Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa)
Hi All, I have connected both E1 back to back with PRI crossover but I am getting following error on both side. Please let me know is this normal or it will create problem. HQ-Router#sh controllers e1 E1 0/3/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20090113, FPGA: 20, spm_count = 0 Framing is CRC4, Line Code is HDB3, Clock Source is Internal. Data in current interval (202 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 3 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 3 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Total Data (last 2 15 minute intervals): 3 Line Code Violations, 5 Path Code Violations, 30 Slip Secs, 0 Fr Loss Secs, 3 Line Err Secs, 0 Degraded Mins, 32 Errored Secs, 1 Bursty Err Secs, 0 Severely Err Secs, 0 Unavai HQ-Router# PSTN-FRS#sh controllers e1 E1 0/2/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20090113, FPGA: 20, spm_count = 0 Framing is CRC4, Line Code is HDB3, Clock Source is Internal. Data in current interval (315 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 4 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 4 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Total Data (last 2 15 minute intervals): 3 Line Code Violations, 3 Path Code Violations, 31 Slip Secs, 0 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins, 33 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 2 Unavail Secs I am also not able to register this E1 with MGCP, please help me Thanks Nomi From: michael.se...@compucom.com michael.se...@compucom.com To: ccie_voice@onlinestudylist.com Sent: Saturday, 31 December 2011 5:40 AM Subject: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) I read in the thread below I am using simple crossover cable (Ethernet crossover). This cable will not work. You need a T1 cross over cable: http://www.google.com/search?q=t1+crossover+cablehl=enprmd=imvnstbm=ischtbo=usource=univsa=Xei=3gP-Tp2AIpS5twf-ufXPBgsqi=2ved=0CF4QsAQbiw=1072bih=804 !!! If your using an Ethernet cross over it won't work need T1 cross over 1--4, 2--5, 4--1, 5--2 http://www.ebay.com/itm/T1-Crossover-cable-3FT-/160570999135?pt=LH_DefaultDomain_0hash=item2562c7015f Usually you can pick one up at local computer store or ebay real cheap depending on the length. Hope this helps. Michael Sears ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa)
Did you use the command: isdn protocol-emulate network on your Serial interfaces for T1/E1 on the PSTN side? Can you send your config? *Emanuel Damasceno* CCNP Voice On Tue, Feb 14, 2012 at 11:22 AM, muhammad nouman nouman_n...@yahoo.comwrote: Hi All, I have connected both E1 back to back with PRI crossover but I am getting following error on both side. Please let me know is this normal or it will create problem. HQ-Router#sh controllers e1 E1 0/3/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20090113, FPGA: 20, spm_count = 0 Framing is CRC4, Line Code is HDB3, Clock Source is Internal. Data in current interval (202 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 3 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 3 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Total Data (last 2 15 minute intervals): 3 Line Code Violations, 5 Path Code Violations, 30 Slip Secs, 0 Fr Loss Secs, 3 Line Err Secs, 0 Degraded Mins, 32 Errored Secs, 1 Bursty Err Secs, 0 Severely Err Secs, 0 Unavai HQ-Router# PSTN-FRS#sh controllers e1 E1 0/2/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20090113, FPGA: 20, spm_count = 0 Framing is CRC4, Line Code is HDB3, Clock Source is Internal. Data in current interval (315 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 4 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 4 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Total Data (last 2 15 minute intervals): 3 Line Code Violations, 3 Path Code Violations, 31 Slip Secs, 0 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins, 33 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 2 Unavail Secs I am also not able to register this E1 with MGCP, please help me Thanks Nomi *From:* michael.se...@compucom.com michael.se...@compucom.com *To:* ccie_voice@onlinestudylist.com *Sent:* Saturday, 31 December 2011 5:40 AM *Subject:* [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) I read in the thread below I am using simple crossover cable (Ethernet crossover). This cable will not work. You need a T1 cross over cable: http://www.google.com/search?q=t1+crossover+cablehl=enprmd=imvnstbm=ischtbo=usource=univsa=Xei=3gP-Tp2AIpS5twf-ufXPBgsqi=2ved=0CF4QsAQbiw=1072bih=804 !!! If your using an Ethernet cross over it won't work need T1 cross over 1--4, 2--5, 4--1, 5--2 http://www.ebay.com/itm/T1-Crossover-cable-3FT-/160570999135?pt=LH_DefaultDomain_0hash=item2562c7015f Usually you can pick one up at local computer store or ebay real cheap depending on the length. Hope this helps. Michael Sears ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa)
Yes, I have used isdn protocol-emulate network command, please find here both side config PSTN-FRS# network-clock-participate wic 2 isdn switch-type primary-net5 controller E1 0/2/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/2/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable HQ-Router# network-clock-participate wic 3 isdn switch-type primary-net5 controller E1 0/3/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/3/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable Thanks Nomi From: Emanuel Damasceno aedamasc...@gmail.com To: muhammad nouman nouman_n...@yahoo.com Cc: michael.se...@compucom.com michael.se...@compucom.com; ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com Sent: Wednesday, 15 February 2012 12:47 AM Subject: Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) Did you use the command: isdn protocol-emulate network on your Serial interfaces for T1/E1 on the PSTN side? Can you send your config? Emanuel Damasceno CCNP Voice On Tue, Feb 14, 2012 at 11:22 AM, muhammad nouman nouman_n...@yahoo.com wrote: Hi All, I have connected both E1 back to back with PRI crossover but I am getting following error on both side. Please let me know is this normal or it will create problem. HQ-Router#sh controllers e1 E1 0/3/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20090113, FPGA: 20, spm_count = 0 Framing is CRC4, Line Code is HDB3, Clock Source is Internal. Data in current interval (202 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 3 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 3 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Total Data (last 2 15 minute intervals): 3 Line Code Violations, 5 Path Code Violations, 30 Slip Secs, 0 Fr Loss Secs, 3 Line Err Secs, 0 Degraded Mins, 32 Errored Secs, 1 Bursty Err Secs, 0 Severely Err Secs, 0 Unavai HQ-Router# PSTN-FRS#sh controllers e1 E1 0/2/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20090113, FPGA: 20, spm_count = 0 Framing is CRC4, Line Code is HDB3, Clock Source is Internal. Data in current interval (315 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 4 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 4 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Total Data (last 2 15 minute intervals): 3 Line Code Violations, 3 Path Code Violations, 31 Slip Secs, 0 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins, 33 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 2 Unavail Secs I am also not able to register this E1 with MGCP, please help me Thanks Nomi From: michael.se...@compucom.com michael.se...@compucom.com To: ccie_voice@onlinestudylist.com Sent: Saturday, 31 December 2011 5:40 AM Subject: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) I read in the thread below I am using simple crossover cable (Ethernet crossover). This cable will not work. You need a T1 cross over cable: http://www.google.com/search?q=t1+crossover+cablehl=enprmd=imvnstbm=ischtbo=usource=univsa=Xei=3gP-Tp2AIpS5twf-ufXPBgsqi=2ved=0CF4QsAQbiw=1072bih=804 !!! If your using an Ethernet cross over it won't work need T1 cross over 1--4, 2--5, 4--1, 5--2 http://www.ebay.com/itm/T1-Crossover-cable-3FT-/160570999135?pt=LH_DefaultDomain_0hash=item2562c7015f Usually you can pick one up at local computer store or ebay real cheap depending on the length. Hope this helps. Michael Sears ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa)
Are you using the correct cables? I made my own cables. You should use pins 1, 2, 4, and 5 (as opposed to Ethernet cable which is 1, 2, 3, 6). It's exactly what our friend Michael Sears explained: 1--4, 2--5, 4--1, 5--2. Here is my config. It is working fine and I am using Ethernet crossover (with using the pins described above) and it is working fine: This is the config of the PSTN side. card type t1 0 0 card type e1 0 3 network-clock-participate wic 0 network-clock-participate wic 3 interface Serial0/0/0:23 no ip address encapsulation hdlc isdn switch-type primary-ni isdn protocol-emulate network isdn incoming-voice voice isdn outgoing display-ie isdn outgoing ie redirecting-number no cdp enable interface Serial0/3/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice isdn outgoing display-ie isdn outgoing ie redirecting-number no cdp enable controller E1 0/3/0 clock source internal pri-group timeslots 1-3,16 description # PSTN BR2 # controller T1 0/0/0 clock source internal cablelength long 0db pri-group timeslots 1-3,24 description # PSTN HQ # Now the Site side: network-clock-participate wic 1 network-clock-select 1 T1 0/1/0 controller T1 0/1/0 cablelength long 0db pri-group timeslots 1-3,24 service mgcp interface Serial0/1/0:23 no ip address encapsulation hdlc isdn switch-type primary-ni isdn incoming-voice voice isdn bind-l3 ccm-manager isdn bchan-number-order ascending isdn outgoing display-ie isdn outgoing ie redirecting-number no cdp enable My Site BR2 is not up yet, btu the config will be pretty much the same as T1, except for switch type e port numbers *Emanuel Damasceno* CCNP Voice On Tue, Feb 14, 2012 at 11:58 AM, muhammad nouman nouman_n...@yahoo.comwrote: Yes, I have used isdn protocol-emulate network command, please find here both side config PSTN-FRS# network-clock-participate wic 2 isdn switch-type primary-net5 controller E1 0/2/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/2/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable HQ-Router# network-clock-participate wic 3 isdn switch-type primary-net5 controller E1 0/3/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/3/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable Thanks Nomi *From:* Emanuel Damasceno aedamasc...@gmail.com *To:* muhammad nouman nouman_n...@yahoo.com *Cc:* michael.se...@compucom.com michael.se...@compucom.com; ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com *Sent:* Wednesday, 15 February 2012 12:47 AM *Subject:* Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) Did you use the command: isdn protocol-emulate network on your Serial interfaces for T1/E1 on the PSTN side? Can you send your config? *Emanuel Damasceno* CCNP Voice On Tue, Feb 14, 2012 at 11:22 AM, muhammad nouman nouman_n...@yahoo.comwrote: Hi All, I have connected both E1 back to back with PRI crossover but I am getting following error on both side. Please let me know is this normal or it will create problem. HQ-Router#sh controllers e1 E1 0/3/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20090113, FPGA: 20, spm_count = 0 Framing is CRC4, Line Code is HDB3, Clock Source is Internal. Data in current interval (202 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 3 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 3 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Total Data (last 2 15 minute intervals): 3 Line Code Violations, 5 Path Code Violations, 30 Slip Secs, 0 Fr Loss Secs, 3 Line Err Secs, 0 Degraded Mins, 32 Errored Secs, 1 Bursty Err Secs, 0 Severely Err Secs, 0 Unavai HQ-Router# PSTN-FRS#sh controllers e1 E1 0/2/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20090113, FPGA: 20, spm_count = 0 Framing is CRC4, Line Code is HDB3, Clock Source is Internal. Data in current interval (315 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 4 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 4 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Total Data (last 2 15 minute intervals): 3 Line Code Violations, 3 Path Code Violations, 31 Slip Secs, 0 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins, 33 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 2 Unavail Secs I am also not able to register this E1 with MGCP, please help me Thanks Nomi
Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa)
It seems clocks are unsynched. Please try clock source line on HQ E1 0/3/0. Peter - Original Message - From: muhammad nouman nouman_n...@yahoo.com Date: Tuesday, February 14, 2012 3:26 pm Subject: Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) To: Emanuel Damasceno aedamasc...@gmail.com Cc: ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com, michael.se...@compucom.com michael.se...@compucom.com Yes, I have used isdn protocol-emulate network command, please find here both side config PSTN-FRS# network-clock-participate wic 2 isdn switch-type primary-net5 controller E1 0/2/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/2/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable HQ-Router# network-clock-participate wic 3 isdn switch-type primary-net5 controller E1 0/3/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/3/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable Thanks Nomi From: Emanuel Damasceno aedamasc...@gmail.com To: muhammad nouman nouman_n...@yahoo.com Cc: michael.se...@compucom.com michael.se...@compucom.com; ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com Sent: Wednesday, 15 February 2012 12:47 AM Subject: Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) Did you use the command: isdn protocol-emulate network on your Serial interfaces for T1/E1 on the PSTN side? Can you send your config? Emanuel Damasceno CCNP Voice On Tue, Feb 14, 2012 at 11:22 AM, muhammad nouman nouman_n...@yahoo.com wrote: Hi All, I have connected both E1 back to back with PRI crossover but I am getting following error on both side. Please let me know is this normal or it will create problem. HQ-Router#sh controllers e1 E1 0/3/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20090113, FPGA: 20, spm_count = 0 Framing is CRC4, Line Code is HDB3, Clock Source is Internal. Data in current interval (202 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 3 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 3 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Total Data (last 2 15 minute intervals): 3 Line Code Violations, 5 Path Code Violations, 30 Slip Secs, 0 Fr Loss Secs, 3 Line Err Secs, 0 Degraded Mins, 32 Errored Secs, 1 Bursty Err Secs, 0 Severely Err Secs, 0 Unavai HQ-Router# PSTN-FRS#sh controllers e1 E1 0/2/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20090113, FPGA: 20, spm_count = 0 Framing is CRC4, Line Code is HDB3, Clock Source is Internal. Data in current interval (315 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 4 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 4 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Total Data (last 2 15 minute intervals): 3 Line Code Violations, 3 Path Code Violations, 31 Slip Secs, 0 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins, 33 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 2 Unavail Secs I am also not able to register this E1 with MGCP, please help me Thanks Nomi From: michael.se...@compucom.com michael.se...@compucom.com To: ccie_voice@onlinestudylist.com Sent: Saturday, 31 December 2011 5:40 AM Subject: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) I read in the thread below I am using simple crossover cable (Ethernet crossover). This cable will not work. You need a T1 cross over cable: !!! If your using an Ethernet cross over it won't work need T1 cross over 1--4, 2--5, 4--1, 5--2 Usually you can pick one up at local computer store or ebay real cheap depending on the length. Hope this helps. Michael Sears ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a
Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa)
Hi, You have used protocol-emulate network on both sides. This should only be on one side. On 14 Feb 2012 14:26, muhammad nouman nouman_n...@yahoo.com wrote: Yes, I have used isdn protocol-emulate network command, please find here both side config PSTN-FRS# network-clock-participate wic 2 isdn switch-type primary-net5 controller E1 0/2/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/2/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable HQ-Router# network-clock-participate wic 3 isdn switch-type primary-net5 controller E1 0/3/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/3/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable Thanks Nomi *From:* Emanuel Damasceno aedamasc...@gmail.com *To:* muhammad nouman nouman_n...@yahoo.com *Cc:* michael.se...@compucom.com michael.se...@compucom.com; ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com *Sent:* Wednesday, 15 February 2012 12:47 AM *Subject:* Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) Did you use the command: isdn protocol-emulate network on your Serial interfaces for T1/E1 on the PSTN side? Can you send your config? *Emanuel Damasceno* CCNP Voice On Tue, Feb 14, 2012 at 11:22 AM, muhammad nouman nouman_n...@yahoo.comwrote: Hi All, I have connected both E1 back to back with PRI crossover but I am getting following error on both side. Please let me know is this normal or it will create problem. HQ-Router#sh controllers e1 E1 0/3/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20090113, FPGA: 20, spm_count = 0 Framing is CRC4, Line Code is HDB3, Clock Source is Internal. Data in current interval (202 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 3 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 3 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Total Data (last 2 15 minute intervals): 3 Line Code Violations, 5 Path Code Violations, 30 Slip Secs, 0 Fr Loss Secs, 3 Line Err Secs, 0 Degraded Mins, 32 Errored Secs, 1 Bursty Err Secs, 0 Severely Err Secs, 0 Unavai HQ-Router# PSTN-FRS#sh controllers e1 E1 0/2/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20090113, FPGA: 20, spm_count = 0 Framing is CRC4, Line Code is HDB3, Clock Source is Internal. Data in current interval (315 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 4 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 4 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Total Data (last 2 15 minute intervals): 3 Line Code Violations, 3 Path Code Violations, 31 Slip Secs, 0 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins, 33 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 2 Unavail Secs I am also not able to register this E1 with MGCP, please help me Thanks Nomi *From:* michael.se...@compucom.com michael.se...@compucom.com *To:* ccie_voice@onlinestudylist.com *Sent:* Saturday, 31 December 2011 5:40 AM *Subject:* [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) I read in the thread below I am using simple crossover cable (Ethernet crossover). This cable will not work. You need a T1 cross over cable: http://www.google.com/search?q=t1+crossover+cablehl=enprmd=imvnstbm=ischtbo=usource=univsa=Xei=3gP-Tp2AIpS5twf-ufXPBgsqi=2ved=0CF4QsAQbiw=1072bih=804 !!! If your using an Ethernet cross over it won't work need T1 cross over 1--4, 2--5, 4--1, 5--2 http://www.ebay.com/itm/T1-Crossover-cable-3FT-/160570999135?pt=LH_DefaultDomain_0hash=item2562c7015f Usually you can pick one up at local computer store or ebay real cheap depending on the length. Hope this helps. Michael Sears ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out
Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa)
sorry guys, here is correct logs HQ-Router(config)#ccm-manager config server 10.10.200.21 HQ-Router(config)#cc HQ-Router(config)#ccm-manager c HQ-Router(config)#ccm-manager config HQ-Router(config)# Loading HQ-Router.CCIELAB.COM.cnf.xml from 10.10.200.21 (via FastEthernet0/0): ! [OK - 4840 bytes] This package type is not the default package type. *Feb 14 15:47:58.503: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(1), changed state to Administrative Shutdown *Feb 14 15:47:58.503: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(2), changed state to Administrative Shutdown *Feb 14 15:47:58.503: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(3), changed state to Administrative Shutdown *Feb 14 15:47:58.511: %ISDN-6-LAYER2DOWN: Layer 2 for Interface Se0/3/0:15, TEI 0 changed to down *Feb 14 15:47:58.579: %CONTROLLER-5-UPDOWN: Controller E1 0/3/0, changed state to administratively down *Feb 14 15:48:01.031: %CONTROLLER-5-UPDOWN: Controller E1 0/3/0, changed state to administratively down echo-cancel coverage 8 ^ % Invalid input detected at '^' marker. %A ds0-group was configured already. Please remove it to configure a pri-group *Feb 14 15:48:03.507: voice_port is not initialized *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:0, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:1, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:2, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:3, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:4, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:5, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:6, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:7, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:15, changed state to down *Feb 14 15:48:04.699: %SYS-6-CLOCKUPDATE: System clock has been updated from 02:48:04 utc Wed Feb 15 2012 to 02:48:04 utc Wed Feb 15 2012, configured from console by console. *Feb 14 15:48:05.151: %OSPF-4-CFG_NBR_P2MP_NEEDS_COST: Can not use configured neighbor: cost or database-filter option is required for point-to-multipoint broadcast network *Feb 14 15:48:11.127: %CONTROLLER-5-UPDOWN: Controller E1 0/3/0, changed state to up *Feb 14 15:48:13.127: %LINK-3-UPDOWN: Interface Serial0/3/0:15, changed state to up HQ-Router(config)# From: Kevin Spicer ke...@kevinspicer.co.uk To: muhammad nouman nouman_n...@yahoo.com Cc: ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com; michael.se...@compucom.com michael.se...@compucom.com; Emanuel Damasceno aedamasc...@gmail.com Sent: Wednesday, 15 February 2012 2:17 AM Subject: Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) Hi, You have used protocol-emulate network on both sides. This should only be on one side. On 14 Feb 2012 14:26, muhammad nouman nouman_n...@yahoo.com wrote: Yes, I have used isdn protocol-emulate network command, please find here both side config PSTN-FRS# network-clock-participate wic 2 isdn switch-type primary-net5 controller E1 0/2/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/2/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable HQ-Router# network-clock-participate wic 3 isdn switch-type primary-net5 controller E1 0/3/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/3/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable Thanks Nomi From: Emanuel Damasceno aedamasc...@gmail.com To: muhammad nouman nouman_n...@yahoo.com Cc: michael.se...@compucom.com michael.se...@compucom.com; ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com Sent: Wednesday, 15 February 2012 12:47 AM Subject: Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) Did you use the command: isdn protocol-emulate network on your Serial interfaces for T1/E1 on the PSTN side? Can you send your config? Emanuel Damasceno CCNP Voice On Tue, Feb 14, 2012 at 11:22 AM, muhammad nouman nouman_n...@yahoo.com wrote: Hi All, I have connected both E1 back to back with PRI crossover but I am getting following error on both side. Please let me know is this normal or it will create problem. HQ-Router#sh controllers e1 E1 0/3/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20090113, FPGA: 20,
Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa)
It looks like MGCP is trying to configure a T1 not an E1 On 14 Feb 2012 15:36, muhammad nouman nouman_n...@yahoo.com wrote: sorry guys, here is correct logs HQ-Router(config)#ccm-manager config server 10.10.200.21 HQ-Router(config)#cc HQ-Router(config)#ccm-manager c HQ-Router(config)#ccm-manager config HQ-Router(config)# Loading HQ-Router.CCIELAB.COM.cnf.xml from 10.10.200.21 (via FastEthernet0/0): ! [OK - 4840 bytes] This package type is not the default package type. *Feb 14 15:47:58.503: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(1), changed state to Administrative Shutdown *Feb 14 15:47:58.503: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(2), changed state to Administrative Shutdown *Feb 14 15:47:58.503: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(3), changed state to Administrative Shutdown *Feb 14 15:47:58.511: %ISDN-6-LAYER2DOWN: Layer 2 for Interface Se0/3/0:15, TEI 0 changed to down *Feb 14 15:47:58.579: %CONTROLLER-5-UPDOWN: Controller E1 0/3/0, changed state to administratively down *Feb 14 15:48:01.031: %CONTROLLER-5-UPDOWN: Controller E1 0/3/0, changed state to administratively down echo-cancel coverage 8 ^ % Invalid input detected at '^' marker. %A ds0-group was configured already. Please remove it to configure a pri-group *Feb 14 15:48:03.507: voice_port is not initialized *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:0, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:1, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:2, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:3, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:4, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:5, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:6, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:7, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:15, changed state to down *Feb 14 15:48:04.699: %SYS-6-CLOCKUPDATE: System clock has been updated from 02:48:04 utc Wed Feb 15 2012 to 02:48:04 utc Wed Feb 15 2012, configured from console by console. *Feb 14 15:48:05.151: %OSPF-4-CFG_NBR_P2MP_NEEDS_COST: Can not use configured neighbor: cost or database-filter option is required for point-to-multipoint broadcast network *Feb 14 15:48:11.127: %CONTROLLER-5-UPDOWN: Controller E1 0/3/0, changed state to up *Feb 14 15:48:13.127: %LINK-3-UPDOWN: Interface Serial0/3/0:15, changed state to up HQ-Router(config)# *From:* Kevin Spicer ke...@kevinspicer.co.uk *To:* muhammad nouman nouman_n...@yahoo.com *Cc:* ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com; michael.se...@compucom.com michael.se...@compucom.com; Emanuel Damasceno aedamasc...@gmail.com *Sent:* Wednesday, 15 February 2012 2:17 AM *Subject:* Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) Hi, You have used protocol-emulate network on both sides. This should only be on one side. On 14 Feb 2012 14:26, muhammad nouman nouman_n...@yahoo.com wrote: Yes, I have used isdn protocol-emulate network command, please find here both side config PSTN-FRS# network-clock-participate wic 2 isdn switch-type primary-net5 controller E1 0/2/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/2/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable HQ-Router# network-clock-participate wic 3 isdn switch-type primary-net5 controller E1 0/3/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/3/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable Thanks Nomi *From:* Emanuel Damasceno aedamasc...@gmail.com *To:* muhammad nouman nouman_n...@yahoo.com *Cc:* michael.se...@compucom.com michael.se...@compucom.com; ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com *Sent:* Wednesday, 15 February 2012 12:47 AM *Subject:* Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) Did you use the command: isdn protocol-emulate network on your Serial interfaces for T1/E1 on the PSTN side? Can you send your config? *Emanuel Damasceno* CCNP Voice On Tue, Feb 14, 2012 at 11:22 AM, muhammad nouman nouman_n...@yahoo.comwrote: Hi All, I have connected both E1 back to back with PRI crossover but I am getting following error on both side. Please let me know is this normal or it will create problem. HQ-Router#sh
Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa)
Hi Kevin, Do you have any document or link where I can find what exact parameter I need to set on CUCM to register this E1 with MCGP. Thanks Nomi From: Kevin Spicer ke...@kevinspicer.co.uk To: muhammad nouman nouman_n...@yahoo.com Cc: ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com; Kevin Spicer ke...@kevinspicer.co.uk; Emanuel Damasceno aedamasc...@gmail.com; michael.se...@compucom.com michael.se...@compucom.com Sent: Wednesday, 15 February 2012 2:41 AM Subject: Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) It looks like MGCP is trying to configure a T1 not an E1 On 14 Feb 2012 15:36, muhammad nouman nouman_n...@yahoo.com wrote: sorry guys, here is correct logs HQ-Router(config)#ccm-manager config server 10.10.200.21 HQ-Router(config)#cc HQ-Router(config)#ccm-manager c HQ-Router(config)#ccm-manager config HQ-Router(config)# Loading HQ-Router.CCIELAB.COM.cnf.xml from 10.10.200.21 (via FastEthernet0/0): ! [OK - 4840 bytes] This package type is not the default package type. *Feb 14 15:47:58.503: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(1), changed state to Administrative Shutdown *Feb 14 15:47:58.503: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(2), changed state to Administrative Shutdown *Feb 14 15:47:58.503: %LINK-3-UPDOWN: Interface ISDN-VOICE 0/3/0:15(3), changed state to Administrative Shutdown *Feb 14 15:47:58.511: %ISDN-6-LAYER2DOWN: Layer 2 for Interface Se0/3/0:15, TEI 0 changed to down *Feb 14 15:47:58.579: %CONTROLLER-5-UPDOWN: Controller E1 0/3/0, changed state to administratively down *Feb 14 15:48:01.031: %CONTROLLER-5-UPDOWN: Controller E1 0/3/0, changed state to administratively down echo-cancel coverage 8 ^ % Invalid input detected at '^' marker. %A ds0-group was configured already. Please remove it to configure a pri-group *Feb 14 15:48:03.507: voice_port is not initialized *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:0, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:1, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:2, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:3, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:4, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:5, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:6, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:7, changed state to down *Feb 14 15:48:04.511: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/0:15, changed state to down *Feb 14 15:48:04.699: %SYS-6-CLOCKUPDATE: System clock has been updated from 02:48:04 utc Wed Feb 15 2012 to 02:48:04 utc Wed Feb 15 2012, configured from console by console. *Feb 14 15:48:05.151: %OSPF-4-CFG_NBR_P2MP_NEEDS_COST: Can not use configured neighbor: cost or database-filter option is required for point-to-multipoint broadcast network *Feb 14 15:48:11.127: %CONTROLLER-5-UPDOWN: Controller E1 0/3/0, changed state to up *Feb 14 15:48:13.127: %LINK-3-UPDOWN: Interface Serial0/3/0:15, changed state to up HQ-Router(config)# From: Kevin Spicer ke...@kevinspicer.co.uk To: muhammad nouman nouman_n...@yahoo.com Cc: ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com; michael.se...@compucom.com michael.se...@compucom.com; Emanuel Damasceno aedamasc...@gmail.com Sent: Wednesday, 15 February 2012 2:17 AM Subject: Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) Hi, You have used protocol-emulate network on both sides. This should only be on one side. On 14 Feb 2012 14:26, muhammad nouman nouman_n...@yahoo.com wrote: Yes, I have used isdn protocol-emulate network command, please find here both side config PSTN-FRS# network-clock-participate wic 2 isdn switch-type primary-net5 controller E1 0/2/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/2/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable HQ-Router# network-clock-participate wic 3 isdn switch-type primary-net5 controller E1 0/3/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/3/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable Thanks Nomi From: Emanuel Damasceno aedamasc...@gmail.com To: muhammad nouman nouman_n...@yahoo.com Cc: michael.se...@compucom.com michael.se...@compucom.com; ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com Sent: Wednesday, 15 February 2012 12:47 AM
Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa)
Hi , Try this: network-clock-select 1 E1 0/3/0 Regards, George Abi Rached From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of muhammad nouman Sent: Tuesday, February 14, 2012 4:51 PM To: Emanuel Damasceno Cc: ccie_voice@onlinestudylist.com; michael.se...@compucom.com Subject: Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) Yes, I am using correct cable and I have made changes as advised but still getting error. HQ-Router# controller E1 0/3/0 pri-group timeslots 1-3,16 interface Serial0/3/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn incoming-voice voice no cdp enable ! HQ-Router#sh controllers e1 E1 0/3/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20090113, FPGA: 20, spm_count = 0 Framing is CRC4, Line Code is HDB3, Clock Source is Line. Data in current interval (776 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 19 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 19 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs From: Emanuel Damasceno aedamasc...@gmail.commailto:aedamasc...@gmail.com To: muhammad nouman nouman_n...@yahoo.commailto:nouman_n...@yahoo.com Cc: michael.se...@compucom.commailto:michael.se...@compucom.com michael.se...@compucom.commailto:michael.se...@compucom.com; ccie_voice@onlinestudylist.commailto:ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.commailto:ccie_voice@onlinestudylist.com Sent: Wednesday, 15 February 2012 1:39 AM Subject: Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) Are you using the correct cables? I made my own cables. You should use pins 1, 2, 4, and 5 (as opposed to Ethernet cable which is 1, 2, 3, 6). It's exactly what our friend Michael Sears explained: 1--4, 2--5, 4--1, 5--2. Here is my config. It is working fine and I am using Ethernet crossover (with using the pins described above) and it is working fine: This is the config of the PSTN side. card type t1 0 0 card type e1 0 3 network-clock-participate wic 0 network-clock-participate wic 3 interface Serial0/0/0:23 no ip address encapsulation hdlc isdn switch-type primary-ni isdn protocol-emulate network isdn incoming-voice voice isdn outgoing display-ie isdn outgoing ie redirecting-number no cdp enable interface Serial0/3/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice isdn outgoing display-ie isdn outgoing ie redirecting-number no cdp enable controller E1 0/3/0 clock source internal pri-group timeslots 1-3,16 description # PSTN BR2 # controller T1 0/0/0 clock source internal cablelength long 0db pri-group timeslots 1-3,24 description # PSTN HQ # Now the Site side: network-clock-participate wic 1 network-clock-select 1 T1 0/1/0 controller T1 0/1/0 cablelength long 0db pri-group timeslots 1-3,24 service mgcp interface Serial0/1/0:23 no ip address encapsulation hdlc isdn switch-type primary-ni isdn incoming-voice voice isdn bind-l3 ccm-manager isdn bchan-number-order ascending isdn outgoing display-ie isdn outgoing ie redirecting-number no cdp enable My Site BR2 is not up yet, btu the config will be pretty much the same as T1, except for switch type e port numbers Emanuel Damasceno CCNP Voice On Tue, Feb 14, 2012 at 11:58 AM, muhammad nouman nouman_n...@yahoo.commailto:nouman_n...@yahoo.com wrote: Yes, I have used isdn protocol-emulate network command, please find here both side config PSTN-FRS# network-clock-participate wic 2 isdn switch-type primary-net5 controller E1 0/2/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/2/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable HQ-Router# network-clock-participate wic 3 isdn switch-type primary-net5 controller E1 0/3/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/3/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable Thanks Nomi From: Emanuel Damasceno aedamasc...@gmail.commailto:aedamasc...@gmail.com To: muhammad nouman nouman_n...@yahoo.commailto:nouman_n...@yahoo.com Cc: michael.se...@compucom.commailto:michael.se...@compucom.com michael.se...@compucom.commailto:michael.se...@compucom.com; ccie_voice@onlinestudylist.commailto:ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.commailto:ccie_voice@onlinestudylist.com Sent: Wednesday, 15 February 2012 12:47 AM Subject: Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) Did you use the command: isdn protocol-emulate network on your Serial interfaces for T1/E1 on the PSTN side? Can you send your config? Emanuel Damasceno CCNP Voice On Tue, Feb
[OSL | CCIE_Voice] Passed
Congratulations KP!!! Message: 2 Date: Mon, 13 Feb 2012 12:30:59 -0900 From: CCIEVoiceKP ccievoic...@gmail.com To: ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] Passed Message-ID: CAEkdcKbVG4q0Zs2bU3dR87ve+ 9JvUsJtjn1ycferoRf7R=6...@mail.gmail.com Content-Type: text/plain; charset=iso-8859-1 Just got the results this morning ... passed! CCIE Voice #34696! After 5 attempts, what a huge huge huge relief! Thanks to everyone on the forum for your participation. Even if we never corresponded directly, I've learned a ton from others experiences! Keep up the good work! KP ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa)
Also what show network-clocks sais? U may need to set E1 to be the source instead of backplane. Issue network-clock select command. Peter - Original Message - From: Kevin Spicer ke...@kevinspicer.co.uk Date: Tuesday, February 14, 2012 5:00 pm Subject: Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) To: muhammad nouman nouman_n...@yahoo.com Cc: ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com, michael.se...@compucom.com michael.se...@compucom.com Hi, You have used protocol-emulate network on both sides. This should only be on one side. On 14 Feb 2012 14:26, muhammad nouman nouman_n...@yahoo.com wrote: Yes, I have used isdn protocol-emulate network command, please find here both side config PSTN-FRS# network-clock-participate wic 2 isdn switch-type primary-net5 controller E1 0/2/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/2/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable HQ-Router# network-clock-participate wic 3 isdn switch-type primary-net5 controller E1 0/3/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/3/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable Thanks Nomi *From:* Emanuel Damasceno aedamasc...@gmail.com *To:* muhammad nouman nouman_n...@yahoo.com *Cc:* michael.se...@compucom.com michael.se...@compucom.com; ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com *Sent:* Wednesday, 15 February 2012 12:47 AM *Subject:* Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) Did you use the command: isdn protocol-emulate network on your Serial interfaces for T1/E1 on the PSTN side? Can you send your config? *Emanuel Damasceno* CCNP Voice On Tue, Feb 14, 2012 at 11:22 AM, muhammad nouman nouman_n...@yahoo.comwrote: Hi All, I have connected both E1 back to back with PRI crossover but I am getting following error on both side. Please let me know is this normal or it will create problem. HQ-Router#sh controllers e1 E1 0/3/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20090113, FPGA: 20, spm_count = 0 Framing is CRC4, Line Code is HDB3, Clock Source is Internal. Data in current interval (202 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 3 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 3 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Total Data (last 2 15 minute intervals): 3 Line Code Violations, 5 Path Code Violations, 30 Slip Secs, 0 Fr Loss Secs, 3 Line Err Secs, 0 Degraded Mins, 32 Errored Secs, 1 Bursty Err Secs, 0 Severely Err Secs, 0 Unavai HQ-Router# PSTN-FRS#sh controllers e1 E1 0/2/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20090113, FPGA: 20, spm_count = 0 Framing is CRC4, Line Code is HDB3, Clock Source is Internal. Data in current interval (315 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 4 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 4 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Total Data (last 2 15 minute intervals): 3 Line Code Violations, 3 Path Code Violations, 31 Slip Secs, 0 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins, 33 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 2 Unavail Secs I am also not able to register this E1 with MGCP, please help me Thanks Nomi *From:* michael.se...@compucom.com michael.se...@compucom.com *To:* ccie_voice@onlinestudylist.com *Sent:* Saturday, 31 December 2011 5:40 AM *Subject:* [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) I read in the thread below I am using simple crossover cable (Ethernet crossover). This cable will not work. You need a T1 cross over cable: !!! If your using an Ethernet cross over it won't work need T1 cross over 1--4, 2--5, 4--1, 5--2 Usually you can pick one up at local computer store or ebay real cheap depending on the length. Hope this helps. Michael Sears ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or
Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa)
Hi Guys, Thanks all of you specially Michael, after same modification E1 has registered and UP. Thanks Nomi From: Farkas Péter wormh...@sch.bme.hu To: Kevin Spicer ke...@kevinspicer.co.uk Cc: muhammad nouman nouman_n...@yahoo.com; ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com; michael.se...@compucom.com michael.se...@compucom.com Sent: Wednesday, 15 February 2012 3:19 AM Subject: Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) Also what show network-clocks sais? U may need to set E1 to be the source instead of backplane. Issue network-clock select command. Peter - Original Message - From: Kevin Spicer ke...@kevinspicer.co.uk Date: Tuesday, February 14, 2012 5:00 pm Subject: Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) To: muhammad nouman nouman_n...@yahoo.com Cc: ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com, michael.se...@compucom.com michael.se...@compucom.com Hi, You have used protocol-emulate network on both sides. This should only be on one side. On 14 Feb 2012 14:26, muhammad nouman nouman_n...@yahoo.com wrote: Yes, I have used isdn protocol-emulate network command, please find here both side config PSTN-FRS# network-clock-participate wic 2 isdn switch-type primary-net5 controller E1 0/2/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/2/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable HQ-Router# network-clock-participate wic 3 isdn switch-type primary-net5 controller E1 0/3/0 clock source internal pri-group timeslots 1-3,16 interface Serial0/3/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn protocol-emulate network isdn incoming-voice voice no cdp enable Thanks Nomi *From:* Emanuel Damasceno aedamasc...@gmail.com *To:* muhammad nouman nouman_n...@yahoo.com *Cc:* michael.se...@compucom.com michael.se...@compucom.com; ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com *Sent:* Wednesday, 15 February 2012 12:47 AM *Subject:* Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) Did you use the command: isdn protocol-emulate network on your Serial interfaces for T1/E1 on the PSTN side? Can you send your config? *Emanuel Damasceno* CCNP Voice On Tue, Feb 14, 2012 at 11:22 AM, muhammad nouman nouman_n...@yahoo.comwrote: Hi All, I have connected both E1 back to back with PRI crossover but I am getting following error on both side. Please let me know is this normal or it will create problem. HQ-Router#sh controllers e1 E1 0/3/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20090113, FPGA: 20, spm_count = 0 Framing is CRC4, Line Code is HDB3, Clock Source is Internal. Data in current interval (202 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 3 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 3 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Total Data (last 2 15 minute intervals): 3 Line Code Violations, 5 Path Code Violations, 30 Slip Secs, 0 Fr Loss Secs, 3 Line Err Secs, 0 Degraded Mins, 32 Errored Secs, 1 Bursty Err Secs, 0 Severely Err Secs, 0 Unavai HQ-Router# PSTN-FRS#sh controllers e1 E1 0/2/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Version info Firmware: 20090113, FPGA: 20, spm_count = 0 Framing is CRC4, Line Code is HDB3, Clock Source is Internal. Data in current interval (315 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 4 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 4 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Total Data (last 2 15 minute intervals): 3 Line Code Violations, 3 Path Code Violations, 31 Slip Secs, 0 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins, 33 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 2 Unavail Secs I am also not able to register this E1 with MGCP, please help me Thanks Nomi *From:* michael.se...@compucom.com michael.se...@compucom.com *To:* ccie_voice@onlinestudylist.com *Sent:* Saturday, 31 December 2011 5:40 AM *Subject:* [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) I read in the thread below I am using simple crossover cable (Ethernet crossover). This cable will not work. You need a T1 cross over cable:
[OSL | CCIE_Voice] : E1 configuration (Eliot Ngwa)
please check to make sure that network-clock synchronization is configured. show network-clock thanks, /Baktha Message: 7 Date: Tue, 14 Feb 2012 05:22:33 -0800 (PST) From: muhammad nouman nouman_n...@yahoo.com To: michael.se...@compucom.com michael.se...@compucom.com, ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) Message-ID: 1329225753.3682.yahoomail...@web120705.mail.ne1.yahoo.com Content-Type: text/plain; charset=iso-8859-1 Hi All, ? I have connected both E1 back to back with PRI crossover but I am getting following error on both side. ? Please let me know is this normal or it will create problem. ? HQ-Router#sh controllers e1 E1 0/3/0 is up. ? Applique type is Channelized E1 - balanced ? No alarms detected. ? alarm-trigger is not set ? Version info Firmware: 20090113, FPGA: 20, spm_count = 0 ? Framing is CRC4, Line Code is HDB3, Clock Source is Internal. ? Data in current interval (202 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 3 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 3 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail ? Total Data (last 2 15 minute intervals): 3 Line Code Violations, 5 Path Code Violations, 30 Slip Secs, 0 Fr Loss Secs, 3 Line Err Secs, 0 Degraded Mins, 32 Errored Secs, 1 Bursty Err Secs, 0 Severely Err Secs, 0 Unavai HQ-Router# PSTN-FRS#sh controllers e1 E1 0/2/0 is up. ? Applique type is Channelized E1 - balanced ? No alarms detected. ? alarm-trigger is not set ? Version info Firmware: 20090113, FPGA: 20, spm_count = 0 ? Framing is CRC4, Line Code is HDB3, Clock Source is Internal. ? Data in current interval (315 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 4 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 4 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs ? Total Data (last 2 15 minute intervals): 3 Line Code Violations, 3 Path Code Violations, 31 Slip Secs, 0 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins, 33 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 2 Unavail Secs ? ? I am also not able to register this E1 with MGCP, please help me ? Thanks ? Nomi ? From: michael.se...@compucom.com michael.se...@compucom.com To: ccie_voice@onlinestudylist.com Sent: Saturday, 31 December 2011 5:40 AM Subject: [OSL | CCIE_Voice] E1 configuration (Eliot Ngwa) I read in the thread below I am using simple crossover cable (Ethernet crossover).? This cable will not work.? You need a T1 cross over cable:? http://www.google.com/search?q=t1+crossover+cablehl=enprmd=imvnstbm=ischtbo=usource=univsa=Xei=3gP-Tp2AIpS5twf-ufXPBgsqi=2ved=0CF4QsAQbiw=1072bih=804 !!! If your using an Ethernet cross over it won't work need T1 cross over 1--4, 2--5, 4--1, 5--2 http://www.ebay.com/itm/T1-Crossover-cable-3FT-/160570999135?pt=LH_DefaultDomain_0hash=item2562c7015f Usually you can pick one up at local computer store or ebay real cheap depending on the length. Hope this helps. Michael Sears ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com -- next part -- An HTML attachment was scrubbed... URL: /archives/ccie_voice/attachments/20120214/2608dc35/attachment.html -- ___ CCIE_Voice mailing list CCIE_Voice@onlinestudylist.com http://onlinestudylist.com/mailman/listinfo/ccie_voice End of CCIE_Voice Digest, Vol 72, Issue 80 ** ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Multicast MOH
Hello Experts, I am watching IPExpert's video on demand on Multicast MOH. Did I understand this right? multicast moh 239.1.1.1 port 16384 if I have it like this, I have to put ip pim dense-mode on my interfaces multicast moh 239.1.1.1 port 16384 route 10.10.201.1 10.10.110.2 if I have it like this, I DON'T have to put ip pim dense-mode on my interfaces Could somebody please confirm? Thanks* Emanuel Damasceno* CCNP Voice ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] UCCX: Call redirect to *XXXX DNs
In my experience, I have to do a Call consult Transfer for numbers that start with a * -Chase -- If winners never quit and quitters never win, then who coined the phrase, Quit while you’re still ahead.? Date: Tue, 14 Feb 2012 13:49:56 +0800 From: ascanio.al...@gmail.com To: ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] UCCX: Call redirect to * DNs Hi, I am using the Call Redirect step; if the destination pattern comprises digits, I have no problem redirecting the call. If the destination pattern starts with *, e.g., *5001, I hear, like 3 short beeps, and the redirect fails. Can UCCX dial *XXX numbers? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Multicast MOH
Afaik you never need multicast routing configured for the Moh from flash because this traffic has TTL=1, so it wont traverse Layer 3 boundary. This is why you need the route attribute in the moh statement. Sent from my mobile device, sorry for typos. --- Regards Boris On 15/02/2012, at 8:28, Emanuel Damasceno aedamasc...@gmail.com wrote: Hello Experts, I am watching IPExpert's video on demand on Multicast MOH. Did I understand this right? multicast moh 239.1.1.1 port 16384 if I have it like this, I have to put ip pim dense-mode on my interfaces multicast moh 239.1.1.1 port 16384 route 10.10.201.1 10.10.110.2 if I have it like this, I DON'T have to put ip pim dense-mode on my interfaces Could somebody please confirm? Thanks Emanuel Damasceno CCNP Voice ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Ebook Lab 4: Campus QoS Task 3.1 - 25% bandwidth cap per queue
When you configure campus QoS, by using Auto QoS; an input queue will be created. This will prevent from the phone/trusted device from potentially abusing the EF queue when the traffic crosses the WAN. (Assuming you are not using NBAR to reclassify traffic sent across the WAN) From the QoS SRND: Shaped or Shared bandwidth weights can be assigned to a queue via the srr-queue bandwidth shape and srr-queue bandwidth share interface commands. Shaped mode weights override shared mode weights and use an inverse ratio (1/weight) to determine the shaping bandwidth for the queue. Furthermore, if shaped weights are set to 0, then the queue is operating in shared mode. For example, the following interface command srr-queue bandwidth shape 3 0 0 0 would shape Q1 to 1/3 of the available bandwidth and set all other queues to operate in sharing mode. http://www.cisco.com/en/US/docs/switches/lan/catalyst3750/software/release/12.2_50_se/configuration/guide/swqos.html#wp1202482 If you configure a weight of 0, the corresponding queue operates in shared mode. The weight specified with the srr-queue bandwidth shape command is ignored, and the weights specified with the srr-queue bandwidth share interface configuration command for a queue come into effect. When configuring queues in the same queue-set for both shaping and sharing, make sure that you configure the lowest number queue for shaping. http://www.cisco.com/en/US/docs/switches/lan/catalyst3750/software/release/12.2_50_se/configuration/guide/swqos.html#wp1200681 -Chase -- If winners never quit and quitters never win, then who coined the phrase, Quit while you’re still ahead.? Date: Tue, 14 Feb 2012 08:12:24 +0800 From: ascanio.al...@gmail.com To: ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] Ebook Lab 4: Campus QoS Task 3.1 - 25% bandwidth cap per queue Task 3.1 configure campus qos * egress media in the priority queue * egress signal in the second queue * do not permit any queue to exceed 25% of the total allowable bandwidth Solution: int f1/0/2 auto qos voip cisco-phone !--- adjust auto qos int f1/02 srr-queue bandw shape 4 4 4 4 priority-queue out service-policy input XXX Don't quite understand the solution here: From Vik's explanation I put an asterisks for the rate limiting requirement of 25% for each queue because priority queue command will allow Q1 to use 100% of the queue up to the service-policy applied there. However, the configuration of “4 4 4 4” means each queue is configured to not exceed 1/4 or 25% of the bandwidth. This para confuses me re queue and bandwidth:the PQ will get 100% of the queue, but I thought that the srr shape won't be able to limit Q1, since PQ trumps eveything else. Furthermore the service-policy is an input policy, what does this have to do with egress queueing? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] CCIE Voice Five-Lab, lab1, Q9.1
If i configure: num-exp 2...$ 9001202552... in CCIE Voice Five-Lab, lab1, Q9.1 instead of a separate dial-peer pots (with prefix 9001202552) to call from SC to SA in SRST I have to wait timeout interdigit which isn't the case for a separate dial-peer. Is is possible to avoid timeout interdigit and dial immediately 2... extensions in SA without changing this parameter under telephony-service? If not, does it matter from the proctor point of view? Kind regards, Tomasz___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Out of Office: Fuera de Oficina
Thank you for your email. I will be out of the office until on Tuesday 14th February, and I will respond when I get back in. If it is an urgent matter, please call (55)55459105 or you can contact to Alejandro Juache. If you need support please send a email to sopo...@censystems.com.mx Regards Fredy Tafolla Gracias por su correo electronico. Estare fuera de la oficina hasta el 14 de Febrero. Le contestare una vez que este de vuelta. Si es algo urgente por favor marque al 55(55459105) o pongase en contacto con Alejandro Juache. Si necesita soporte por favor envie un email a sopo...@censystems.com.mx. Saludos Fredy Tafolla ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] built-in bridge support for iLBC g729
can anyone confirm the phone built-in bridge does support g729? I'm running it in my lab, no HW CFB are configured and I put all SW CFB in their own MRG, to be sure they are not used: admin:show perf query class Cisco SW Conference Bridge Device ==query class : - Perf class (Cisco SW Conference Bridge Device) has instances and values: CFB_2 - AllocatedResourceCannotOpenPort = 0 CFB_2 - OutOfResources = 0 CFB_2 - ResourceActive = 0 CFB_2 - ResourceAvailable = 48 CFB_2 - ResourceTotal = 48 CFB_2 - SWConferenceActive = 0 CFB_2 - SWConferenceCompleted = 0 CFB_3 - AllocatedResourceCannotOpenPort = 0 CFB_3 - OutOfResources = 0 CFB_3 - ResourceActive = 0 CFB_3 - ResourceAvailable = 48 CFB_3 - ResourceTotal = 48 CFB_3 - SWConferenceActive = 0 CFB_3 - SWConferenceCompleted = 0 admin:show perf query class Cisco HW Conference Bridge Device ==query class : - Perf class (Cisco HW Conference Bridge Device) has instances and values: no values are returned Nevertheless, the barge function is working: barger and bargee use g722, the 3rd party uses g729. same goes is 3rd party would use iLBC. thanks! ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
