope u can give me the answers. Well im currently having analog lines to my asterisk which is used to bridge calls from PSTN to Voip (DISA). Im facing issues with hang up supervision etc. Im thinking of bridging calls using the GSM gateway in future. Just want to know will it work well with codecs and disconnect supervision. I need g729 to work well i have low bandwdth too. Im facing issues with TDM11B + analog lines. So will the GSM gateway + TDM11B a better choice? Please some one advice.. Dan On 10/03/06, adibar [EMAIL PROTECTED] wrote: Hi I would like to say that I'm a happy user of it. But currently I'm still waiting for support from CT. My gateway is here, but it's doing nasty things, so currently I'm not a good source for information. Sorry Adibar On Fri, Mar 10, 2006 at 07:03:25PM +0300, [EMAIL PROTECTED] wrote: Hi, I wrote this thread to find someone who uses this. Please write if u r using this as i would like to clarify regarding disconnect supervision. Thanks On 08/03/06, Wireless [EMAIL PROTECTED] wrote: Does anyone have this working on 1800MHz eg TMobile or Orange in the UK and does CLID work or not? THanks Harvey - Original Message - From: Conrad Wood [EMAIL PROTECTED] To: Asterisk Users Mailing List - Non-Commercial Discussion asterisk-users@lists.digium.com Sent: Friday, February 17, 2006 1:01 AM Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? On Thu, 2006-02-16 at 23:39 +0100, adibar wrote: Hi List Is someone out there using one or more GSMgateway(s) from CyberTelecom ? Me and some friends are interested in buying some of them, but before we would like to ask, how the experiences are others have made. e.g. How easy to setup ? How reliable ? How's the voice quality ? etc. I use the analogue version. it was very easy to setup, essentially plug sim in and go. voice quality is good. Delivery was prompt. one caveat I found though: It doesn't seem to work with T-Mobile in UK. Linus Surgus on asterisk-biz suggested it might only be working on 900Mhz instead of - as advertised - 1800 Mhz and 900 Mhz. I am going to try an orange simcard next, because orange also uses 1800 (like t-mobile). Because of this I cannot comment on the reliabilty yet. -- conrad ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation provided by Easynews.com
Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ?
Sorry Sam But these are the wrong instructions again. Same as those ones you sent me allready. I've got the small box for £60 The only reaction I get is if I press just *. Then the display changes to SET___. After that there is silence for about 15 seconds. Pressing any keys is only allowd up to four digits. So also the given password is to long for entering. After the 15 seconds or the four digits I get a busy-signal. No password-prompt, no LINE CON. Nada... Adibar On Sat, Mar 11, 2006 at 05:12:40AM +0800, Sam Tam wrote: Hello To solved the beeping problem you need to first enter the configuration mode. I .Entry into SETTING STATUS 1) Pick up the phone, press the button of 0 ** #; 2) Screen display: ?SETUP?; Input pass: input pass word: 332808 Then will display IMPUT CON you can change the box working mode . use the command *000100#0#for set defaut ,billing mode. *000100#1#for one long tone mode *000100#2#for long tone mode Sam -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of adibar Sent: Saturday, March 11, 2006 4:55 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? Hi Dan To connect the gsm-gateway I'm using a X100P which is sufficiant and which works. But I'm exeriencing problems with the device itself. The gateway acts like a POTS for me, but according a sales-representive of CT they do use it like a phone ?!? Dialing in works fine (beside the currently missing CID). Calls are taken from ZAP and are routed internaly. I can pickup, talk and... hangup. But after hanging up the gateway starts beeping like hell and requires a reset. Outgoing calls are even worse. I can dial, opposite takes the call, gateway hangs up and beeps again. Therefore... reset again. To be shure that it's neither * nor the X100P I tried the same with an old analog phone. Same result. So, you see. as I'm currently not ready to use it, I even could not think about tweaking, fine-tuning and codec-testing ;-) As soon as the tech-departement from CT comes (hopefully) back to me with a solution I'm the going to treat that box ;-) adibar On Fri, Mar 10, 2006 at 10:15:44PM +0300, [EMAIL PROTECTED] wrote: Hi adiar, Just have a few questions. Hope u can give me the answers. Well im currently having analog lines to my asterisk which is used to bridge calls from PSTN to Voip (DISA). Im facing issues with hang up supervision etc. Im thinking of bridging calls using the GSM gateway in future. Just want to know will it work well with codecs and disconnect supervision. I need g729 to work well i have low bandwdth too. Im facing issues with TDM11B + analog lines. So will the GSM gateway + TDM11B a better choice? Please some one advice.. Dan On 10/03/06, adibar [EMAIL PROTECTED] wrote: Hi I would like to say that I'm a happy user of it. But currently I'm still waiting for support from CT. My gateway is here, but it's doing nasty things, so currently I'm not a good source for information. Sorry Adibar On Fri, Mar 10, 2006 at 07:03:25PM +0300, [EMAIL PROTECTED] wrote: Hi, I wrote this thread to find someone who uses this. Please write if u r using this as i would like to clarify regarding disconnect supervision. Thanks On 08/03/06, Wireless [EMAIL PROTECTED] wrote: Does anyone have this working on 1800MHz eg TMobile or Orange in the UK and does CLID work or not? THanks Harvey - Original Message - From: Conrad Wood [EMAIL PROTECTED] To: Asterisk Users Mailing List - Non-Commercial Discussion asterisk-users@lists.digium.com Sent: Friday, February 17, 2006 1:01 AM Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? On Thu, 2006-02-16 at 23:39 +0100, adibar wrote: Hi List Is someone out there using one or more GSMgateway(s) from CyberTelecom ? Me and some friends are interested in buying some of them, but before we would like to ask, how the experiences are others have made. e.g. How easy to setup ? How reliable ? How's the voice quality ? etc. I use the analogue version. it was very easy to setup, essentially plug sim in and go. voice quality is good. Delivery was prompt. one caveat I found though: It doesn't seem to work with T-Mobile in UK. Linus Surgus on asterisk-biz suggested it might only be working on 900Mhz instead of - as advertised - 1800 Mhz and 900 Mhz. I am going to try an orange simcard next, because orange also uses 1800 (like t-mobile). Because of this I cannot comment on the reliabilty yet
Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ?
Thanks to Sam adibar, Well seeing all these reactions i can't be positive on this. Well i do have another choice btw. Its the 'Dock n Talk' sold by www.voxilla.com. Has anybody done with that.. ? This is a bit costlier than the gateway and ofcource. We need to use the phone itself to connect but for my purpose i guess it will do. Just worried about the hangup supervision and the codecs support. Well the plus is that it has bluetooth support so its not necessary to have the wires always. So if somebody has a done with it well i would be pleased to hear your comments. Thanks Dan On 11/03/06, adibar [EMAIL PROTECTED] wrote: Sorry Sam But these are the wrong instructions again. Same as those ones you sent me allready. I've got the small box for £60 The only reaction I get is if I press just *. Then the display changes to SET___. After that there is silence for about 15 seconds. Pressing any keys is only allowd up to four digits. So also the given password is to long for entering. After the 15 seconds or the four digits I get a busy-signal. No password-prompt, no LINE CON. Nada... Adibar On Sat, Mar 11, 2006 at 05:12:40AM +0800, Sam Tam wrote: Hello To solved the beeping problem you need to first enter the configuration mode. I .Entry into SETTING STATUS 1) Pick up the phone, press the button of 0 ** #; 2) Screen display: ?SETUP?; Input pass: input pass word: 332808 Then will display IMPUT CON you can change the box working mode . use the command *000100#0#for set defaut ,billing mode. *000100#1#for one long tone mode *000100#2#for long tone mode Sam -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of adibar Sent: Saturday, March 11, 2006 4:55 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? Hi Dan To connect the gsm-gateway I'm using a X100P which is sufficiant and which works. But I'm exeriencing problems with the device itself. The gateway acts like a POTS for me, but according a sales-representive of CT they do use it like a phone ?!? Dialing in works fine (beside the currently missing CID). Calls are taken from ZAP and are routed internaly. I can pickup, talk and... hangup. But after hanging up the gateway starts beeping like hell and requires a reset. Outgoing calls are even worse. I can dial, opposite takes the call, gateway hangs up and beeps again. Therefore... reset again. To be shure that it's neither * nor the X100P I tried the same with an old analog phone. Same result. So, you see. as I'm currently not ready to use it, I even could not think about tweaking, fine-tuning and codec-testing ;-) As soon as the tech-departement from CT comes (hopefully) back to me with a solution I'm the going to treat that box ;-) adibar On Fri, Mar 10, 2006 at 10:15:44PM +0300, [EMAIL PROTECTED] wrote: Hi adiar, Just have a few questions. Hope u can give me the answers. Well im currently having analog lines to my asterisk which is used to bridge calls from PSTN to Voip (DISA). Im facing issues with hang up supervision etc. Im thinking of bridging calls using the GSM gateway in future. Just want to know will it work well with codecs and disconnect supervision. I need g729 to work well i have low bandwdth too. Im facing issues with TDM11B + analog lines. So will the GSM gateway + TDM11B a better choice? Please some one advice.. Dan On 10/03/06, adibar [EMAIL PROTECTED] wrote: Hi I would like to say that I'm a happy user of it. But currently I'm still waiting for support from CT. My gateway is here, but it's doing nasty things, so currently I'm not a good source for information. Sorry Adibar On Fri, Mar 10, 2006 at 07:03:25PM +0300, [EMAIL PROTECTED] wrote: Hi, I wrote this thread to find someone who uses this. Please write if u r using this as i would like to clarify regarding disconnect supervision. Thanks On 08/03/06, Wireless [EMAIL PROTECTED] wrote: Does anyone have this working on 1800MHz eg TMobile or Orange in the UK and does CLID work or not? THanks Harvey - Original Message - From: Conrad Wood [EMAIL PROTECTED] To: Asterisk Users Mailing List - Non-Commercial Discussion asterisk-users@lists.digium.com Sent: Friday, February 17, 2006 1:01 AM Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? On Thu, 2006-02-16 at 23:39 +0100, adibar wrote: Hi List Is someone out there using one or more GSMgateway(s) from CyberTelecom ? Me and some friends are interested in buying some of them
Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ?
Does anyone have this working on 1800MHz eg TMobile or Orange in the UK and does CLID work or not? THanks Harvey - Original Message - From: Conrad Wood [EMAIL PROTECTED] To: Asterisk Users Mailing List - Non-Commercial Discussion asterisk-users@lists.digium.com Sent: Friday, February 17, 2006 1:01 AM Subject: Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ? On Thu, 2006-02-16 at 23:39 +0100, adibar wrote: Hi List Is someone out there using one or more GSMgateway(s) from CyberTelecom ? Me and some friends are interested in buying some of them, but before we would like to ask, how the experiences are others have made. e.g. How easy to setup ? How reliable ? How's the voice quality ? etc. I use the analogue version. it was very easy to setup, essentially plug sim in and go. voice quality is good. Delivery was prompt. one caveat I found though: It doesn't seem to work with T-Mobile in UK. Linus Surgus on asterisk-biz suggested it might only be working on 900Mhz instead of - as advertised - 1800 Mhz and 900 Mhz. I am going to try an orange simcard next, because orange also uses 1800 (like t-mobile). Because of this I cannot comment on the reliabilty yet. -- conrad ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Re: [Asterisk-Users] Anyone using the GSMgateway from CyberTelecom ?
On Thu, 2006-02-16 at 23:39 +0100, adibar wrote: Hi List Is someone out there using one or more GSMgateway(s) from CyberTelecom ? Me and some friends are interested in buying some of them, but before we would like to ask, how the experiences are others have made. e.g. How easy to setup ? How reliable ? How's the voice quality ? etc. I use the analogue version. it was very easy to setup, essentially plug sim in and go. voice quality is good. Delivery was prompt. one caveat I found though: It doesn't seem to work with T-Mobile in UK. Linus Surgus on asterisk-biz suggested it might only be working on 900Mhz instead of - as advertised - 1800 Mhz and 900 Mhz. I am going to try an orange simcard next, because orange also uses 1800 (like t-mobile). Because of this I cannot comment on the reliabilty yet. -- conrad ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users