[OSL | CCIE_Voice] CME/CUE - MWI Unsolicited
Hi All, In CUE Unsolicited MWI method mwi not working for sip phone working for sccp phone. Getting the following error message debug ccsip sip 481 Call leg/Transaction does not exit In the same time if we configured the MWI under the Voice Register Dn it's working fine. Is the default behaviour of unsolicited method ? We are using 7942 phones CME is 7.0 Thanks ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] UCCX Prompt
Hi, If you checked all prompts in CCX and didn't find it's probably not there :) The only default prompt I know which ends with will be with you shortly is BACD's en_bacd_allagentsbusy.au Maybe that is what you are lookin for? -- Regards, Bartosz 2011/7/5 sandeep.ra...@wipro.com Hi Experts, I am looking for a prompt which says All of our representatives are busy at this time please stay on the line someone will be with you shortly The default ICD propmt plays a queue prompt which says All of our representatives are busy at this time, your call is very important to us, please stay on the onlien your call will behandled in the order it was received can you help me find out where i can find the below prompt: All of our representatives are busy at this time please stay on the line someone will be with you shortly I browsed through WFAVVID---PromptsSystem---G711ulawICD WFAVVID---PromptsSystem---G711ulawICM Both these two paths do not have the above mentioned prompt which ends with will be with you shortly Please suggest... * Please do not print this email unless it is absolutely necessary. * The information contained in this electronic message and any attachments to this message are intended for the exclusive use of the addressee(s) and may contain proprietary, confidential or privileged information. If you are not the intended recipient, you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately and destroy all copies of this message and any attachments. WARNING: Computer viruses can be transmitted via email. The recipient should check this email and any attachments for the presence of viruses. The company accepts no liability for any damage caused by any virus transmitted by this email. www.wipro.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] SHOW CDP Neighbor Error On 2811 Router HWIC-4ESW POE
Any ideas as to what would cause a Cisco 7965 not to show up in CDP when I perform the command 'Show CDP neighbor besides no cdp enable being configured on the port, or no cdp advertise-v2, or the port being shutdown? The phone is connected to a HWIC-4ESW with POE daughter card in a 2811 Router. The phone receives power, and when plugged into the other port it works fine. Relevant Config of HWIC below and router below. Any global CDP commands I could be missing or some type of static config that would cause only 1 Phone to show up? interface FastEthernet 0/1/0 (Port phone does show up in CDP neigh) switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast switchport mode access ! ! interface FastEthernet 0/1/1 (Port phone not showing up on) switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast switchport mode access ! ! interface Vlan302 description VOICE VLAN ip address 142.102.65.254 255.255.255.0 ip helper-address 142.102.64.254 ! interface Vlan402 description DATA VLAN ip address 142.202.65.254 255.255.255.0 ! ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] SHOW CDP Neighbor Error On 2811 Router HWIC-4ESW POE
I verified the Cable and the other ports and all is well. If I move the cable from port 1 to port 0 the phone boots up normally. Not really sure what else do do but use another port at this point as everything is configured the same. Here is my entire config, I have the exact config on another router and I even went through line by line to ensure that they are the same and the other router works like a champ. version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname RTR2 ! boot-start-marker boot-end-marker ! card type t1 0 0 logging message-counter syslog ! no aaa new-model network-clock-participate wic 0 ! ! ! dot11 syslog ip source-route ! ! ip cef ! ! no ip domain lookup no ipv6 cef ! multilink bundle-name authenticated ! ! ! ! isdn switch-type primary-ni ! ! ! voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip no supplementary-service h225-notify cid-update fax protocol cisco ! ! ! voice class codec 1 codec preference 1 g711ulaw codec preference 2 g729r8 ! ! ! ! voice class h323 1 h225 timeout tcp establish 3 ! ! ! ! ! ! ! ! ! ! ! voice translation-rule 1 rule 1 /^415888\(1...$\)/ /\1/ ! voice translation-rule 7 rule 1 /^1...$/ /888\0/ type any subscriber rule 2 /^5...$/ /408777\0/ type any national ! voice translation-rule 70 rule 1 // // type any subscriber ! voice translation-rule 111 rule 1 /^1...$/ /415888\0/ type any international ! voice translation-rule 112 rule 1 // // type any international ! voice translation-rule 911 rule 1 /^1...$/ /415888\0/ type any subscriber ! voice translation-rule 912 rule 1 // // type any subscriber ! ! voice translation-profile 4DigitDNIS translate called 1 ! voice translation-profile 911 translate calling 911 translate called 912 ! voice translation-profile InternationalDANI translate calling 111 translate called 112 ! voice translation-profile LocalDANI translate calling 7 translate called 70 ! ! voice-card 0 ! ! ! username administrator privilege 15 password 0 ccievoice ! ! ! archive log config hidekeys ! ! controller T1 0/0/0 cablelength long 0db pri-group timeslots 1-24 ! controller T1 0/0/1 cablelength long 0db channel-group 0 timeslots 1-24 ! ! ! ! ! interface Loopback0 ip address 10.10.110.2 255.255.255.255 ip ospf network point-to-point ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/1 description BACKUP CONNECTON ip address 20.1.1.1 255.255.255.252 shutdown duplex auto speed auto ! interface FastEthernet0/1/0 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface FastEthernet0/1/1 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface FastEthernet0/1/2 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface FastEthernet0/1/3 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface Serial0/0/0:23 no ip address encapsulation hdlc isdn switch-type primary-ni isdn incoming-voice voice isdn outgoing display-ie isdn outgoing ie redirecting-number no cdp enable ! interface Serial0/0/1:0 description *DATA CONNECTION TO PSTN no ip address encapsulation frame-relay IETF fair-queue frame-relay lmi-type ansi ! interface Serial0/0/1:0.1 point-to-point description *DATA PVC TO HQ-RTR ip address 10.10.111.2 255.255.255.252 ip ospf mtu-ignore snmp trap link-status frame-relay interface-dlci 101 ! interface GigabitEthernet1/0 description **CONNECTION TO NME* ip address 20.20.20.20 255.255.255.254 shut ! interface Vlan1 no ip address ! interface Vlan302 description VOICE VLAN ip address 142.102.65.254 255.255.255.0 ip helper-address 142.102.64.254 h323-gateway voip interface h323-gateway voip bind srcaddr 142.102.65.254 ! interface Vlan402 description DATA VLAN ip address 142.202.65.254 255.255.255.0 ! router ospf 1 router-id 10.10.110.2 log-adjacency-changes network 10.0.0.0 0.255.255.255 area 0 network 142.102.65.0 0.0.0.255 area 0 network 142.202.65.0 0.0.0.255 area 0 ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 10.10.100.1 no ip http server no ip http secure-server ! ! ! nls resp-timeout 1 cpd cr-id 1 ! ! ! ! ! ! control-plane ! ! ! voice-port 0/0/0:23 translation-profile incoming 4DigitDNIS ! ccm-manager music-on-hold ! ! ! ! dial-peer voice 1 pots incoming called-number . direct-inward-dial ! dial-peer voice 911 pots translation-profile outgoing 911 destination-pattern 9%911 port 0/0/0:23 forward-digits 3 ! dial-peer voice 7 pots description LOCAL CALLING translation-profile outgoing LocalDANI destination-pattern 9[2-9].. port 0/0/0:23 ! dial-peer voice 110 pots translation-profile outgoing InternationalDANI destination-pattern 9011T port 0/0/0:23 prefix 011 ! dial-peer voice 1000
Re: [OSL | CCIE_Voice] SHOW CDP Neighbor Error On 2811 Router HWIC-4ESW POE
Is this something new on existing hardware, or new hardware/module? Does show diag show anything out of the ordinary for that HWIC module compared to the router that works correctly? It could be a bad port if this is something new. There really isn't all that much configuration to be done on an HWIC-4ESW and clean config should at least show the CDP neighbor if the interface is up and the phone boots. Earl Hough CCIE #16508 (RS/Security/Voice) -Original Message- From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Webb Posey Sent: Wednesday, July 06, 2011 1:29 PM To: ccie_voice Subject: Re: [OSL | CCIE_Voice] SHOW CDP Neighbor Error On 2811 Router HWIC-4ESW POE I verified the Cable and the other ports and all is well. If I move the cable from port 1 to port 0 the phone boots up normally. Not really sure what else do do but use another port at this point as everything is configured the same. Here is my entire config, I have the exact config on another router and I even went through line by line to ensure that they are the same and the other router works like a champ. version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname RTR2 ! boot-start-marker boot-end-marker ! card type t1 0 0 logging message-counter syslog ! no aaa new-model network-clock-participate wic 0 ! ! ! dot11 syslog ip source-route ! ! ip cef ! ! no ip domain lookup no ipv6 cef ! multilink bundle-name authenticated ! ! ! ! isdn switch-type primary-ni ! ! ! voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip no supplementary-service h225-notify cid-update fax protocol cisco ! ! ! voice class codec 1 codec preference 1 g711ulaw codec preference 2 g729r8 ! ! ! ! voice class h323 1 h225 timeout tcp establish 3 ! ! ! ! ! ! ! ! ! ! ! voice translation-rule 1 rule 1 /^415888\(1...$\)/ /\1/ ! voice translation-rule 7 rule 1 /^1...$/ /888\0/ type any subscriber rule 2 /^5...$/ /408777\0/ type any national ! voice translation-rule 70 rule 1 // // type any subscriber ! voice translation-rule 111 rule 1 /^1...$/ /415888\0/ type any international ! voice translation-rule 112 rule 1 // // type any international ! voice translation-rule 911 rule 1 /^1...$/ /415888\0/ type any subscriber ! voice translation-rule 912 rule 1 // // type any subscriber ! ! voice translation-profile 4DigitDNIS translate called 1 ! voice translation-profile 911 translate calling 911 translate called 912 ! voice translation-profile InternationalDANI translate calling 111 translate called 112 ! voice translation-profile LocalDANI translate calling 7 translate called 70 ! ! voice-card 0 ! ! ! username administrator privilege 15 password 0 ccievoice ! ! ! archive log config hidekeys ! ! controller T1 0/0/0 cablelength long 0db pri-group timeslots 1-24 ! controller T1 0/0/1 cablelength long 0db channel-group 0 timeslots 1-24 ! ! ! ! ! interface Loopback0 ip address 10.10.110.2 255.255.255.255 ip ospf network point-to-point ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/1 description BACKUP CONNECTON ip address 20.1.1.1 255.255.255.252 shutdown duplex auto speed auto ! interface FastEthernet0/1/0 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface FastEthernet0/1/1 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface FastEthernet0/1/2 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface FastEthernet0/1/3 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface Serial0/0/0:23 no ip address encapsulation hdlc isdn switch-type primary-ni isdn incoming-voice voice isdn outgoing display-ie isdn outgoing ie redirecting-number no cdp enable ! interface Serial0/0/1:0 description *DATA CONNECTION TO PSTN no ip address encapsulation frame-relay IETF fair-queue frame-relay lmi-type ansi ! interface Serial0/0/1:0.1 point-to-point description *DATA PVC TO HQ-RTR ip address 10.10.111.2 255.255.255.252 ip ospf mtu-ignore snmp trap link-status frame-relay interface-dlci 101 ! interface GigabitEthernet1/0 description **CONNECTION TO NME* ip address 20.20.20.20 255.255.255.254 shut ! interface Vlan1 no ip address ! interface Vlan302 description VOICE VLAN ip address 142.102.65.254 255.255.255.0 ip helper-address 142.102.64.254 h323-gateway voip interface h323-gateway voip bind srcaddr 142.102.65.254 ! interface Vlan402 description DATA VLAN ip address 142.202.65.254 255.255.255.0 ! router ospf 1 router-id 10.10.110.2 log-adjacency-changes network 10.0.0.0 0.255.255.255 area 0 network 142.102.65.0 0.0.0.255 area 0 network 142.202.65.0 0.0.0.255 area
Re: [OSL | CCIE_Voice] SHOW CDP Neighbor Error On 2811 Router HWIC-4ESW POE
Yeah, I am leaning towards bad port, changing it to a trunk port has no effect. The card is brand new. I heard a rumor of people running into this issue on the actual lab but I'm thinking this is hardware related. Just wanted to throw it out there in case someone knew something, but I'm thinking bad port and bad rumor. Webb On Wed, Jul 6, 2011 at 11:07 PM, Hough, Earl earl.ho...@pcmallservices.com wrote: Is this something new on existing hardware, or new hardware/module? Does show diag show anything out of the ordinary for that HWIC module compared to the router that works correctly? It could be a bad port if this is something new. There really isn't all that much configuration to be done on an HWIC-4ESW and clean config should at least show the CDP neighbor if the interface is up and the phone boots. Earl Hough CCIE #16508 (RS/Security/Voice) -Original Message- From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Webb Posey Sent: Wednesday, July 06, 2011 1:29 PM To: ccie_voice Subject: Re: [OSL | CCIE_Voice] SHOW CDP Neighbor Error On 2811 Router HWIC-4ESW POE I verified the Cable and the other ports and all is well. If I move the cable from port 1 to port 0 the phone boots up normally. Not really sure what else do do but use another port at this point as everything is configured the same. Here is my entire config, I have the exact config on another router and I even went through line by line to ensure that they are the same and the other router works like a champ. version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname RTR2 ! boot-start-marker boot-end-marker ! card type t1 0 0 logging message-counter syslog ! no aaa new-model network-clock-participate wic 0 ! ! ! dot11 syslog ip source-route ! ! ip cef ! ! no ip domain lookup no ipv6 cef ! multilink bundle-name authenticated ! ! ! ! isdn switch-type primary-ni ! ! ! voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip no supplementary-service h225-notify cid-update fax protocol cisco ! ! ! voice class codec 1 codec preference 1 g711ulaw codec preference 2 g729r8 ! ! ! ! voice class h323 1 h225 timeout tcp establish 3 ! ! ! ! ! ! ! ! ! ! ! voice translation-rule 1 rule 1 /^415888\(1...$\)/ /\1/ ! voice translation-rule 7 rule 1 /^1...$/ /888\0/ type any subscriber rule 2 /^5...$/ /408777\0/ type any national ! voice translation-rule 70 rule 1 // // type any subscriber ! voice translation-rule 111 rule 1 /^1...$/ /415888\0/ type any international ! voice translation-rule 112 rule 1 // // type any international ! voice translation-rule 911 rule 1 /^1...$/ /415888\0/ type any subscriber ! voice translation-rule 912 rule 1 // // type any subscriber ! ! voice translation-profile 4DigitDNIS translate called 1 ! voice translation-profile 911 translate calling 911 translate called 912 ! voice translation-profile InternationalDANI translate calling 111 translate called 112 ! voice translation-profile LocalDANI translate calling 7 translate called 70 ! ! voice-card 0 ! ! ! username administrator privilege 15 password 0 ccievoice ! ! ! archive log config hidekeys ! ! controller T1 0/0/0 cablelength long 0db pri-group timeslots 1-24 ! controller T1 0/0/1 cablelength long 0db channel-group 0 timeslots 1-24 ! ! ! ! ! interface Loopback0 ip address 10.10.110.2 255.255.255.255 ip ospf network point-to-point ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/1 description BACKUP CONNECTON ip address 20.1.1.1 255.255.255.252 shutdown duplex auto speed auto ! interface FastEthernet0/1/0 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface FastEthernet0/1/1 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface FastEthernet0/1/2 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface FastEthernet0/1/3 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface Serial0/0/0:23 no ip address encapsulation hdlc isdn switch-type primary-ni isdn incoming-voice voice isdn outgoing display-ie isdn outgoing ie redirecting-number no cdp enable ! interface Serial0/0/1:0 description *DATA CONNECTION TO PSTN no ip address encapsulation frame-relay IETF fair-queue frame-relay lmi-type ansi ! interface Serial0/0/1:0.1 point-to-point description *DATA PVC TO HQ-RTR ip address 10.10.111.2 255.255.255.252 ip ospf mtu-ignore snmp trap link-status frame-relay interface-dlci 101 !
Re: [OSL | CCIE_Voice] SHOW CDP Neighbor Error On 2811 Router HWIC-4ESW POE
That's where I would place my money - bad port, if you're able to use the other 3 ports no problem. I'd still compare the outputs of show diag with a router that has a fully functional module, just to make sure something there isn't being reported differently, as in firmware version, part number, etc. Earl Hough CCIE #16508 (RS/Security/Voice) -Original Message- From: Webb Posey [mailto:webbpo...@gmail.com] Sent: Wednesday, July 06, 2011 2:40 PM To: Hough, Earl Cc: ccie_voice Subject: Re: [OSL | CCIE_Voice] SHOW CDP Neighbor Error On 2811 Router HWIC-4ESW POE Yeah, I am leaning towards bad port, changing it to a trunk port has no effect. The card is brand new. I heard a rumor of people running into this issue on the actual lab but I'm thinking this is hardware related. Just wanted to throw it out there in case someone knew something, but I'm thinking bad port and bad rumor. Webb On Wed, Jul 6, 2011 at 11:07 PM, Hough, Earl earl.ho...@pcmallservices.com wrote: Is this something new on existing hardware, or new hardware/module? Does show diag show anything out of the ordinary for that HWIC module compared to the router that works correctly? It could be a bad port if this is something new. There really isn't all that much configuration to be done on an HWIC-4ESW and clean config should at least show the CDP neighbor if the interface is up and the phone boots. Earl Hough CCIE #16508 (RS/Security/Voice) -Original Message- From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Webb Posey Sent: Wednesday, July 06, 2011 1:29 PM To: ccie_voice Subject: Re: [OSL | CCIE_Voice] SHOW CDP Neighbor Error On 2811 Router HWIC-4ESW POE I verified the Cable and the other ports and all is well. If I move the cable from port 1 to port 0 the phone boots up normally. Not really sure what else do do but use another port at this point as everything is configured the same. Here is my entire config, I have the exact config on another router and I even went through line by line to ensure that they are the same and the other router works like a champ. version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname RTR2 ! boot-start-marker boot-end-marker ! card type t1 0 0 logging message-counter syslog ! no aaa new-model network-clock-participate wic 0 ! ! ! dot11 syslog ip source-route ! ! ip cef ! ! no ip domain lookup no ipv6 cef ! multilink bundle-name authenticated ! ! ! ! isdn switch-type primary-ni ! ! ! voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip no supplementary-service h225-notify cid-update fax protocol cisco ! ! ! voice class codec 1 codec preference 1 g711ulaw codec preference 2 g729r8 ! ! ! ! voice class h323 1 h225 timeout tcp establish 3 ! ! ! ! ! ! ! ! ! ! ! voice translation-rule 1 rule 1 /^415888\(1...$\)/ /\1/ ! voice translation-rule 7 rule 1 /^1...$/ /888\0/ type any subscriber rule 2 /^5...$/ /408777\0/ type any national ! voice translation-rule 70 rule 1 // // type any subscriber ! voice translation-rule 111 rule 1 /^1...$/ /415888\0/ type any international ! voice translation-rule 112 rule 1 // // type any international ! voice translation-rule 911 rule 1 /^1...$/ /415888\0/ type any subscriber ! voice translation-rule 912 rule 1 // // type any subscriber ! ! voice translation-profile 4DigitDNIS translate called 1 ! voice translation-profile 911 translate calling 911 translate called 912 ! voice translation-profile InternationalDANI translate calling 111 translate called 112 ! voice translation-profile LocalDANI translate calling 7 translate called 70 ! ! voice-card 0 ! ! ! username administrator privilege 15 password 0 ccievoice ! ! ! archive log config hidekeys ! ! controller T1 0/0/0 cablelength long 0db pri-group timeslots 1-24 ! controller T1 0/0/1 cablelength long 0db channel-group 0 timeslots 1-24 ! ! ! ! ! interface Loopback0 ip address 10.10.110.2 255.255.255.255 ip ospf network point-to-point ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/1 description BACKUP CONNECTON ip address 20.1.1.1 255.255.255.252 shutdown duplex auto speed auto ! interface FastEthernet0/1/0 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface FastEthernet0/1/1 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface FastEthernet0/1/2 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface FastEthernet0/1/3 switchport access vlan 402 switchport voice vlan 302 spanning-tree
Re: [OSL | CCIE_Voice] SHOW CDP Neighbor Error On 2811 Router HWIC-4ESW POE
If you have another router with the exact same config that passes - why not swap the 4ESW cards and see if the problem follows the 4ESW or stays with the chassis? Larry On Wed, Jul 6, 2011 at 10:29 AM, Webb Posey webbpo...@gmail.com wrote: I verified the Cable and the other ports and all is well. If I move the cable from port 1 to port 0 the phone boots up normally. Not really sure what else do do but use another port at this point as everything is configured the same. Here is my entire config, I have the exact config on another router and I even went through line by line to ensure that they are the same and the other router works like a champ. version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname RTR2 ! boot-start-marker boot-end-marker ! card type t1 0 0 logging message-counter syslog ! no aaa new-model network-clock-participate wic 0 ! ! ! dot11 syslog ip source-route ! ! ip cef ! ! no ip domain lookup no ipv6 cef ! multilink bundle-name authenticated ! ! ! ! isdn switch-type primary-ni ! ! ! voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip no supplementary-service h225-notify cid-update fax protocol cisco ! ! ! voice class codec 1 codec preference 1 g711ulaw codec preference 2 g729r8 ! ! ! ! voice class h323 1 h225 timeout tcp establish 3 ! ! ! ! ! ! ! ! ! ! ! voice translation-rule 1 rule 1 /^415888\(1...$\)/ /\1/ ! voice translation-rule 7 rule 1 /^1...$/ /888\0/ type any subscriber rule 2 /^5...$/ /408777\0/ type any national ! voice translation-rule 70 rule 1 // // type any subscriber ! voice translation-rule 111 rule 1 /^1...$/ /415888\0/ type any international ! voice translation-rule 112 rule 1 // // type any international ! voice translation-rule 911 rule 1 /^1...$/ /415888\0/ type any subscriber ! voice translation-rule 912 rule 1 // // type any subscriber ! ! voice translation-profile 4DigitDNIS translate called 1 ! voice translation-profile 911 translate calling 911 translate called 912 ! voice translation-profile InternationalDANI translate calling 111 translate called 112 ! voice translation-profile LocalDANI translate calling 7 translate called 70 ! ! voice-card 0 ! ! ! username administrator privilege 15 password 0 ccievoice ! ! ! archive log config hidekeys ! ! controller T1 0/0/0 cablelength long 0db pri-group timeslots 1-24 ! controller T1 0/0/1 cablelength long 0db channel-group 0 timeslots 1-24 ! ! ! ! ! interface Loopback0 ip address 10.10.110.2 255.255.255.255 ip ospf network point-to-point ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/1 description BACKUP CONNECTON ip address 20.1.1.1 255.255.255.252 shutdown duplex auto speed auto ! interface FastEthernet0/1/0 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface FastEthernet0/1/1 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface FastEthernet0/1/2 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface FastEthernet0/1/3 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface Serial0/0/0:23 no ip address encapsulation hdlc isdn switch-type primary-ni isdn incoming-voice voice isdn outgoing display-ie isdn outgoing ie redirecting-number no cdp enable ! interface Serial0/0/1:0 description *DATA CONNECTION TO PSTN no ip address encapsulation frame-relay IETF fair-queue frame-relay lmi-type ansi ! interface Serial0/0/1:0.1 point-to-point description *DATA PVC TO HQ-RTR ip address 10.10.111.2 255.255.255.252 ip ospf mtu-ignore snmp trap link-status frame-relay interface-dlci 101 ! interface GigabitEthernet1/0 description **CONNECTION TO NME* ip address 20.20.20.20 255.255.255.254 shut ! interface Vlan1 no ip address ! interface Vlan302 description VOICE VLAN ip address 142.102.65.254 255.255.255.0 ip helper-address 142.102.64.254 h323-gateway voip interface h323-gateway voip bind srcaddr 142.102.65.254 ! interface Vlan402 description DATA VLAN ip address 142.202.65.254 255.255.255.0 ! router ospf 1 router-id 10.10.110.2 log-adjacency-changes network 10.0.0.0 0.255.255.255 area 0 network 142.102.65.0 0.0.0.255 area 0 network 142.202.65.0 0.0.0.255 area 0 ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 10.10.100.1 no ip http server no ip http secure-server ! ! ! nls resp-timeout 1 cpd cr-id 1 ! ! ! ! ! ! control-plane ! ! ! voice-port 0/0/0:23 translation-profile incoming 4DigitDNIS ! ccm-manager music-on-hold !
Re: [OSL | CCIE_Voice] SHOW CDP Neighbor Error On 2811 Router HWIC-4ESW POE
Was the cards bought on ebay? Could be fake. On Jul 6, 2011 3:32 PM, Hough, Earl earl.ho...@pcmallservices.com wrote: That's where I would place my money - bad port, if you're able to use the other 3 ports no problem. I'd still compare the outputs of show diag with a router that has a fully functional module, just to make sure something there isn't being reported differently, as in firmware version, part number, etc. Earl Hough CCIE #16508 (RS/Security/Voice) -Original Message- From: Webb Posey [mailto:webbpo...@gmail.com] Sent: Wednesday, July 06, 2011 2:40 PM To: Hough, Earl Cc: ccie_voice Subject: Re: [OSL | CCIE_Voice] SHOW CDP Neighbor Error On 2811 Router HWIC-4ESW POE Yeah, I am leaning towards bad port, changing it to a trunk port has no effect. The card is brand new. I heard a rumor of people running into this issue on the actual lab but I'm thinking this is hardware related. Just wanted to throw it out there in case someone knew something, but I'm thinking bad port and bad rumor. Webb On Wed, Jul 6, 2011 at 11:07 PM, Hough, Earl earl.ho...@pcmallservices.com wrote: Is this something new on existing hardware, or new hardware/module? Does show diag show anything out of the ordinary for that HWIC module compared to the router that works correctly? It could be a bad port if this is something new. There really isn't all that much configuration to be done on an HWIC-4ESW and clean config should at least show the CDP neighbor if the interface is up and the phone boots. Earl Hough CCIE #16508 (RS/Security/Voice) -Original Message- From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Webb Posey Sent: Wednesday, July 06, 2011 1:29 PM To: ccie_voice Subject: Re: [OSL | CCIE_Voice] SHOW CDP Neighbor Error On 2811 Router HWIC-4ESW POE I verified the Cable and the other ports and all is well. If I move the cable from port 1 to port 0 the phone boots up normally. Not really sure what else do do but use another port at this point as everything is configured the same. Here is my entire config, I have the exact config on another router and I even went through line by line to ensure that they are the same and the other router works like a champ. version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname RTR2 ! boot-start-marker boot-end-marker ! card type t1 0 0 logging message-counter syslog ! no aaa new-model network-clock-participate wic 0 ! ! ! dot11 syslog ip source-route ! ! ip cef ! ! no ip domain lookup no ipv6 cef ! multilink bundle-name authenticated ! ! ! ! isdn switch-type primary-ni ! ! ! voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip no supplementary-service h225-notify cid-update fax protocol cisco ! ! ! voice class codec 1 codec preference 1 g711ulaw codec preference 2 g729r8 ! ! ! ! voice class h323 1 h225 timeout tcp establish 3 ! ! ! ! ! ! ! ! ! ! ! voice translation-rule 1 rule 1 /^415888\(1...$\)/ /\1/ ! voice translation-rule 7 rule 1 /^1...$/ /888\0/ type any subscriber rule 2 /^5...$/ /408777\0/ type any national ! voice translation-rule 70 rule 1 // // type any subscriber ! voice translation-rule 111 rule 1 /^1...$/ /415888\0/ type any international ! voice translation-rule 112 rule 1 // // type any international ! voice translation-rule 911 rule 1 /^1...$/ /415888\0/ type any subscriber ! voice translation-rule 912 rule 1 // // type any subscriber ! ! voice translation-profile 4DigitDNIS translate called 1 ! voice translation-profile 911 translate calling 911 translate called 912 ! voice translation-profile InternationalDANI translate calling 111 translate called 112 ! voice translation-profile LocalDANI translate calling 7 translate called 70 ! ! voice-card 0 ! ! ! username administrator privilege 15 password 0 ccievoice ! ! ! archive log config hidekeys ! ! controller T1 0/0/0 cablelength long 0db pri-group timeslots 1-24 ! controller T1 0/0/1 cablelength long 0db channel-group 0 timeslots 1-24 ! ! ! ! ! interface Loopback0 ip address 10.10.110.2 255.255.255.255 ip ospf network point-to-point ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/1 description BACKUP CONNECTON ip address 20.1.1.1 255.255.255.252 shutdown duplex auto speed auto ! interface FastEthernet0/1/0 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface FastEthernet0/1/1 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface FastEthernet0/1/2 switchport access vlan 402 switchport voice vlan 302 spanning-tree portfast ! interface
Re: [OSL | CCIE_Voice] SHOW CDP Neighbor Error On 2811 Router HWIC-4ESW POE
No its an authentic card from Cisco. The problem stayed with the router as well. I tried another card that is known working. I compared config line by line and didn't notice any differences. The IOS is the same on both 2811's as well and I have tried it in multiple slots. On Wed, Jul 6, 2011 at 3:36 PM, ccieid1ot ccieid...@gmail.com wrote: Was the cards bought on ebay? Could be fake. On Jul 6, 2011 3:32 PM, Hough, Earl earl.ho...@pcmallservices.com wrote: That's where I would place my money - bad port, if you're able to use the other 3 ports no problem. I'd still compare the outputs of show diag with a router that has a fully functional module, just to make sure something there isn't being reported differently, as in firmware version, part number, etc. Earl Hough CCIE #16508 (RS/Security/Voice) -Original Message- From: Webb Posey [mailto:webbpo...@gmail.com] Sent: Wednesday, July 06, 2011 2:40 PM To: Hough, Earl Cc: ccie_voice Subject: Re: [OSL | CCIE_Voice] SHOW CDP Neighbor Error On 2811 Router HWIC-4ESW POE Yeah, I am leaning towards bad port, changing it to a trunk port has no effect. The card is brand new. I heard a rumor of people running into this issue on the actual lab but I'm thinking this is hardware related. Just wanted to throw it out there in case someone knew something, but I'm thinking bad port and bad rumor. Webb On Wed, Jul 6, 2011 at 11:07 PM, Hough, Earl earl.ho...@pcmallservices.com wrote: Is this something new on existing hardware, or new hardware/module? Does show diag show anything out of the ordinary for that HWIC module compared to the router that works correctly? It could be a bad port if this is something new. There really isn't all that much configuration to be done on an HWIC-4ESW and clean config should at least show the CDP neighbor if the interface is up and the phone boots. Earl Hough CCIE #16508 (RS/Security/Voice) -Original Message- From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Webb Posey Sent: Wednesday, July 06, 2011 1:29 PM To: ccie_voice Subject: Re: [OSL | CCIE_Voice] SHOW CDP Neighbor Error On 2811 Router HWIC-4ESW POE I verified the Cable and the other ports and all is well. If I move the cable from port 1 to port 0 the phone boots up normally. Not really sure what else do do but use another port at this point as everything is configured the same. Here is my entire config, I have the exact config on another router and I even went through line by line to ensure that they are the same and the other router works like a champ. version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname RTR2 ! boot-start-marker boot-end-marker ! card type t1 0 0 logging message-counter syslog ! no aaa new-model network-clock-participate wic 0 ! ! ! dot11 syslog ip source-route ! ! ip cef ! ! no ip domain lookup no ipv6 cef ! multilink bundle-name authenticated ! ! ! ! isdn switch-type primary-ni ! ! ! voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip no supplementary-service h225-notify cid-update fax protocol cisco ! ! ! voice class codec 1 codec preference 1 g711ulaw codec preference 2 g729r8 ! ! ! ! voice class h323 1 h225 timeout tcp establish 3 ! ! ! ! ! ! ! ! ! ! ! voice translation-rule 1 rule 1 /^415888\(1...$\)/ /\1/ ! voice translation-rule 7 rule 1 /^1...$/ /888\0/ type any subscriber rule 2 /^5...$/ /408777\0/ type any national ! voice translation-rule 70 rule 1 // // type any subscriber ! voice translation-rule 111 rule 1 /^1...$/ /415888\0/ type any international ! voice translation-rule 112 rule 1 // // type any international ! voice translation-rule 911 rule 1 /^1...$/ /415888\0/ type any subscriber ! voice translation-rule 912 rule 1 // // type any subscriber ! ! voice translation-profile 4DigitDNIS translate called 1 ! voice translation-profile 911 translate calling 911 translate called 912 ! voice translation-profile InternationalDANI translate calling 111 translate called 112 ! voice translation-profile LocalDANI translate calling 7 translate called 70 ! ! voice-card 0 ! ! ! username administrator privilege 15 password 0 ccievoice ! ! ! archive log config hidekeys ! ! controller T1 0/0/0 cablelength long 0db pri-group timeslots 1-24 ! controller T1 0/0/1 cablelength long 0db channel-group 0 timeslots 1-24 ! ! ! ! ! interface Loopback0 ip address 10.10.110.2 255.255.255.255 ip ospf network point-to-point ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/1 description BACKUP CONNECTON ip address 20.1.1.1 255.255.255.252 shutdown duplex auto
[OSL | CCIE_Voice] PSTN-WAN call drop scenario
hi experts, in ipexpert lab, i make call from HQ phone to PSTN-WAN via CUBE, when the call is answered by PSTN-WAN phone, call fails. This is due to codec mismatch and i can get 'TSC rejected' message in 'debug h245 asn1'. I have been succeful in simulating this on everytime in last 5 attempts on ipexpert lab. few days back, i used other providers lab for which i paid lot of money. i did same configuration as i do on ipexpert lab (that is create g729 region which talks to HQ and BR1 region as g729. Assign g729 region to GK device pool. Assign this device pool to GK trunk). (note: I use this trunk to make a 4 digit call to BR2 phone and when i do 'show gatekeeper call', i see 16k used. So, i know that GK trunk is definately using g729 codec.) for PSTN-WAN, i configured CUBE as well. When i make a call to PSTN-WAN when the call is answered call does not drop. I was expecting it to drop due to codec mismatch. Here is my configuration on HQ router: voice service voip all h t h gatkeeper zone local VIA ipexpert.com zone local GK ipexpert.com 10.10.110.1 using local loopback zone remote PSTN-WAN joblog.com outvia VIA zone prefix PSTN-WAN 01191* zone prefix GK 212* gw-priority 10 gk-trunk_2 zone prefix GK 212* gw-priority 9 gk-trunk_1 zone prefix GK 617* gw-priority 10 gk-trunk_2 zone prefix GK 617* gw-priority 9 gk-trunk_1 zone prefix GK 212* gw-priority 0 CME zone prefix GK 617* gw-priority 0 CME no shut int lo 0 ip add 10.10.110.1 255.255.255.0 h323-g v b s 10.10.110.1 h323-g v inter h323-g v id VIA ipadd 10.10.110.1 h323-g v h323-id HQ-RTR gateway dial-p voice 91 voip destination-p 01191T incoming called 01191 session target ras dtmf-r h245-al no vad On CUCM: a route pattern 9.011916737485173 partition: pt-hq-CallToIndia discard digit predot routelist: rl-gk-CallToIndia contains gk trunk calling party External number mask: On Do you guys see any problem in above config. Have you come across similar situation in non-IPexpert lab for which you have paid lot of money? If so, how did you resolve it. Thanks -adil -- .. . . _7___|___|_|_|adil.sha...@gmail.com . . ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Lost lab equipment with new job, looking for softphone options
I lost my phones and router I used to connect to proctorlabs because I started a new job. I know I can use a CIPC and multiple IP Blue phones (with hack), but I had another idea I wondered if anybody has tried. Has anybody used multiple VMs with CIPC on them to connect with proctorlabs? The only thing I am unsure about, is if all VMs can go through the vpn setup through vpn client. Is this possible without a cisco router? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Lost lab equipment with new job, looking for softphone options
Hi Adam, I havent tried that on proctorlabs. But i have done something for some other testing. i had to simulate 15 phones. so i used 3 vm's of windows xp and the IP blue multi lab version. it worked for me. just put the vm in to NAT mode. On Thu, Jul 7, 2011 at 6:21 AM, adam compton com...@gmail.com wrote: I lost my phones and router I used to connect to proctorlabs because I started a new job. I know I can use a CIPC and multiple IP Blue phones (with hack), but I had another idea I wondered if anybody has tried. Has anybody used multiple VMs with CIPC on them to connect with proctorlabs? The only thing I am unsure about, is if all VMs can go through the vpn setup through vpn client. Is this possible without a cisco router? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com -- Ravindra Lakpriya ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
