Re: [OSL | CCIE_Voice] CCIE Voice Vol1 Task 5.7
Ok I just tested this again and there must be something wrong with your configuration. I set this up for my HQ phones but depending on your setup you could do it for any phones In cucm create a Route Pattern of 91900, and assign it to the proper partition (maybe none or HQ) Now assign a GW (I used SLRG) Click Block this pattern [Precedence Level Exceeded] Check boxes Provide outside Dial Tone and Urgent Priority As soon as I pick up a phone and dial 91900 it stops and plays the recording. So if this is not working it could be that you do not have it in the right partition so in never gets used or you could have a replication issue. Sent from my iPad On Mar 16, 2013, at 8:51 PM, Tony Zunt tony.z...@gmail.com wrote: Evidently, I didn't read the requirement. Sorry. Would a BLOCK partition on the 900 route pattern along with a called number mask containing a phantom DN do the trick? The DN could be a cti route point forwarded to a Unity call handler which could recite the desired message. On Saturday, March 16, 2013, Tony Zunt wrote: Vignesh Associate the 900 route pattern with a partition called BLOCK. Then add BLOCK to the top of your calling search spaces. I wouldn't think it necessary to do this. Did you select the radio button for 'Do not route this pattern' on the 900 RP? Thanks On Saturday, March 16, 2013, wrote: I have already set that and tried but no luck Bill. Sent from Yahoo! Mail for iPhone Can you try making the block pattern a urgent priority pattern Sent from my iPad On Mar 16, 2013, at 1:05 PM, vignesh sethuraman sethuvign...@yahoo.co.in wrote: Hello Experts, I am working on Task 5.7 from Vol1. Question is to block the 91900? numbers. I have configured a Route pattern to block this number but this Route pattern is overridden by a another Route pattern 9.1[2-9]XX[2-9]XX which I have created for Task 5.6. I understand the longest match wins but I need to make it work as said in the question to play the error message the precedence used is not authorized for your line. Could you please let me know is there a way to make this work as expected in the question or am I missing something. Thanks, Vignesh ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Mobile Voice Access not working since many days!!
Hello All, I have been trying this config for MVA for close to 2 weeks now and it does not work . Here are the details The Issue : == I am trying to Intiate a Call from PSTN phone to site B gateway (H323) 3033300 it should ask for authentication once authenticated press 1 to make any 4 digit calls if it is from SB phone 1 . Make sure to display 4 digits number for calling number along with calling name SB Phone 1 they can use local gateway to make the call. Also 2nd line on PSTN phone should be used to dial 3033300 and you will prompted to login. Details: = My config is following 1) The dial-peers are set in the following way dial-peer voice 102 voip preference 2 destination-pattern 3300 session target ipv4:ip address of the CUCM Pub dtmf-relay h245-alphanumeric codec g711ulaw no vad ! dial-peer voice 5 pots service cmm incoming called-number 3300 no digit-strip 2) here is the MVA service url ! application service cmm http://ip address of the CUCM Pub:8080/ccmivr/pages/IVRMainpage.vxml ! 3) I am stripping 3033300 coming from pstn to last 4 digits using a translation-rule on the voice-port level . That is 3033300 becomes 3300 when it reaches CUCM. 4) On CUCM in the service parameters... Enable Mobile Voice access is set to True Mobile voice access number is 3300 Matching caller id with Remote Destination is Partial Match Number of digits of Caller ID Partial Match is 7 5) The Mobility softkey has been added for on hold and connected at the softkey template level and applied to the phone ( SB PH1) 6)At the User SB phone 1 I have enabled Enable Mobility and Enable Mobile Voice Access also selected the MAC address of the phone 7) Created a Remote Dest profile and selected user id of sb ph1 and the correct calling search space for the phone 8) Added a Remoted Destination number of 9525 9) Also went to device phone and selected the Owner User ID of SB Ph1 10) Cisco Unified Mobile Voice Access Service is running on both Sub and Pub on CUCM Questions : 1) I now dial from the pstn line 9525 on the pstn phone to 3033300 . The prompt I get asks me for a pin . I enter 1 and the call drops . I Even tried entering 12345 ( which the pin for user SB Phone 1) and still the call drops after the prompt. Anything wrong the above config? Anything missing in the config ? Any suggestions? 2) I am strip the number to last 4 digits ( as in step 3) . Is this correct procedure? 3) There is also no QOS setup in the config for now . Anything related to Bandwidth here? Please help! -MJ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] CCIE Voice Vol1 Task 5.7
A few points to clarify, although it seems the question has already been answered... Route selection uses longest match, however the urgent priority flag allows you to route a call as soon as there is a match on that pattern, and the system will not look for a longer match. (In production use sparingly, typically just used for 911.) Partition order - this ONLY matters when you have two identical matches in two or more partitions. If your LD pattern is in a pt higher in the CSS than the block 900, the urgent priority would still force the match to the block pattern. If you had a route LD and a block LD (with the exact same string) then which ever pt is first will be used. In the event you have both a line CSS and device CSS (ie, in the real world) the pt in the line are listed before the device CSS. In this case you typically would put block pt on the line CSS and your local gw pt on the phone CSS. The exception to this is CTI route point, where device CSS is first and line CSS is second. Two good methods to troubleshoot dial plan: 1. Use dialed number analyzer (DNA) Http://pub IP/DNA 2. Dial from a phone using two methods, overlap and en bloc. Overlap is picking up handset (or speaker button) hearing dial tone and dialing one digit at a time. In this method cucm evaluates digit matches one at a time as you dial. En bloc means all at once and is when you dial the full string of digits while on hook, the you either go off hook or press the dial soft key. With this method cucm is forced to evaluate the entire digit string at once. When troubleshooting a string that should route but doesn't, go off hook and dial slowly, listening for the error tone. The position in the string where you get the error will help you find the issue. On Mar 17, 2013 8:09 AM, Bill whl...@gmail.com wrote: Ok I just tested this again and there must be something wrong with your configuration. I set this up for my HQ phones but depending on your setup you could do it for any phones In cucm create a Route Pattern of 91900, and assign it to the proper partition (maybe none or HQ) Now assign a GW (I used SLRG) Click Block this pattern [Precedence Level Exceeded] Check boxes Provide outside Dial Tone and Urgent Priority As soon as I pick up a phone and dial 91900 it stops and plays the recording. So if this is not working it could be that you do not have it in the right partition so in never gets used or you could have a replication issue. Sent from my iPad On Mar 16, 2013, at 8:51 PM, Tony Zunt tony.z...@gmail.com wrote: Evidently, I didn't read the requirement. Sorry. Would a BLOCK partition on the 900 route pattern along with a called number mask containing a phantom DN do the trick? The DN could be a cti route point forwarded to a Unity call handler which could recite the desired message. On Saturday, March 16, 2013, Tony Zunt wrote: Vignesh Associate the 900 route pattern with a partition called BLOCK. Then add BLOCK to the top of your calling search spaces. I wouldn't think it necessary to do this. Did you select the radio button for 'Do not route this pattern' on the 900 RP? Thanks On Saturday, March 16, 2013, wrote: I have already set that and tried but no luck Bill. Sent from Yahoo! Mail for iPhone Can you try making the block pattern a urgent priority pattern Sent from my iPad On Mar 16, 2013, at 1:05 PM, vignesh sethuraman sethuvign...@yahoo.co.in wrote: Hello Experts, I am working on Task 5.7 from Vol1. Question is to block the 91900?numbers. I have configured a Route pattern to block this number but this Route pattern is overridden by a another Route pattern 9.1[2-9]XX[2-9]XX which I have created for Task 5.6. I understand the longest match wins but I need to make it work as said in the question to play the error message the precedence used is not authorized for your line. Could you please let me know is there a way to make this work as expected in the question or am I missing something. Thanks, Vignesh ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Mobile Voice Access not working since many days!!
Sounds like you didn't set the MVA details under Media Resources. I usually get these symptoms if I forget to add this. CUCM Administration/Media Resource/Mobile Voice Access - set the MVA number and locale. Let us know how you get on? regards Peter On 3/17/2013 12:53 PM, sanity insanity wrote: Hello All, I have been trying this config for MVA for close to 2 weeks now and it does not work . Here are the details The Issue : == I am trying to Intiate a Call from PSTN phone to site B gateway (H323) 3033300 it should ask for authentication once authenticated press 1 to make any 4 digit calls if it is from SB phone 1 . Make sure to display 4 digits number for calling number along with calling name SB Phone 1 they can use local gateway to make the call. Also 2nd line on PSTN phone should be used to dial 3033300 and you will prompted to login. Details: = My config is following 1) The dial-peers are set in the following way dial-peer voice 102 voip preference 2 destination-pattern 3300 session target ipv4:ip address of the CUCM Pub dtmf-relay h245-alphanumeric codec g711ulaw no vad ! dial-peer voice 5 pots service cmm incoming called-number 3300 no digit-strip 2) here is the MVA service url ! application service cmm http://ip address of the CUCM Pub:8080/ccmivr/pages/IVRMainpage.vxml ! 3) I am stripping 3033300 coming from pstn to last 4 digits using a translation-rule on the voice-port level . That is 3033300 becomes 3300 when it reaches CUCM. 4) On CUCM in the service parameters... Enable Mobile Voice access is set to True Mobile voice access number is 3300 Matching caller id with Remote Destination is Partial Match Number of digits of Caller ID Partial Match is 7 5) The Mobility softkey has been added for on hold and connected at the softkey template level and applied to the phone ( SB PH1) 6)At the User SB phone 1 I have enabled Enable Mobility and Enable Mobile Voice Access also selected the MAC address of the phone 7) Created a Remote Dest profile and selected user id of sb ph1 and the correct calling search space for the phone 8) Added a Remoted Destination number of 9525 9) Also went to device phone and selected the Owner User ID of SB Ph1 10) Cisco Unified Mobile Voice Access Service is running on both Sub and Pub on CUCM Questions : 1) I now dial from the pstn line 9525 on the pstn phone to 3033300 . The prompt I get asks me for a pin . I enter 1 and the call drops . I Even tried entering 12345 ( which the pin for user SB Phone 1) and still the call drops after the prompt. Anything wrong the above config? Anything missing in the config ? Any suggestions? 2) I am strip the number to last 4 digits ( as in step 3) . Is this correct procedure? 3) There is also no QOS setup in the config for now . Anything related to Bandwidth here? Please help! -MJ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] CUCM DHCP issue
I don't think there is a way to change this in CUCM... ...is there? -Chase Mergenthal -- If winners never quit and quitters never win, then who coined the phrase, Quit while you’re still ahead.? Date: Sat, 16 Mar 2013 20:33:32 +0300 From: ccievoic...@gmail.com To: ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] CUCM DHCP issue Hi experts, i am facing a problem with CUCM DHCP ,my phones are taking an ip address as first IP from starting range and so on actually it has to take last ip first and so on eg: CUCM DHCP range :177.1.11.10 -177.1.11.30 MY phones getting an ip as 177.1.11.10 thanks in advance ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Mobile Voice Access not working since many days!!
dial-peer voice 102 voip preference 2 destination-pattern 3300 session target ipv4:ip address of the CUCM Pub dtmf-relay h245-alphanumeric codec g711ulaw no vad Is site to site g711? Or is your CUCM local? application service cmm http://ip address of the CUCM Pub:8080/ccmivr/pages/IVRMainpage.vxml Did you get success when running this? Enable Mobile Voice access is set to True Mobile voice access number is 3300 Matching caller id with Remote Destination is Partial Match Number of digits of Caller ID Partial Match is 7 Partial match is buggy in the lab version of CUCM Did you set your mobile voice access number under media? Does it work if you call from a phone at the site? From a phone at another site? And of course not working from PSTN Sent from my iPad On Mar 17, 2013, at 7:53 AM, sanity insanity networksanitytoinsan...@gmail.com wrote: Hello All, I have been trying this config for MVA for close to 2 weeks now and it does not work . Here are the details The Issue : == I am trying to Intiate a Call from PSTN phone to site B gateway (H323) 3033300 it should ask for authentication once authenticated press 1 to make any 4 digit calls if it is from SB phone 1 . Make sure to display 4 digits number for calling number along with calling name SB Phone 1 they can use local gateway to make the call. Also 2nd line on PSTN phone should be used to dial 3033300 and you will prompted to login. Details: = My config is following 1) The dial-peers are set in the following way dial-peer voice 102 voip preference 2 destination-pattern 3300 session target ipv4:ip address of the CUCM Pub dtmf-relay h245-alphanumeric codec g711ulaw no vad ! dial-peer voice 5 pots service cmm incoming called-number 3300 no digit-strip 2) here is the MVA service url ! application service cmm http://ip address of the CUCM Pub:8080/ccmivr/pages/IVRMainpage.vxml ! 3) I am stripping 3033300 coming from pstn to last 4 digits using a translation-rule on the voice-port level . That is 3033300 becomes 3300 when it reaches CUCM. 4) On CUCM in the service parameters... Enable Mobile Voice access is set to True Mobile voice access number is 3300 Matching caller id with Remote Destination is Partial Match Number of digits of Caller ID Partial Match is 7 5) The Mobility softkey has been added for on hold and connected at the softkey template level and applied to the phone ( SB PH1) 6)At the User SB phone 1 I have enabled Enable Mobility and Enable Mobile Voice Access also selected the MAC address of the phone 7) Created a Remote Dest profile and selected user id of sb ph1 and the correct calling search space for the phone 8) Added a Remoted Destination number of 9525 9) Also went to device phone and selected the Owner User ID of SB Ph1 10) Cisco Unified Mobile Voice Access Service is running on both Sub and Pub on CUCM Questions : 1) I now dial from the pstn line 9525 on the pstn phone to 3033300 . The prompt I get asks me for a pin . I enter 1 and the call drops . I Even tried entering 12345 ( which the pin for user SB Phone 1) and still the call drops after the prompt. Anything wrong the above config? Anything missing in the config ? Any suggestions? 2) I am strip the number to last 4 digits ( as in step 3) . Is this correct procedure? 3) There is also no QOS setup in the config for now . Anything related to Bandwidth here? Please help! -MJ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] [MVA NOT WORKING] Mobile Voice Access not working since many
Greetings, I think you are doing everything right just need a few tweaks. Place a call from the PSTN line 2 to 3033300 and do debug isdn q931 on gateway. What digits do you see for the calling number. 7 or 10? If seeing 7 digits inbound change your Remote Destination Number to 525, without the 9. If you are seeing 10 digits inbound the NPA, NXX, TNTN change your remote destination number to XXX525, in other words match what you're seeing in the isdn debug for calling party and make that you're Remote Destination Number. Do NOT require the prefix of 9 on the Remote Destination Number. Also, under Remote Destination Information make sure you are putting a tick in Mobile Phone checkbox and a tick in the Enable Mobile Connect checkbox. Otherwise your configuration looks good. Hope you find this helpful. Michael Sears CCIE 38404 Date: Sun, 17 Mar 2013 18:23:01 +0530 From: sanity insanity networksanitytoinsan...@gmail.com To: ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] Mobile Voice Access not working since many days!! Message-ID: cag4zmyxmd5xj67pwv+_gpabedjoydyg+zbnmugtsfuj3nsx...@mail.gmail.com Content-Type: text/plain; charset=iso-8859-1 Hello All, I have been trying this config for MVA for close to 2 weeks now and it does not work . Here are the details The Issue : == I am trying to Intiate a Call from PSTN phone to site B gateway (H323) 3033300 it should ask for authentication once authenticated press 1 to make any 4 digit calls if it is from SB phone 1 . Make sure to display 4 digits number for calling number along with calling name SB Phone 1 they can use local gateway to make the call. Also 2nd line on PSTN phone should be used to dial 3033300 and you will prompted to login. Details: = My config is following 1) The dial-peers are set in the following way dial-peer voice 102 voip preference 2 destination-pattern 3300 session target ipv4:ip address of the CUCM Pub dtmf-relay h245-alphanumeric codec g711ulaw no vad ! dial-peer voice 5 pots service cmm incoming called-number 3300 no digit-strip 2) here is the MVA service url ! application service cmm http://ip address of the CUCM Pub:8080/ccmivr/pages/IVRMainpage.vxml ! 3) I am stripping 3033300 coming from pstn to last 4 digits using a translation-rule on the voice-port level . That is 3033300 becomes 3300 when it reaches CUCM. 4) On CUCM in the service parameters... Enable Mobile Voice access is set to True Mobile voice access number is 3300 Matching caller id with Remote Destination is Partial Match Number of digits of Caller ID Partial Match is 7 5) The Mobility softkey has been added for on hold and connected at the softkey template level and applied to the phone ( SB PH1) 6)At the User SB phone 1 I have enabled Enable Mobility and Enable Mobile Voice Access also selected the MAC address of the phone 7) Created a Remote Dest profile and selected user id of sb ph1 and the correct calling search space for the phone 8) Added a Remoted Destination number of 9525 9) Also went to device phone and selected the Owner User ID of SB Ph1 10) Cisco Unified Mobile Voice Access Service is running on both Sub and Pub on CUCM Questions : 1) I now dial from the pstn line 9525 on the pstn phone to 3033300 . The prompt I get asks me for a pin . I enter 1 and the call drops . I Even tried entering 12345 ( which the pin for user SB Phone 1) and still the call drops after the prompt. Anything wrong the above config? Anything missing in the config ? Any suggestions? 2) I am strip the number to last 4 digits ( as in step 3) . Is this correct procedure? 3) There is also no QOS setup in the config for now . Anything related to Bandwidth here? Please help! -MJ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com