Re: [OSL | CCIE_Voice] MGCP troubleshooting
Hi, This was a stupid mistake while practicing IPX vol.2 lab #5.. on the pre-config it says all mgcp config is ready built-in and I was sleepy that night doing that lab, I didnt really fully checked it, the other day I was repeating the same lab, fresh and I caught a really basic mistake: My mgcp config was really everything there, it was registering but on the IPX proctorlabs INITIAL configs, the isdn bind-l3 command in just ONE site it was missing, yes, basic and stupid, you can easily see that doing a show isdn status, I dont know what the hell happened to me that night.. but making basic mistakes is good, it forced me to spend sometime learning over the basic overall config/structure for mgcp, I went beyond that, played with debugs, removed a few commands, tried to see each behavior for each type of config when something is missing.. even more familiar with the debugs now.. thanks, 2012/2/10 Rick Long rick.l...@ensi.com I've seen this behavior on a H323 gateway when a dial-peer was not set to forward the calls to Call Manager. Can you run a debug voice ccapi inout to see if your call is matching a dialpeer on your gateway instead of using MGCP to forward the call to Call Manager? If it is being processed by a dial-peer you may just need to issue an no mgcp mgcp command to re-associated the device with Call Manager. HTH Rick Long -Original Message- From: ccie_voice-boun...@onlinestudylist.com [mailto: ccie_voice-boun...@onlinestudylist.com] On Behalf Of ccie_voice-requ...@onlinestudylist.com Sent: Wednesday, February 08, 2012 5:38 PM To: ccie_voice@onlinestudylist.com Subject: CCIE_Voice Digest, Vol 72, Issue 46 Send CCIE_Voice mailing list submissions to ccie_voice@onlinestudylist.com To subscribe or unsubscribe via the World Wide Web, visit http://onlinestudylist.com/mailman/listinfo/ccie_voice or, via email, send a message with subject or body 'help' to ccie_voice-requ...@onlinestudylist.com You can reach the person managing the list at ccie_voice-ow...@onlinestudylist.com When replying, please edit your Subject line so it is more specific than Re: Contents of CCIE_Voice digest... Today's Topics: 1. Re: MGCP troubleshooting (Baktha Muralidharan) 2. MVA problem (datucha123 datucha123) 3. Re: Lab Grading (cciev wannabe) 4. Re: MVA problem (Juan Lopez) 5. Re: MVA problem (Mohammed Al Baqari) -- Message: 1 Date: Wed, 8 Feb 2012 13:28:54 -0500 From: Baktha Muralidharan muralic...@gmail.com To: Jeferson Guardia jefers...@gmail.com, OSL Voice ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] MGCP troubleshooting Message-ID: ca+ne39wqp38wl00k332semgojjs3bvooz2pfstcsh5panys...@mail.gmail.com Content-Type: text/plain; charset=iso-8859-1 Hello, Unless the number is not coming in en bloc. In overlap-receiving mode, digits would come in digit by digit. can you post the output of debug isdn q931? Thanks, /Baktha Message: 4 Date: Wed, 8 Feb 2012 17:03:32 +0400 From: datucha123 datucha123 datucha...@gmail.com To: Jeferson Guardia jefers...@gmail.com Cc: OSL Voice ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] MGCP troubleshooting Message-ID: capz0ugovt8ujraq3+ayjk7s378csa0tiu8pogapyjnb-p3w...@mail.gmail.com Content-Type: text/plain; charset=iso-8859-1 debug mgcp packets Trace in CUCM On Wed, Feb 8, 2012 at 3:35 PM, Jeferson Guardia jefers...@gmail.com wrote: Hi, What are the techniques most used to perform MGCP troubleshooting? Yesterday I was doing a lab and had a router with pstn integration, it was set for a CSS where my phones had visibility and significant digits = 4. But whenever I would call out from the PSTN, I would get a second dial tone, I would see the call kicking in thru debug isdn q931 but my phone would simply not ring. Any ideas how to verify that possible behavior ? Articles? tech guides? Thanks, -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://www.platinumplacement.com/ -- next part -- An HTML attachment was scrubbed... URL: /archives/ccie_voice/attachments/20120208/f4478761/attachment.html -- ___ CCIE_Voice mailing list CCIE_Voice@onlinestudylist.com http://onlinestudylist.com/mailman/listinfo/ccie_voice End of CCIE_Voice Digest, Vol 72, Issue 44 ** -- next part -- An HTML attachment was scrubbed... URL: /archives/ccie_voice/attachments
[OSL | CCIE_Voice] OT - UCM 7x bugs?
Hi, Often when doing labs over ucm 7, sometimes I notice specially when messing around with CSS/partitions, if you open multiple windows and for example: You have 5 firefox tabs open CSS-site-A css-B css-C css-D css-E And then you go window by window applying it and saving it, all at once.. I usually find partitions missing later on that CSS previously assigned. I care to check for dbreplication and issues like that, all running fine. is this a bug or something? it's terrible to have to go back at something you sure you've done correctly it just to fix a bug! -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] MGCP troubleshooting
Hi, What are the techniques most used to perform MGCP troubleshooting? Yesterday I was doing a lab and had a router with pstn integration, it was set for a CSS where my phones had visibility and significant digits = 4. But whenever I would call out from the PSTN, I would get a second dial tone, I would see the call kicking in thru debug isdn q931 but my phone would simply not ring. Any ideas how to verify that possible behavior ? Articles? tech guides? Thanks, -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] IPX vol1 Lab9a
Thanks. I am in average doing 2 sessions per day in a row, trying to reproduce mini scenarios and get used and fast with technology, the IPX labs are helping so much! On the vol.2 level I am finding it amazing. Regards, 2012/1/29 Gurpreet Singh Kukreja tycoononway1...@gmail.com Hi Jeferson, If you're preparing for your CCIE VOICE Lab attempt, then i think practice it enough so that you remember them by heart. :). It saves a lot of time in lab if you remember them and time is all that matters there.. Since its an open book exam, try and get familiar with the SRND for CM as you can easily find URLs' in there as mentioned by some one earlier in this post. The SRND for CUCM is available for use on the Desktop in the Lab exam with other SRNDs as well. HTH Gurpreet On Tue, Jan 24, 2012 at 9:09 PM, Jeferson Guardia jefers...@gmail.comwrote: IPMA complex, too many steps.. but somehow I feel after practicing for a while I will get used to it. IPX covers well but for some steps, even watching the video, it doesnt take you where you need a piece of specific information to accomplish a task, example: Adding IP Phone Services for IPMA and EM (Extension Mobility) , I know how to create but the URL string I should create, it doesnt mention where to find it or the full string for it. After googling it, I found the URL. Anyone would have a better way to find these URL`s in case in the future I have to deal with adding new IP Phone Services? This was new to me. Thank you all!! -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Phone reg issues - CUCM
Hi, I often hear a lot common problems of candidates not being able to register phones to CUCM due to a lot of things. I would like to reproduce these problems and be able to fix them all. Anyone would point out a good reference book/article for understanding these common issues? Like dbreplication, NTP sync etc. Thanks, -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Fwd: general doubt 2 sessions straight
Does anyone know anything about this? thx -- Forwarded message -- From: Jeferson Guardia jefers...@gmail.com Date: 2012/1/28 Subject: general doubt 2 sessions straight To: support supp...@ipexpert.com Hi, is the first time I booked 2 sessions straight, is it possible I will continue on the same rack or there is a chance I will be kicked out and given a new pod, have to start my lab all over again from another pod? Let me know, thanks -- Jeferson Guardia CCIE #28157 -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] IPX vol1 Lab9a
IPMA complex, too many steps.. but somehow I feel after practicing for a while I will get used to it. IPX covers well but for some steps, even watching the video, it doesnt take you where you need a piece of specific information to accomplish a task, example: Adding IP Phone Services for IPMA and EM (Extension Mobility) , I know how to create but the URL string I should create, it doesnt mention where to find it or the full string for it. After googling it, I found the URL. Anyone would have a better way to find these URL`s in case in the future I have to deal with adding new IP Phone Services? This was new to me. Thank you all!! -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] IPX vol1 Lab9a
Just found it. Good deal!! :-) Cisco Unified IP Phone Service Configuration Add the Cisco IP Manager Assistant service as a new Cisco Unified IP Phone Service. Configure a name, description, and the URL for the Cisco IP Manager Assistant service. The name and description that you enter should be in the local language because it displays on the manager Cisco Unified IP Phone. For more information, see IP Phone Services Configuration in the *Cisco Unified Communications Manager Administration Guide*. Provide a URL by using the format http://server-ipaddress:8080/ma/servlet/MAService?cmd=doPhoneServiceName=#DEVICENAME# For example http://123.45.67.89:8080/ma/servlet/MAService?cmd=doPhoneServiceName=#DEVICENAME# Configuration Tips To provide redundancy for the Cisco Unified IP Phone Service, create a Cisco Unified IP Phone Service that uses the host name rather than the IP address. The host name in DNS should resolve to both Cisco Unified Communications Manager Assistant primary and backup IP addresses. The phone functionality for softkeys and filtering, as well as the phone service, will fail over automatically in the case of a failover. 2012/1/25 Boris K boris.k...@gmail.com hi mate, you can get IPMA and EM URLs from the CUCM Help page, just search for DEVICENAME UCCX Agent Login and IPPM URLs you need to memorise or remember shortcuts on Cisco site. Regards, Boris On Wed, Jan 25, 2012 at 1:34 PM, Emanuel Damasceno aedamasc...@gmail.comwrote: No brother... The best way is to find and learn where it is on Cisco DocCD... :) *Emanuel Damasceno* CCNP Voice On Wed, Jan 25, 2012 at 12:09 AM, Jeferson Guardia jefers...@gmail.comwrote: IPMA complex, too many steps.. but somehow I feel after practicing for a while I will get used to it. IPX covers well but for some steps, even watching the video, it doesnt take you where you need a piece of specific information to accomplish a task, example: Adding IP Phone Services for IPMA and EM (Extension Mobility) , I know how to create but the URL string I should create, it doesnt mention where to find it or the full string for it. After googling it, I found the URL. Anyone would have a better way to find these URL`s in case in the future I have to deal with adding new IP Phone Services? This was new to me. Thank you all!! -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] IPX vol1 Lab9a
Agreed. Thats why Ive been getting familiar with the SRND. There was a lab today on B-ACD, initially I almost freaked out.. but then after learning Vik`s methodology on getting the flash example from the Config Guide and understanding each command, how the applications fall under each other, it became fairly easy to do. On IPMA + EM, yes.. It will be better to practice both separately until you get confidence and then you can put the whole thing together, just like when you are learning a new technology into pieces and anxious to jump in on mocklabs.. exactly the same, this is not like sometimes you have to run before you can walk.. no you definetly need to walk first.. :-) Thanks everyone Back to my studies! 2012/1/25 Eliot Ngwa eliot.n...@gmail.com In CCIE Voice, there is just too much information out there to be able to remember every single command during the 8-hour lab. Instead of bookmarking a URL during your studies, it will be better to learn how to navigate to your needed section from the Cisco Doc support page: http://www.cisco.com/cisco/web/psa/default.html It is what we will have available during the lab On Tue, Jan 24, 2012 at 9:09 PM, Jeferson Guardia jefers...@gmail.comwrote: IPMA complex, too many steps.. but somehow I feel after practicing for a while I will get used to it. IPX covers well but for some steps, even watching the video, it doesnt take you where you need a piece of specific information to accomplish a task, example: Adding IP Phone Services for IPMA and EM (Extension Mobility) , I know how to create but the URL string I should create, it doesnt mention where to find it or the full string for it. After googling it, I found the URL. Anyone would have a better way to find these URL`s in case in the future I have to deal with adding new IP Phone Services? This was new to me. Thank you all!! -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] IPX voice vol.1 lab #8 - PRI weird behaviour
Getting that weird message with my PRI every 30 seconds, I googled, found people having the same issue but I didnt find any solution and this was at the end of my lab, but anyway it raised my curiosity.. you never know you might get the same thing on the lab, gotta be ready to catch any curve ball they throw at you :-) BR1-RTR# Jan 23 02:21:58.590: ISDN Se0/0/0:23 Q931: RX - RESTART pd = 8 callref = 0x Restart Indicator i = 0x87 Looking at general status looks ok BR1-RTR#sh isdn stat Global ISDN Switchtype = primary-ni %Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not apply ISDN Serial0/0/0:23 interface dsl 0, interface ISDN Switchtype = primary-ni L2 Protocol = Q.921 0x L3 Protocol(s) = CCM MANAGER 0x0003 Layer 1 Status: ACTIVE Layer 2 Status: TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED Layer 3 Status: 0 Active Layer 3 Call(s) Active dsl 0 CCBs = 0 The Free Channel Mask: 0x8007 Number of L2 Discards = 0, L2 Session ID = 11 Total Allocated ISDN CCBs = 0 BR1-RTR# Then my q921 debug tells me the following: BR1-RTR# Jan 23 02:24:28.589: ISDN Se0/0/0:23 Q921: User TX - RRp sapi=0 tei=0 nr=42 Jan 23 02:24:28.589: ISDN Se0/0/0:23 Q921: User RX - INFO sapi=0 tei=0, ns=42 nr=12 Jan 23 02:24:28.589: ISDN Se0/0/0:23 Q921: User TX - RR sapi=0 tei=0 nr=43 Jan 23 02:24:28.593: ISDN Se0/0/0:23 Q921: User RX - RRf sapi=0 tei=0 nr=12 BR1-RTR# Yes, this was at proctorlabs.. I bet some of you might have faced the same issue since this is on the initial config. Somehow I just hate MGCP, yes I tried reconfiguring it and also the famous workaround (no mgcp/mgcp), but it didnt work. Cheers! -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] RSVP CAC Sampling Rate
In other words Nicolas means: do your homework before sending something out. I agree with him, do your own research first and in case you still have issues the holler. On 21/01/2012, at 13:38, Nicolas MICHEL mcl.nico...@gmail.com wrote: Damn man, Do we need to correct you for everything you test ? Dude make your own assumption sometimes and please don't use this list as your please Can you verify this and tell me if I'm wrong or not mailing list. I guess this is a mailing list that is related to CCIE and I'm sure some of your post are very interesting but since we receive maybe 4 or 5 mails from you everyday I feel the need to tell you , man please don't flood us like this !! Have a good day ! ;) Nic Le 21 janv. 2012 à 13:33, datucha123 datucha123 datucha...@gmail.com a écrit : Sorry I make a little mistake here in calculation (at 30ms Sampling Rate G729 needs 40kbps for RSVP CAC), but it does not change the idea of question, So in case of 30ms Sampling Rate, we do not need to add any 16 bkps and: 10 G729 30ms Calls - 40 x 10 = 400kbps On Sat, Jan 21, 2012 at 4:20 PM, datucha123 datucha123 datucha...@gmail.com wrote: Hello, When we are using default sampling rate for codecs, for example G729 of 20ms, then during the RSVP CAC caluclation we need to add 16 bkps for sum of all calls: 10 G729 calls - 24 x 10 + 16 = 256 kbps But when using non-default Sampling Rate for codecs, for instance G729 at 30ms, then we do not have to add 16 but add 12 kbps: 10 G729 30ms calls - 28 x 10 +12 = 292 Is it correct or not? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] RSVP CAC Sampling Rate
This formula is on a Cisco tech note and can be easily googled. I agree with Nicolas. On 21/01/2012, at 16:56, George Goglidze gogli...@gmail.com wrote: Nicolas, I think it would be more constructive if you actually answered the guy. this is a very good question, and I believe a lot of people might have this wrong. As I already answered Datucha in private. I'll just put here the correct formula for calculations as per Cisco SRND: For N amount of calls configured for any codec speed with any sampling period: bandwidth = (N-1) * (configured codec speed on configured sampling period) + (codec speed on worth case scenario sampling period - 10ms) as per this example for g729 configured with 30ms sampling period on CUCM for 10 calls: bandwidth= 9 * 19kbps + 40kbps where 19 is g729 speed on 30ms sampling rate... well it's actually 18.648bps but I rounded it up. and 40 is same codec on worth case scenario 10ms sampling rate. Hope this helps, On Sat, Jan 21, 2012 at 4:38 PM, Nicolas MICHEL mcl.nico...@gmail.com wrote: Damn man, Do we need to correct you for everything you test ? Dude make your own assumption sometimes and please don't use this list as your please Can you verify this and tell me if I'm wrong or not mailing list. I guess this is a mailing list that is related to CCIE and I'm sure some of your post are very interesting but since we receive maybe 4 or 5 mails from you everyday I feel the need to tell you , man please don't flood us like this !! Have a good day ! ;) Nic Le 21 janv. 2012 à 13:33, datucha123 datucha123 datucha...@gmail.com a écrit : Sorry I make a little mistake here in calculation (at 30ms Sampling Rate G729 needs 40kbps for RSVP CAC), but it does not change the idea of question, So in case of 30ms Sampling Rate, we do not need to add any 16 bkps and: 10 G729 30ms Calls - 40 x 10 = 400kbps On Sat, Jan 21, 2012 at 4:20 PM, datucha123 datucha123 datucha...@gmail.com wrote: Hello, When we are using default sampling rate for codecs, for example G729 of 20ms, then during the RSVP CAC caluclation we need to add 16 bkps for sum of all calls: 10 G729 calls - 24 x 10 + 16 = 256 kbps But when using non-default Sampling Rate for codecs, for instance G729 at 30ms, then we do not have to add 16 but add 12 kbps: 10 G729 30ms calls - 28 x 10 +12 = 292 Is it correct or not? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Exporting Phones All details - CSV editor Mac
Hi, Thanks for the people who unicasted me - In case anyone google for this and go thru the same issue I had, the solution was changing the encoding to UTF-8. A great CSV editor I was working with was XTabulator, you open the file when exporting data from CCM and it shows perfectly. The free version inserts a row in the middle of the file saying - Program not registered, but CUCM simply gets an error on that line and process all the others, so it works! Regards, 2012/1/15 Jeferson Guardia jefers...@gmail.com Guys, What CSV editor you use on mac for exporting phones details so you dont waste time every session registering phones , entering DN`s , names etc? I tried simply exporting it to excel, saving it as CSV, but then once I upload it to CCM and try running the job on it, it is always returning errors.. Thanks! -- Jeferson Guardia CCIE #28157 -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Exporting Phones All details - CSV editor Mac
Guys, What CSV editor you use on mac for exporting phones details so you dont waste time every session registering phones , entering DN`s , names etc? I tried simply exporting it to excel, saving it as CSV, but then once I upload it to CCM and try running the job on it, it is always returning errors.. Thanks! -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Gatekeepers
I have fully read the article, some Cisco papers, took all 4 lessons on GWGK by Mark Snow , fantastic stuff. I feel much more confident now with GWGK, its like I can picture the whole process in/out on my head after so much theory, how the GWGK process works, the messages, rejections/confirmations, amazing stuff! I strongly recommend to anyone facing issues with this subject. 2012/1/11 Chris Martin clm.c...@gmail.com Going to agree with Abel here, I have read that book a couple times through and while some information is dated, many things have not changed. Chris On Tue, Jan 10, 2012 at 10:42 PM, Abel ... midga...@gmail.com wrote: Try to get an old cisco press book called Gateways and Gatekeepers. Good source of information. On Tue, Jan 10, 2012 at 5:40 PM, Jeferson Guardia jefers...@gmail.comwrote: Thanks, I just read the article and starting the INE deep dive, really helpful stuff, I recommend for anyone facing the same problem. Regards, 2012/1/10 datucha123 datucha123 datucha...@gmail.com INE Deep Dives, and Advanced Technology Class videos. They are great, Also please refer to INE Blog for Gatekeepers: http://blog.ine.com/2009/01/15/gatekeeper-call-routing-at-a-glance/ On Tue, Jan 10, 2012 at 7:12 PM, Jeferson Guardia jefers...@gmail.comwrote: Hi, I need to brush up my gwgk skills, I am really bad at it. Anyone would recommend books , videos , a particular lab? Thank you, -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://www.platinumplacement.com/ -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Gatekeepers
Hi, I need to brush up my gwgk skills, I am really bad at it. Anyone would recommend books , videos , a particular lab? Thank you, -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Gatekeepers
Thanks, I just read the article and starting the INE deep dive, really helpful stuff, I recommend for anyone facing the same problem. Regards, 2012/1/10 datucha123 datucha123 datucha...@gmail.com INE Deep Dives, and Advanced Technology Class videos. They are great, Also please refer to INE Blog for Gatekeepers: http://blog.ine.com/2009/01/15/gatekeeper-call-routing-at-a-glance/ On Tue, Jan 10, 2012 at 7:12 PM, Jeferson Guardia jefers...@gmail.comwrote: Hi, I need to brush up my gwgk skills, I am really bad at it. Anyone would recommend books , videos , a particular lab? Thank you, -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://www.platinumplacement.com/ -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Mac OS X Lion Browser for CCM7
Hi, What browser you mac users work with to do ccm stuff? Ive noticed safari/chrome failing for a lot of small stuff on ccm7, such as when you are adding mgcp and inside the mgcp you have to go specific on a port slot, this didnt show up, I had to do IE (unbelievable) on vmware to get this working.. -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] 2811 + NME-16ES-1G-P
Hi Everyone, Thanks for all replies, I ended up powering everything.. ugly but works.. Would anyone share with me a running config so I can set up the EZVPN and also have an idea how the phones should be setup like? Thanks!! 2011/12/22 Eliot Ngwa eliot.n...@gmail.com You'll need to replace the power supply in 2811 with one that can do inline power ( * PWR-2811-AC-IP )* On Thu, Dec 22, 2011 at 1:43 PM, Jeferson Guardia jefers...@gmail.comwrote: No, it doesnt.. I thought the module NM-16ES itself would do the job.. Waiting for Stack Master Election... POST: Inline Power Controller Tests : Begin POST: Found inline power controller write failure, inst 0 POST: Inline Power Controller Tests : End, Status Failed POST: Inline Power feature is disabled on this switch 2011/12/22 Bill Lake whl...@gmail.com Does your router have an inline power PSU? On Thu, Dec 22, 2011 at 12:25 PM, Jeferson Guardia jefers...@gmail.comwrote: I have manually tried to send some power to the port but it fails Switch(config-if)#int fa1/0/1 Switch(config-if)#power inl Switch(config-if)#power inlin stat Command rejected: power inline static: pwr not available Fa1/0/1 Switch(config-if)#do sh ip int br Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES unset up up FastEthernet1/0/1 unassigned YES unset down down FastEthernet1/0/2 unassigned YES unset down down FastEthernet1/0/3 unassigned YES unset down down FastEthernet1/0/4 unassigned YES unset down down FastEthernet1/0/5 unassigned YES unset down down FastEthernet1/0/6 unassigned YES unset down down FastEthernet1/0/7 unassigned YES unset down down FastEthernet1/0/8 unassigned YES unset down down FastEthernet1/0/9 unassigned YES unset down down FastEthernet1/0/10 unassigned YES unset down down FastEthernet1/0/11 unassigned YES unset down down FastEthernet1/0/12 unassigned YES unset down down FastEthernet1/0/13 unassigned YES unset down down FastEthernet1/0/14 unassigned YES unset down down FastEthernet1/0/15 unassigned YES unset down down FastEthernet1/0/16 unassigned YES unset down down GigabitEthernet1/0/1 unassigned YES unset down down GigabitEthernet1/0/2 unassigned YES unset up up Switch(config-if)# 2011/12/22 Jeferson Guardia jefers...@gmail.com Hi, Not sure if I am missing anything.. I have applied power inline auto to all ports and no shut it, even though I hook up an IP Phone to any port, the port still shows down/down and doesnt provide power.. ideas? Switch Router#sh inv NAME: 2811 chassis, DESCR: 2811 chassis PID: CISCO2811 , VID: V07 , SN: FTX1409AJXF NAME: VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0, DESCR: VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN: FOC13372PB8 NAME: PVDMII DSP SIMM with one DSP with half channel capcity on Slot 0 SubSlot 4, DESCR: PVDMII DSP SIMM with one DSP with half channel capcity PID: PVDM2-8 , VID: V01 , SN: FOC133606RM NAME: PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 5, DESCR: PVDMII DSP SIMM with one DSP PID: PVDM2-16 , VID: V01 , SN: FOC134114TS NAME: NME-16ES-1G-P: EtherSwitch SM 16 10/100T PoE + 1 GE on Slot 1, DESCR: NME-16ES-1G-P: EtherSwitch SM 16 10/100T PoE + 1 GE PID: NME-16ES-1G-P , VID: V04, SN: FOC15424HZ3 Router# [Resuming connection 1 to 5.5.5.5 ... ] Switchen Switch#sh power inl Module Available Used Remaining (Watts) (Watts)(Watts) -- - - 1 n/an/a n/a Interface Admin Oper Power Device Class Max (Watts) - -- -- --- --- - Fa1/0/1 auto off0.0 n/a n/a 15.4 Fa1/0/2 auto off0.0 n/a n/a 15.4 Fa1/0/3 auto off0.0 n/a n/a 15.4 Fa1/0/4 auto off0.0 n/a n/a 15.4 Fa1/0/5 auto off0.0 n/a n/a 15.4 Fa1/0/6 auto off0.0 n/a n/a 15.4 Fa1/0/7 auto off0.0 n/a n/a 15.4 Fa1/0/8 auto off0.0 n/a n/a 15.4 Fa1/0/9 auto off0.0 n/a n/a 15.4 Fa1/0/10 auto off0.0 n/a n/a 15.4 Fa1/0/11 auto off0.0 n/a n/a 15.4 Fa1/0/12 auto off0.0 n/a n/a 15.4 Fa1/0/13 auto off0.0 n/a n/a 15.4 Fa1/0/14 auto off0.0 n/a n
[OSL | CCIE_Voice] 2811 + NME-16ES-1G-P
Hi, Not sure if I am missing anything.. I have applied power inline auto to all ports and no shut it, even though I hook up an IP Phone to any port, the port still shows down/down and doesnt provide power.. ideas? Switch Router#sh inv NAME: 2811 chassis, DESCR: 2811 chassis PID: CISCO2811 , VID: V07 , SN: FTX1409AJXF NAME: VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0, DESCR: VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN: FOC13372PB8 NAME: PVDMII DSP SIMM with one DSP with half channel capcity on Slot 0 SubSlot 4, DESCR: PVDMII DSP SIMM with one DSP with half channel capcity PID: PVDM2-8 , VID: V01 , SN: FOC133606RM NAME: PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 5, DESCR: PVDMII DSP SIMM with one DSP PID: PVDM2-16 , VID: V01 , SN: FOC134114TS NAME: NME-16ES-1G-P: EtherSwitch SM 16 10/100T PoE + 1 GE on Slot 1, DESCR: NME-16ES-1G-P: EtherSwitch SM 16 10/100T PoE + 1 GE PID: NME-16ES-1G-P , VID: V04, SN: FOC15424HZ3 Router# [Resuming connection 1 to 5.5.5.5 ... ] Switchen Switch#sh power inl Module Available Used Remaining (Watts) (Watts)(Watts) -- - - 1 n/an/a n/a Interface Admin Oper Power Device Class Max (Watts) - -- -- --- --- - Fa1/0/1 auto off0.0 n/a n/a 15.4 Fa1/0/2 auto off0.0 n/a n/a 15.4 Fa1/0/3 auto off0.0 n/a n/a 15.4 Fa1/0/4 auto off0.0 n/a n/a 15.4 Fa1/0/5 auto off0.0 n/a n/a 15.4 Fa1/0/6 auto off0.0 n/a n/a 15.4 Fa1/0/7 auto off0.0 n/a n/a 15.4 Fa1/0/8 auto off0.0 n/a n/a 15.4 Fa1/0/9 auto off0.0 n/a n/a 15.4 Fa1/0/10 auto off0.0 n/a n/a 15.4 Fa1/0/11 auto off0.0 n/a n/a 15.4 Fa1/0/12 auto off0.0 n/a n/a 15.4 Fa1/0/13 auto off0.0 n/a n/a 15.4 Fa1/0/14 auto off0.0 n/a n/a 15.4 Fa1/0/15 auto off0.0 n/a n/a 15.4 Fa1/0/16 auto off0.0 n/a n/a 15.4 Switch#sh env power SW PID Serial# Status Sys Pwr PoE Pwr Watts -- -- -- --- --- --- - 1 Built-in Good Switch# -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] 2811 + NME-16ES-1G-P
I have manually tried to send some power to the port but it fails Switch(config-if)#int fa1/0/1 Switch(config-if)#power inl Switch(config-if)#power inlin stat Command rejected: power inline static: pwr not available Fa1/0/1 Switch(config-if)#do sh ip int br Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES unset upup FastEthernet1/0/1 unassigned YES unset down down FastEthernet1/0/2 unassigned YES unset down down FastEthernet1/0/3 unassigned YES unset down down FastEthernet1/0/4 unassigned YES unset down down FastEthernet1/0/5 unassigned YES unset down down FastEthernet1/0/6 unassigned YES unset down down FastEthernet1/0/7 unassigned YES unset down down FastEthernet1/0/8 unassigned YES unset down down FastEthernet1/0/9 unassigned YES unset down down FastEthernet1/0/10 unassigned YES unset down down FastEthernet1/0/11 unassigned YES unset down down FastEthernet1/0/12 unassigned YES unset down down FastEthernet1/0/13 unassigned YES unset down down FastEthernet1/0/14 unassigned YES unset down down FastEthernet1/0/15 unassigned YES unset down down FastEthernet1/0/16 unassigned YES unset down down GigabitEthernet1/0/1 unassigned YES unset down down GigabitEthernet1/0/2 unassigned YES unset upup Switch(config-if)# 2011/12/22 Jeferson Guardia jefers...@gmail.com Hi, Not sure if I am missing anything.. I have applied power inline auto to all ports and no shut it, even though I hook up an IP Phone to any port, the port still shows down/down and doesnt provide power.. ideas? Switch Router#sh inv NAME: 2811 chassis, DESCR: 2811 chassis PID: CISCO2811 , VID: V07 , SN: FTX1409AJXF NAME: VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0, DESCR: VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN: FOC13372PB8 NAME: PVDMII DSP SIMM with one DSP with half channel capcity on Slot 0 SubSlot 4, DESCR: PVDMII DSP SIMM with one DSP with half channel capcity PID: PVDM2-8 , VID: V01 , SN: FOC133606RM NAME: PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 5, DESCR: PVDMII DSP SIMM with one DSP PID: PVDM2-16 , VID: V01 , SN: FOC134114TS NAME: NME-16ES-1G-P: EtherSwitch SM 16 10/100T PoE + 1 GE on Slot 1, DESCR: NME-16ES-1G-P: EtherSwitch SM 16 10/100T PoE + 1 GE PID: NME-16ES-1G-P , VID: V04, SN: FOC15424HZ3 Router# [Resuming connection 1 to 5.5.5.5 ... ] Switchen Switch#sh power inl Module Available Used Remaining (Watts) (Watts)(Watts) -- - - 1 n/an/a n/a Interface Admin Oper Power Device Class Max (Watts) - -- -- --- --- - Fa1/0/1 auto off0.0 n/a n/a 15.4 Fa1/0/2 auto off0.0 n/a n/a 15.4 Fa1/0/3 auto off0.0 n/a n/a 15.4 Fa1/0/4 auto off0.0 n/a n/a 15.4 Fa1/0/5 auto off0.0 n/a n/a 15.4 Fa1/0/6 auto off0.0 n/a n/a 15.4 Fa1/0/7 auto off0.0 n/a n/a 15.4 Fa1/0/8 auto off0.0 n/a n/a 15.4 Fa1/0/9 auto off0.0 n/a n/a 15.4 Fa1/0/10 auto off0.0 n/a n/a 15.4 Fa1/0/11 auto off0.0 n/a n/a 15.4 Fa1/0/12 auto off0.0 n/a n/a 15.4 Fa1/0/13 auto off0.0 n/a n/a 15.4 Fa1/0/14 auto off0.0 n/a n/a 15.4 Fa1/0/15 auto off0.0 n/a n/a 15.4 Fa1/0/16 auto off0.0 n/a n/a 15.4 Switch#sh env power SW PID Serial# Status Sys Pwr PoE Pwr Watts -- -- -- --- --- --- - 1 Built-in Good Switch# -- Jeferson Guardia CCIE #28157 -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] 2811 + NME-16ES-1G-P
Tracing a log just found that while booting the module : *Mar 1 00:00:33.252: %STACKMGR-4-SWITCH_ADDED: Switch 1 has been ADDED to the stack *Mar 1 00:00:33.319: %ILPOWER-3-CONTROLLER_POST_ERR: Inline Power Feature is disabled on this switch because Power On Self Test (POST) failed on this switch. Please consult TECH support for further assistance 2011/12/22 Jeferson Guardia jefers...@gmail.com I have manually tried to send some power to the port but it fails Switch(config-if)#int fa1/0/1 Switch(config-if)#power inl Switch(config-if)#power inlin stat Command rejected: power inline static: pwr not available Fa1/0/1 Switch(config-if)#do sh ip int br Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES unset upup FastEthernet1/0/1 unassigned YES unset down down FastEthernet1/0/2 unassigned YES unset down down FastEthernet1/0/3 unassigned YES unset down down FastEthernet1/0/4 unassigned YES unset down down FastEthernet1/0/5 unassigned YES unset down down FastEthernet1/0/6 unassigned YES unset down down FastEthernet1/0/7 unassigned YES unset down down FastEthernet1/0/8 unassigned YES unset down down FastEthernet1/0/9 unassigned YES unset down down FastEthernet1/0/10 unassigned YES unset down down FastEthernet1/0/11 unassigned YES unset down down FastEthernet1/0/12 unassigned YES unset down down FastEthernet1/0/13 unassigned YES unset down down FastEthernet1/0/14 unassigned YES unset down down FastEthernet1/0/15 unassigned YES unset down down FastEthernet1/0/16 unassigned YES unset down down GigabitEthernet1/0/1 unassigned YES unset down down GigabitEthernet1/0/2 unassigned YES unset upup Switch(config-if)# 2011/12/22 Jeferson Guardia jefers...@gmail.com Hi, Not sure if I am missing anything.. I have applied power inline auto to all ports and no shut it, even though I hook up an IP Phone to any port, the port still shows down/down and doesnt provide power.. ideas? Switch Router#sh inv NAME: 2811 chassis, DESCR: 2811 chassis PID: CISCO2811 , VID: V07 , SN: FTX1409AJXF NAME: VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0, DESCR: VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN: FOC13372PB8 NAME: PVDMII DSP SIMM with one DSP with half channel capcity on Slot 0 SubSlot 4, DESCR: PVDMII DSP SIMM with one DSP with half channel capcity PID: PVDM2-8 , VID: V01 , SN: FOC133606RM NAME: PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 5, DESCR: PVDMII DSP SIMM with one DSP PID: PVDM2-16 , VID: V01 , SN: FOC134114TS NAME: NME-16ES-1G-P: EtherSwitch SM 16 10/100T PoE + 1 GE on Slot 1, DESCR: NME-16ES-1G-P: EtherSwitch SM 16 10/100T PoE + 1 GE PID: NME-16ES-1G-P , VID: V04, SN: FOC15424HZ3 Router# [Resuming connection 1 to 5.5.5.5 ... ] Switchen Switch#sh power inl Module Available Used Remaining (Watts) (Watts)(Watts) -- - - 1 n/an/a n/a Interface Admin Oper Power Device Class Max (Watts) - -- -- --- --- - Fa1/0/1 auto off0.0 n/a n/a 15.4 Fa1/0/2 auto off0.0 n/a n/a 15.4 Fa1/0/3 auto off0.0 n/a n/a 15.4 Fa1/0/4 auto off0.0 n/a n/a 15.4 Fa1/0/5 auto off0.0 n/a n/a 15.4 Fa1/0/6 auto off0.0 n/a n/a 15.4 Fa1/0/7 auto off0.0 n/a n/a 15.4 Fa1/0/8 auto off0.0 n/a n/a 15.4 Fa1/0/9 auto off0.0 n/a n/a 15.4 Fa1/0/10 auto off0.0 n/a n/a 15.4 Fa1/0/11 auto off0.0 n/a n/a 15.4 Fa1/0/12 auto off0.0 n/a n/a 15.4 Fa1/0/13 auto off0.0 n/a n/a 15.4 Fa1/0/14 auto off0.0 n/a n/a 15.4 Fa1/0/15 auto off0.0 n/a n/a 15.4 Fa1/0/16 auto off0.0 n/a n/a 15.4 Switch#sh env power SW PID Serial# Status Sys Pwr PoE Pwr Watts -- -- -- --- --- --- - 1 Built-in Good Switch# -- Jeferson Guardia CCIE #28157 -- Jeferson Guardia CCIE #28157 -- Jeferson Guardia CCIE #28157
Re: [OSL | CCIE_Voice] 2811 + NME-16ES-1G-P
No, it doesnt.. I thought the module NM-16ES itself would do the job.. Waiting for Stack Master Election... POST: Inline Power Controller Tests : Begin POST: Found inline power controller write failure, inst 0 POST: Inline Power Controller Tests : End, Status Failed POST: Inline Power feature is disabled on this switch 2011/12/22 Bill Lake whl...@gmail.com Does your router have an inline power PSU? On Thu, Dec 22, 2011 at 12:25 PM, Jeferson Guardia jefers...@gmail.comwrote: I have manually tried to send some power to the port but it fails Switch(config-if)#int fa1/0/1 Switch(config-if)#power inl Switch(config-if)#power inlin stat Command rejected: power inline static: pwr not available Fa1/0/1 Switch(config-if)#do sh ip int br Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES unset up up FastEthernet1/0/1 unassigned YES unset down down FastEthernet1/0/2 unassigned YES unset down down FastEthernet1/0/3 unassigned YES unset down down FastEthernet1/0/4 unassigned YES unset down down FastEthernet1/0/5 unassigned YES unset down down FastEthernet1/0/6 unassigned YES unset down down FastEthernet1/0/7 unassigned YES unset down down FastEthernet1/0/8 unassigned YES unset down down FastEthernet1/0/9 unassigned YES unset down down FastEthernet1/0/10 unassigned YES unset down down FastEthernet1/0/11 unassigned YES unset down down FastEthernet1/0/12 unassigned YES unset down down FastEthernet1/0/13 unassigned YES unset down down FastEthernet1/0/14 unassigned YES unset down down FastEthernet1/0/15 unassigned YES unset down down FastEthernet1/0/16 unassigned YES unset down down GigabitEthernet1/0/1 unassigned YES unset down down GigabitEthernet1/0/2 unassigned YES unset up up Switch(config-if)# 2011/12/22 Jeferson Guardia jefers...@gmail.com Hi, Not sure if I am missing anything.. I have applied power inline auto to all ports and no shut it, even though I hook up an IP Phone to any port, the port still shows down/down and doesnt provide power.. ideas? Switch Router#sh inv NAME: 2811 chassis, DESCR: 2811 chassis PID: CISCO2811 , VID: V07 , SN: FTX1409AJXF NAME: VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0, DESCR: VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN: FOC13372PB8 NAME: PVDMII DSP SIMM with one DSP with half channel capcity on Slot 0 SubSlot 4, DESCR: PVDMII DSP SIMM with one DSP with half channel capcity PID: PVDM2-8 , VID: V01 , SN: FOC133606RM NAME: PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 5, DESCR: PVDMII DSP SIMM with one DSP PID: PVDM2-16 , VID: V01 , SN: FOC134114TS NAME: NME-16ES-1G-P: EtherSwitch SM 16 10/100T PoE + 1 GE on Slot 1, DESCR: NME-16ES-1G-P: EtherSwitch SM 16 10/100T PoE + 1 GE PID: NME-16ES-1G-P , VID: V04, SN: FOC15424HZ3 Router# [Resuming connection 1 to 5.5.5.5 ... ] Switchen Switch#sh power inl Module Available Used Remaining (Watts) (Watts)(Watts) -- - - 1 n/an/a n/a Interface Admin Oper Power Device Class Max (Watts) - -- -- --- --- - Fa1/0/1 auto off0.0 n/a n/a 15.4 Fa1/0/2 auto off0.0 n/a n/a 15.4 Fa1/0/3 auto off0.0 n/a n/a 15.4 Fa1/0/4 auto off0.0 n/a n/a 15.4 Fa1/0/5 auto off0.0 n/a n/a 15.4 Fa1/0/6 auto off0.0 n/a n/a 15.4 Fa1/0/7 auto off0.0 n/a n/a 15.4 Fa1/0/8 auto off0.0 n/a n/a 15.4 Fa1/0/9 auto off0.0 n/a n/a 15.4 Fa1/0/10 auto off0.0 n/a n/a 15.4 Fa1/0/11 auto off0.0 n/a n/a 15.4 Fa1/0/12 auto off0.0 n/a n/a 15.4 Fa1/0/13 auto off0.0 n/a n/a 15.4 Fa1/0/14 auto off0.0 n/a n/a 15.4 Fa1/0/15 auto off0.0 n/a n/a 15.4 Fa1/0/16 auto off0.0 n/a n/a 15.4 Switch#sh env power SW PID Serial# Status Sys Pwr PoE Pwr Watts -- -- -- --- --- --- - 1 Built-in Good Switch# -- Jeferson Guardia CCIE #28157 -- Jeferson Guardia CCIE #28157
Re: [OSL | CCIE_Voice] IP Blue (running multiple instances)
No it doesnt. I put the /d at the end of the shortcut, but just one instance loads up... :( 2011/10/14 Ashraf Ayyash ash.ayy...@gmail.com google doesnt have any answer for this ? Ash On Fri, Oct 14, 2011 at 1:10 PM, Jeferson Guardia jefers...@gmail.com wrote: Hi, I am able to register many phones, do the regedit thing etc. but the only thing that doesnt work for me is the /d added into the path at the end of the shortcut command. It appears that VTGO PC Lite doesnt work loading up many instances for IP Blue on Windows 7. Any ideas? -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] IP Blue (running multiple instances)
this has been solved - win 7 doesnt support multiple ip blues instances and it is official written on their website. I downloaded a very light Win XP image (250mb) from my company and had a new vmware machine where I`ll do all kinds of IE voice stuff such as phoneview / ipblue etc.. way to go! so bad win 7 doesnt to support but at the end .. the xp is running much more smooth in vmware fusion. Regards, 2011/10/15 Jeferson Guardia jefers...@gmail.com No it doesnt. I put the /d at the end of the shortcut, but just one instance loads up... :( 2011/10/14 Ashraf Ayyash ash.ayy...@gmail.com google doesnt have any answer for this ? Ash On Fri, Oct 14, 2011 at 1:10 PM, Jeferson Guardia jefers...@gmail.com wrote: Hi, I am able to register many phones, do the regedit thing etc. but the only thing that doesnt work for me is the /d added into the path at the end of the shortcut command. It appears that VTGO PC Lite doesnt work loading up many instances for IP Blue on Windows 7. Any ideas? -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com -- Jeferson Guardia CCIE #28157 -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] IP Blue (running multiple instances)
Hi, I am able to register many phones, do the regedit thing etc. but the only thing that doesnt work for me is the /d added into the path at the end of the shortcut command. It appears that VTGO PC Lite doesnt work loading up many instances for IP Blue on Windows 7. Any ideas? -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] PhoneView - Fusion VMware
Hi, While doing a voice rack session, I loaded PhoneView in my fusion (Mac OS X) and noticed lack of connectivity. Is there any special setup I can bridge the VPN that I am loading on my Mac system onto the vmware system so phoneview works? -- Jeferson Guardia CCIE #28157 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
