Re: [OSL | CCIE_Voice] SNR Issue
I will do the lab today and will try again and let you know how it goes but yes I was using LSRG, I'll test with only one gw. thanks for your reply. On Fri, Feb 5, 2010 at 10:24 PM, Otto Sanchez o...@ipexpert.com wrote: Hi Arun, How long does it takes for the call to reach the rd number once you call the 5002 device? There shouldn't be any other delay other than the delay before ringing timer parameter to route the call to the rd number, Since the rerouting css is used to route both calls, the only difference I see here is that you could be using a rp with LRG configuration and the calls might be routed slightly different depending on the origin (whether 1002 calls 5002 or 5002 is sending the call to the rd number), if that's the case, please isolate the problem and configure a different rp with the corresponding rd number within a new partition, and point it to the hq gw or rl containing only hq rg gateways, in consequence change the rerouting css to a new one containing only the new created pt, Also, did you restart the servers?, configured everything from scratch?, etc, Thanks, On Fri, Feb 5, 2010 at 12:37 AM, Arun Kumar arunv...@gmail.com wrote: Hi All, Any clue will be very helpful on this, during lab 5C I made it working but after that its not working anymore every time same issue, please let me know what to check. Thanks Arun On Thu, Feb 4, 2010 at 11:59 PM, Arun Kumar arunv...@gmail.com wrote: Hi All, I run into this SNR issue: wired thing is that I can send calls to Mobile after hitting the mobility softkey and when I call from mobile line to BR1 Ph2 I see caller id as 5002 (HQ Phone 2) and when I hangup on mobile able to pickup from the desk phone but when I call the desk phone my mobile don't rings same time (Delay Before Ringing Timer = 0) every time I need to hit the mobility softkey only any clue to look into this ? Thanks Arun -- Regards, Otto Sanchez CCIE #25592 (Voice) Support Engineer - IPexpert, Inc. URL: http://www.IPexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] Callmanager install on esx problem
I running into an issue where my pub install is succesful but can't log into the console with the admin password I set during install. I've even run pwrecovery and reset the password but it isn't working. Anybody else see this happening? -- Sent from my mobile device ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Callmanager install on esx problem
I've had this happen right after a fresh install. I think it may still be doing something in the background because after a while, 30 min or so, I am able to log in via cli. Sent while mobile. On Feb 6, 2010, at 7:54, Scott ODonnell scott.odonn...@gmail.com wrote: I running into an issue where my pub install is succesful but can't log into the console with the admin password I set during install. I've even run pwrecovery and reset the password but it isn't working. Anybody else see this happening? -- Sent from my mobile device ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com http://slash128.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] Phone models in per branch in PL
Hello, Is there a current list somewhere? The proctor guide for Vol2Lab1 (section 1.1) says Phone 2 at each of the locations are 7962 phones while the Volume_2_Labs_1-4_Tables.doc shows 7961 for BR1Ph2, 7960 for BR2Ph2, and 7961 for HQPh2. Are 61s interchangeable with 62s here? Thanks. - tnn314.wordpress.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] MGCP Gateway Problem
Hey everyone, I wanted see if anyone had any ideas as to what may be wrong here. I have set up the MGCP gateway correctly as far as I can tell. It is registered with CUCM. Attached is the GW's config as well as show ccm-manager, show isdn status and the call routing elements. Everything configuration wise seems to be working. I have a registered status in CUCM and on the GW. Everything seems pretty standard with the routing elements. I have repeatedly done a no mgcp, mgcp to restart the mgcp process. I have physically unplugged the t1 cable to restart it. I have deleted and reconfigured the GW in CUCM as well as on the GW itself. I changed the Stop Routing on Unallocated Number Service Parameter to False (which I know probably isn't effecting anything related to this). I've restarted and/or activated/deactivated all of the various related feature services. I'm sure there's more I've done as I've been trying to figure this out for almost two days. Also, the debug isdn q931 isn't producing any output, which is odd to me. I keep getting a fast busy whenever I dial any numbers. I don't have access to the PSTN router's configuration, however I know it was working as I was able to make phone calls to it when I first got here, but now that I've done my own configuration it is not working anymore. Also, one of the engineers who set it up verified the configuration for me. Please help! It is very much appreciated. J Jeff Price Network Consulting Engineer - Unified Communications Practice jeffp...@cisco.com mailto:jeffp...@cisco.com Phone: 408-525-8293 Mobile: 408-204-4510 Cisco Systems, Inc. 170 West Tasman Drive, San Jose, CA 95134-1706 USA Cisco home page http://www.cisco.com/ Think before you print. This email may contain confidential and privileged material for the sole use of the intended recipient. Any review, use, distribution or disclosure by others is strictly prohibited. If you are not the intended recipient (or authorized to receive for the recipient), please contact the sender by reply email and delete all copies of this message. For corporate legal information go to: http://www.cisco.com/web/about/doing_business/legal/cri/index.html http://www.cisco.com/web/about/doing_business/legal/cri/index.html image001.jpgimage002.jpgimage003.gifversion 12.4 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname R1 ! boot-start-marker boot system flash:c2800nm-adventerprisek9-mz.124-24.T.bin boot-end-marker ! logging message-counter syslog enable password 7 110A1A0C12 ! no aaa new-model network-clock-participate wic 0 ! dot11 syslog ip source-route ! ! ip cef ! ! no ipv6 cef ! multilink bundle-name authenticated ! ! ! ! isdn switch-type primary-ni ! ! voice-card 0 ! ! ! ! ! archive log config hidekeys ! ! ! ! ! controller T1 0/0/0 pri-group timeslots 1-6,24 service mgcp ! controller T1 0/0/1 ! ! ! ! ! interface GigabitEthernet0/0 description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$ no ip address duplex auto speed auto ! interface GigabitEthernet0/0.102 encapsulation dot1Q 102 native ip address 172.21.51.196 255.255.255.224 ! interface GigabitEthernet0/0.150 encapsulation dot1Q 150 ip address 10.5.100.1 255.255.255.0 ! interface GigabitEthernet0/0.250 encapsulation dot1Q 250 ip address 10.5.200.1 255.255.255.0 ip helper-address 172.21.51.204 ! interface GigabitEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial0/0/0:23 no ip address encapsulation hdlc isdn switch-type primary-ni isdn incoming-voice voice isdn bind-l3 ccm-manager no cdp enable ! interface Serial0/1/0 no ip address encapsulation frame-relay IETF tx-ring-limit 128 tx-queue-limit 128 serial restart-delay 0 frame-relay lmi-type ansi ! interface Serial0/1/0.1 point-to-point ip address 162.5.101.1 255.255.255.0 ip ospf mtu-ignore frame-relay interface-dlci 201 ! interface Serial0/1/0.2 point-to-point ip address 162.5.102.1 255.255.255.0 ip ospf mtu-ignore frame-relay interface-dlci 202 ! router ospf 1 log-adjacency-changes network 10.5.100.0 0.0.0.255 area 0 network 10.5.200.0 0.0.0.255 area 0 network 162.5.101.0 0.0.0.255 area 0 network 162.5.102.0 0.0.0.255 area 0 network 172.5.100.0 0.0.0.255 area 0 network 172.21.51.193 0.0.0.0 area 0 network 172.21.51.0 0.0.0.255 area 0 ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 172.21.51.193 ip http server no ip http secure-server ! ! ! ! ! ! ! ! ! control-plane ! ! ! voice-port 0/0/0:23 ! ccm-manager redundant-host 172.21.51.204 ccm-manager mgcp no ccm-manager fax protocol cisco ccm-manager music-on-hold ccm-manager config server 172.21.51.205 ccm-manager config ! mgcp mgcp call-agent 172.21.51.205 2427 service-type mgcp version 0.1 mgcp dtmf-relay voip codec all mode out-of-band mgcp modem passthrough voip mode nse mgcp package-capability rtp-package mgcp package-capability
Re: [OSL | CCIE_Voice] MGCP Gateway Problem
Jeff, If debug q931 isn't producing output and everything appears to be registered right I'd assume that you have an issue with your phone/line CSS, route patterns, route list, route group, etc. Have you tried resetting the Route Group? Have you tried the dialed number analyzer to see where CUCM thinks the calls should be going for a DN in the particular CSS in use, if anywhere? DNA will tell you if you have a failure in your design, but it won't tell you to go reset the Route Group / Gateway etc. -Jeff On Sat, Feb 6, 2010 at 3:44 PM, Jeff Price (jeffpric) jeffp...@cisco.comwrote: Hey everyone, I wanted see if anyone had any ideas as to what may be wrong here. I have set up the MGCP gateway correctly as far as I can tell. It is registered with CUCM. Attached is the GW’s config as well as show ccm-manager, show isdn status and the call routing elements. Everything configuration wise seems to be working. I have a registered status in CUCM and on the GW. Everything seems pretty standard with the routing elements. I have repeatedly done a no mgcp, mgcp to restart the mgcp process. I have physically unplugged the t1 cable to restart it. I have deleted and reconfigured the GW in CUCM as well as on the GW itself. I changed the “Stop Routing on Unallocated Number” Service Parameter to False (which I know probably isn’t effecting anything related to this). I’ve restarted and/or activated/deactivated all of the various related feature services. I’m sure there’s more I’ve done as I’ve been trying to figure this out for almost two days. Also, the debug isdn q931 isn’t producing any output, which is odd to me. I keep getting a fast busy whenever I dial any numbers. I don’t have access to the PSTN router’s configuration, however I know it was working as I was able to make phone calls to it when I first got here, but now that I’ve done my own configuration it is not working anymore. Also, one of the engineers who set it up verified the configuration for me. Please help! It is very much appreciated. J [image: http://www.cisco.com/cisco/web/UK/images/emails/signaturetool/the_human_network_logo.jpg] *Jeff Price** Network Consulting Engineer - Unified Communications Practice* * * jeffp...@cisco.com Phone: *408-525-8293* Mobile: *408-204-4510* ** *Cisco Systems, Inc.* 170 West Tasman Drive, San Jose, CA 95134-1706 USA Cisco home page http://www.cisco.com/ [image: http://www.cisco.com/cisco/web/UK/images/emails/signaturetool/welcome_to_human_network_lo.jpg] [image: http://www.cisco.com/global/EMEA/brand/signature/capital/green.gif]Think before you print. This email may contain confidential and privileged material for the sole use of the intended recipient. Any review, use, distribution or disclosure by others is strictly prohibited. If you are not the intended recipient (or authorized to receive for the recipient), please contact the sender by reply email and delete all copies of this message. For corporate legal information go to: http://www.cisco.com/web/about/doing_business/legal/cri/index.html ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com image002.jpgimage003.gifimage001.jpg___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Callmanager install on esx problem
With the admin password or the OS password? Try both. I've confused myself here in the past only to realize I transposed what I thought each of them were. On Sat, Feb 6, 2010 at 10:54 AM, Scott ODonnell scott.odonn...@gmail.comwrote: I running into an issue where my pub install is succesful but can't log into the console with the admin password I set during install. I've even run pwrecovery and reset the password but it isn't working. Anybody else see this happening? -- Sent from my mobile device ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] PSTN Router question
Good evening. I am working on Lab 2 from the 4 day instructor led calls this evening (EST) and when I call from the BR2-LON line I get the following from the PSTN router. I am dailling 77353002. I get a fast busy after 7735. I can not call 011442077353003 either. I get a fast busy at the the second 3. Any thoughts. I don't want to reconfigure the PSTN router. I don't think we are supposed to. Thank you, Jefferson --More-- Feb 7 01:28:46.731: //-1//DPM/dpAssociateIncomingPeerCore: Calling Number=02077354765, Called Number=, Voice-Interface=0x486363D8, Timeout=TRUE, Peer Encap Type=ENCAP_VOICE, Peer Search Type=PEER_TYPE_VOICE, Peer Info Type=DIALPEER_INFO_SPEECH Feb 7 01:28:46.731: //-1//DPM/dpAssociateIncomingPeerCore: Result=Success(0) after DP_MATCH_ORIGINATE; Incoming Dial-peer=20004 Feb 7 01:28:48.291: //-1/F88A661B80A7/DPM/dpMatchPeersCore: Calling Number=, Called Number=7, Peer Info Type=DIALPEER_INFO_SPEECH Feb 7 01:28:48.291: //-1/F88A661B80A7/DPM/dpMatchPeersCore: Match Rule=DP_MATCH_DEST; Called Number=7 Feb 7 01:28:48.291: //-1/F88A661B80A7/DPM/dpMatchPeersCore: Result=Partial Matches(1) after DP_MATCH_DEST Feb 7 01:28:48.291: //-1/F88A661B80A7/DPM/dpMatchPeersMoreArg: Result=MORE_DIGITS_NEEDED(1) Feb 7 01:28:49.319: //-1/F88A661B80A7/DPM/dpMatchPeersCore: Calling Number=, Called Number=77, Peer Info Type=DIALPEER_INFO_SPEECH Feb 7 01:28:49.319: //-1/F88A661B80A7/DPM/dpMatchPeersCore: Match Rule=DP_MATCH_DEST; Called Number=77 Feb 7 01:28:49.319: //-1/F88A661B80A7/DPM/dpMatchPeersCore: Result=Partial Matches(1) after DP_MATCH_DEST Feb 7 01:28:49.319: //-1/F88A661B80A7/DPM/dpMatchPeersMoreArg: Result=MORE_DIGITS_NEEDED(1) Feb 7 01:28:51.019: //-1/F88A661B80A7/DPM/dpMatchPeersCore: Calling Number=, Called Number=773, Peer Info Type=DIALPEER_INFO_SPEECH Feb 7 01:28:51.019: //-1/F88A661B80A7/DPM/dpMatchPeersCore: Match Rule=DP_MATCH_DEST; Called Number=773 Feb 7 01:28:51.019: //-1/F88A661B80A7/DPM/dpMatchPeersCore: No Outgoing Dial-peer Is Matched; Result=NO_MATCH(-1) Feb 7 01:28:51.019: //-1/F88A661B80A7/DPM/dpMatchPeersMoreArg: Result=NO_MATCH(-1) ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
