Re: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher.
I saw the same error today with regard to db replication from the callmanager db rpl status unified report. Not all servers have a good replication status. See the details.View DetailsServerNumber of Replicates CreatedReplicate_State10.10.210.104124 - setup failed10.10.210.114124 - setup failed However when i read the following activelog cm/trace/dbl/sdi/ReplicationStatus.2011_04_06_21_31_55.out file, i saw this: SERVER ID STATESTATUS QUEUE CONNECTION CHANGED---g_ucmpub_ccm7_0_1_11000_2 2 Active Local 0g_ucmsub_ccm7_0_1_11000_23 Active Connected 0 Apr 6 21:27:57 This is very confusing. I know replication works in this case because i was able to make changes on the phone. My conclusion is that the unified report is not to be trusted. You have to test the replication by making change on the callmanager. If it works, then it is good. That is my 2 cents. Date: Wed, 6 Apr 2011 10:18:45 +0200 Subject: Re: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. From: krieger.jul...@gmail.com To: johnnyso...@hotmail.com CC: m...@mallalue.net; ccie_voice@onlinestudylist.com That's why you must check this out as soon as possible when you are on your POD. If you find that you cannot access your ccmadmin (and that it is not a routing issue), or that you have a db replication issue, you must tell your proctor immediately. If you wait too long in the day, the proctor will probably thing that it is a mistake on your side... if it is early in the day, he will check it out and give you extra time... 2011/4/6 Johnny Soong johnnyso...@hotmail.com i will take your advice next time when it happen. Just hope that this doesn't happen in the real lab. I spend 4 hrs troubleshooting this. Thanks. From: m...@mallalue.net To: johnnyso...@hotmail.com; krieger.jul...@gmail.com CC: ccie_voice@onlinestudylist.com Subject: RE: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. Date: Tue, 5 Apr 2011 20:53:45 + Johnny, Next time, try the following - On SUB : utils dbreplication stop - On PUB : utils dbreplication stop utils dbreplication clusterreset I’ve used the clusterreset successfully when repair and reset don’t work Mark. From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Johnny Soong Sent: 05 April 2011 19:03 To: krieger.jul...@gmail.com Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. i tried to change the extension on the phone. It did change. So i know replication is not working. I had to revert the configuration on the Callmanager to make it work. I don't know if there is a fix. Publisher replication is down. Repair wont work. Reboot didn't help. Reset doesn't do anything in this case. Since the Replic state is different. If both the Sub and Pub Rpl state is other than 2 and they are the same, then repair will work. Reset will work if you have diferrent repl state. I tried that already. Date: Tue, 5 Apr 2011 19:31:14 +0200 Subject: Re: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. From: krieger.jul...@gmail.com To: johnnyso...@hotmail.com CC: ccie_voice@onlinestudylist.com Hi Johnny, Even if the utils dbreplication commands do not show what we are looking for (2), does the replication work? Try to create a new region on the pub and see if it has replicated to the sub. Then try the following command on the sub to see if it worked : run sql select name from region If replication worked, you should see on your sub the newly created region Julien 2011/4/5 Johnny Soong johnnyso...@hotmail.com I ran into an issue with the Publisher. The DB Replication is broken. It is showing 3 in the state status. When i tried to issue the utils dbreplicate status. It said the following:Status cannot be performed when replication is down on the publisher, or on a cluster with a single active node; aborting replication status check operation. I did the utils dbreplic stop on the sub and then on the pub. Then i did the utils dbreplic reset 10.10.210.10 on the Pub. It didn't help. Replic is still showing 3 on the Pub. Sub is showing 2 which is fine. I can't issue utils dbreplic repair because the pub replic is down. I rebooted both servers. It didn't do any good. Any suggestion? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher.
I did tried all the options:Option1: subscriber, utis dbrepl stoppub, utils dbrepl stopthen utils dbrepl clusterreset from Pub Result: database replication stopped on subscriber. Couldn't reset from Pub. Had to restart the Sub. Option 2;subscriber: utils dbrepl stoppub: uitls dbrepl stopthen utils dbrepl reset all from Pub Option 3:subscriber: utils dbrepl stoppub: uitls dbrepl stopthen utils dbrepl repair all from Pub Still no good. Still no good. i checked ntp from the Sub. It is in sync with Pub. If rpl state 2 is required, and i can't get it to show. I rather forgo those points than spend too much time on it. Otherwise, i wont be able to finish the lab. From: m...@mallalue.net To: johnnyso...@hotmail.com; krieger.jul...@gmail.com CC: ccie_voice@onlinestudylist.com Subject: RE: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. Date: Wed, 6 Apr 2011 23:01:06 + I’m not a proctor, but if it’s not 2 and 2, then I think that’s no points for that troubleshooting section. You can still make updates to the publisher (and set you’re devices to register with the publisher as primary) while replication is fixing itself. I did this for at least two hours during the IPExpert boot camp I attended! Fix that replication - changes will get to the subscriber eventually! From: Johnny Soong [mailto:johnnyso...@hotmail.com] Sent: 06 April 2011 22:44 To: krieger.jul...@gmail.com Cc: Mark A. Mallalue; ccie_voice@onlinestudylist.com Subject: RE: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. I saw the same error today with regard to db replication from the callmanager db rpl status unified report. Not all servers have a good replication status. See the details.View DetailsServerNumber of Replicates CreatedReplicate_State10.10.210.104124 - setup failed10.10.210.114124 - setup failedHowever when i read the following activelog cm/trace/dbl/sdi/ReplicationStatus.2011_04_06_21_31_55.out file, i saw this: SERVER ID STATESTATUS QUEUE CONNECTION CHANGED---g_ucmpub_ccm7_0_1_11000_2 2 Active Local 0g_ucmsub_ccm7_0_1_11000_23 Active Connected 0 Apr 6 21:27:57 This is very confusing. I know replication works in this case because i was able to make changes on the phone. My conclusion is that the unified report is not to be trusted. You have to test the replication by making change on the callmanager. If it works, then it is good. That is my 2 cents. Date: Wed, 6 Apr 2011 10:18:45 +0200 Subject: Re: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. From: krieger.jul...@gmail.com To: johnnyso...@hotmail.com CC: m...@mallalue.net; ccie_voice@onlinestudylist.com That's why you must check this out as soon as possible when you are on your POD. If you find that you cannot access your ccmadmin (and that it is not a routing issue), or that you have a db replication issue, you must tell your proctor immediately. If you wait too long in the day, the proctor will probably thing that it is a mistake on your side... if it is early in the day, he will check it out and give you extra time...2011/4/6 Johnny Soong johnnyso...@hotmail.comi will take your advice next time when it happen. Just hope that this doesn't happen in the real lab. I spend 4 hrs troubleshooting this. Thanks. From: m...@mallalue.net To: johnnyso...@hotmail.com; krieger.jul...@gmail.com CC: ccie_voice@onlinestudylist.comSubject: RE: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. Date: Tue, 5 Apr 2011 20:53:45 + Johnny, Next time, try the following- On SUB : utils dbreplication stop- On PUB : utils dbreplication stoputils dbreplication clusterreset I’ve used the clusterreset successfully when repair and reset don’t work Mark. From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Johnny Soong Sent: 05 April 2011 19:03 To: krieger.jul...@gmail.com Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. i tried to change the extension on the phone. It did change. So i know replication is not working. I had to revert the configuration on the Callmanager to make it work. I don't know if there is a fix. Publisher replication is down. Repair wont work. Reboot didn't help. Reset doesn't do anything in this case. Since the Replic state is different. If both the Sub and Pub Rpl state is other than 2 and they are the same, then repair will work. Reset will work if you have diferrent repl state. I tried that already. Date: Tue, 5 Apr 2011 19:31:14 +0200 Subject: Re: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. From: krieger.jul...@gmail.com To: johnnyso...@hotmail.com CC: ccie_voice@onlinestudylist.com
Re: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher.
I think i found the issue. There is a mismatch on the Pub and Sub Callmanager name. The names configured in the callmanager are CM_UCMSUB and CM_UCMPUB. The names in the host file are UCMSUB and UCMPUB. Once i changed the names in the callmanager and reissue the repair all command. I saw the following:Subscriber: admin:show perf query class Number of Replicates Created and State of Replication==query class : - Perf class (Number of Replicates Created and State of Replication) has instances and values:ReplicateCount - Number of Replicates Created = 412ReplicateCount - Replicate_State= 2 Publisher:admin:show perf query class Number of Replicates Created and State of Replication==query class : - Perf class (Number of Replicates Created and State of Replication) has instances and values:ReplicateCount - Number of Replicates Created = 412ReplicateCount - Replicate_State= 2 So the take away is to make sure the hostname match the actual names configured in the callmanager. One way to test it is to do utils network host [hostname configured in the callmanager] not the hostname in the hostname file.If that is pingable, then it is not an issue. From: m...@mallalue.net To: johnnyso...@hotmail.com; krieger.jul...@gmail.com CC: ccie_voice@onlinestudylist.com Subject: RE: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. Date: Wed, 6 Apr 2011 23:01:06 + I’m not a proctor, but if it’s not 2 and 2, then I think that’s no points for that troubleshooting section. You can still make updates to the publisher (and set you’re devices to register with the publisher as primary) while replication is fixing itself. I did this for at least two hours during the IPExpert boot camp I attended! Fix that replication - changes will get to the subscriber eventually! From: Johnny Soong [mailto:johnnyso...@hotmail.com] Sent: 06 April 2011 22:44 To: krieger.jul...@gmail.com Cc: Mark A. Mallalue; ccie_voice@onlinestudylist.com Subject: RE: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. I saw the same error today with regard to db replication from the callmanager db rpl status unified report. Not all servers have a good replication status. See the details.View DetailsServerNumber of Replicates CreatedReplicate_State10.10.210.104124 - setup failed10.10.210.114124 - setup failedHowever when i read the following activelog cm/trace/dbl/sdi/ReplicationStatus.2011_04_06_21_31_55.out file, i saw this: SERVER ID STATESTATUS QUEUE CONNECTION CHANGED---g_ucmpub_ccm7_0_1_11000_2 2 Active Local 0g_ucmsub_ccm7_0_1_11000_23 Active Connected 0 Apr 6 21:27:57 This is very confusing. I know replication works in this case because i was able to make changes on the phone. My conclusion is that the unified report is not to be trusted. You have to test the replication by making change on the callmanager. If it works, then it is good. That is my 2 cents. Date: Wed, 6 Apr 2011 10:18:45 +0200 Subject: Re: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. From: krieger.jul...@gmail.com To: johnnyso...@hotmail.com CC: m...@mallalue.net; ccie_voice@onlinestudylist.com That's why you must check this out as soon as possible when you are on your POD. If you find that you cannot access your ccmadmin (and that it is not a routing issue), or that you have a db replication issue, you must tell your proctor immediately. If you wait too long in the day, the proctor will probably thing that it is a mistake on your side... if it is early in the day, he will check it out and give you extra time...2011/4/6 Johnny Soong johnnyso...@hotmail.comi will take your advice next time when it happen. Just hope that this doesn't happen in the real lab. I spend 4 hrs troubleshooting this. Thanks. From: m...@mallalue.net To: johnnyso...@hotmail.com; krieger.jul...@gmail.com CC: ccie_voice@onlinestudylist.comSubject: RE: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. Date: Tue, 5 Apr 2011 20:53:45 + Johnny, Next time, try the following- On SUB : utils dbreplication stop- On PUB : utils dbreplication stoputils dbreplication clusterreset I’ve used the clusterreset successfully when repair and reset don’t work Mark. From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Johnny Soong Sent: 05 April 2011 19:03 To: krieger.jul...@gmail.com Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. i tried to change the extension on the phone. It did change. So i know replication is not working. I had to revert the configuration on the Callmanager to make it work. I don't know if there is a fix
Re: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher.
When the names are mismatch, unified report will report that replication is not working. This is a known bug with callmanager 6.1.2. CSCsv21137 Bug Details Unified Reporting showing the Sub not reachable Symptom: When running Unified reporting tool in 6.1.2 and specifically the Database summary report it reports one or more of the subs not reachable. You can confirm subs are indeed reachable with 'utils dbreplication status' and seeing all the replicates. 'utils network connectivity' can also confirm connectivity between nodes. Conditions: Subs can ping by hostname and confimred all the tables are good and in sync. Issue occurs with mismatch in case between hostname and database, example: server1 vs. SERVER1. This defect is triggered by CURT using case sensitive search on hostname. Workaround: set database and platform servername to same case. From: m...@mallalue.net To: johnnyso...@hotmail.com; krieger.jul...@gmail.com CC: ccie_voice@onlinestudylist.com Subject: RE: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. Date: Wed, 6 Apr 2011 23:01:06 + I’m not a proctor, but if it’s not 2 and 2, then I think that’s no points for that troubleshooting section. You can still make updates to the publisher (and set you’re devices to register with the publisher as primary) while replication is fixing itself. I did this for at least two hours during the IPExpert boot camp I attended! Fix that replication - changes will get to the subscriber eventually! From: Johnny Soong [mailto:johnnyso...@hotmail.com] Sent: 06 April 2011 22:44 To: krieger.jul...@gmail.com Cc: Mark A. Mallalue; ccie_voice@onlinestudylist.com Subject: RE: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. I saw the same error today with regard to db replication from the callmanager db rpl status unified report. Not all servers have a good replication status. See the details.View DetailsServerNumber of Replicates CreatedReplicate_State10.10.210.104124 - setup failed10.10.210.114124 - setup failedHowever when i read the following activelog cm/trace/dbl/sdi/ReplicationStatus.2011_04_06_21_31_55.out file, i saw this: SERVER ID STATESTATUS QUEUE CONNECTION CHANGED---g_ucmpub_ccm7_0_1_11000_2 2 Active Local 0g_ucmsub_ccm7_0_1_11000_23 Active Connected 0 Apr 6 21:27:57 This is very confusing. I know replication works in this case because i was able to make changes on the phone. My conclusion is that the unified report is not to be trusted. You have to test the replication by making change on the callmanager. If it works, then it is good. That is my 2 cents. Date: Wed, 6 Apr 2011 10:18:45 +0200 Subject: Re: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. From: krieger.jul...@gmail.com To: johnnyso...@hotmail.com CC: m...@mallalue.net; ccie_voice@onlinestudylist.com That's why you must check this out as soon as possible when you are on your POD. If you find that you cannot access your ccmadmin (and that it is not a routing issue), or that you have a db replication issue, you must tell your proctor immediately. If you wait too long in the day, the proctor will probably thing that it is a mistake on your side... if it is early in the day, he will check it out and give you extra time...2011/4/6 Johnny Soong johnnyso...@hotmail.comi will take your advice next time when it happen. Just hope that this doesn't happen in the real lab. I spend 4 hrs troubleshooting this. Thanks. From: m...@mallalue.net To: johnnyso...@hotmail.com; krieger.jul...@gmail.com CC: ccie_voice@onlinestudylist.comSubject: RE: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. Date: Tue, 5 Apr 2011 20:53:45 + Johnny, Next time, try the following- On SUB : utils dbreplication stop- On PUB : utils dbreplication stoputils dbreplication clusterreset I’ve used the clusterreset successfully when repair and reset don’t work Mark. From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Johnny Soong Sent: 05 April 2011 19:03 To: krieger.jul...@gmail.com Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. i tried to change the extension on the phone. It did change. So i know replication is not working. I had to revert the configuration on the Callmanager to make it work. I don't know if there is a fix. Publisher replication is down. Repair wont work. Reboot didn't help. Reset doesn't do anything in this case. Since the Replic state is different. If both the Sub and Pub Rpl state is other than 2 and they are the same, then repair will work. Reset will work if you have diferrent repl state. I tried that already
[OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher.
I ran into an issue with the Publisher. The DB Replication is broken. It is showing 3 in the state status. When i tried to issue the utils dbreplicate status. It said the following:Status cannot be performed when replication is down on the publisher, or on a cluster with a single active node; aborting replication status check operation. I did the utils dbreplic stop on the sub and then on the pub. Then i did the utils dbreplic reset 10.10.210.10 on the Pub. It didn't help. Replic is still showing 3 on the Pub. Sub is showing 2 which is fine. I can't issue utils dbreplic repair because the pub replic is down. I rebooted both servers. It didn't do any good. Any suggestion? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher.
i tried to change the extension on the phone. It did change. So i know replication is not working. I had to revert the configuration on the Callmanager to make it work. I don't know if there is a fix. Publisher replication is down. Repair wont work. Reboot didn't help. Reset doesn't do anything in this case. Since the Replic state is different. If both the Sub and Pub Rpl state is other than 2 and they are the same, then repair will work. Reset will work if you have diferrent repl state. I tried that already. Date: Tue, 5 Apr 2011 19:31:14 +0200 Subject: Re: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. From: krieger.jul...@gmail.com To: johnnyso...@hotmail.com CC: ccie_voice@onlinestudylist.com Hi Johnny, Even if the utils dbreplication commands do not show what we are looking for (2), does the replication work? Try to create a new region on the pub and see if it has replicated to the sub. Then try the following command on the sub to see if it worked : run sql select name from region If replication worked, you should see on your sub the newly created region Julien 2011/4/5 Johnny Soong johnnyso...@hotmail.com I ran into an issue with the Publisher. The DB Replication is broken. It is showing 3 in the state status. When i tried to issue the utils dbreplicate status. It said the following:Status cannot be performed when replication is down on the publisher, or on a cluster with a single active node; aborting replication status check operation. I did the utils dbreplic stop on the sub and then on the pub. Then i did the utils dbreplic reset 10.10.210.10 on the Pub. It didn't help. Replic is still showing 3 on the Pub. Sub is showing 2 which is fine. I can't issue utils dbreplic repair because the pub replic is down. I rebooted both servers. It didn't do any good. Any suggestion? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher.
i will take your advice next time when it happen. Just hope that this doesn't happen in the real lab. I spend 4 hrs troubleshooting this. Thanks. From: m...@mallalue.net To: johnnyso...@hotmail.com; krieger.jul...@gmail.com CC: ccie_voice@onlinestudylist.com Subject: RE: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. Date: Tue, 5 Apr 2011 20:53:45 + Johnny, Next time, try the following - On SUB : utils dbreplication stop - On PUB : utils dbreplication stop utils dbreplication clusterreset I’ve used the clusterreset successfully when repair and reset don’t work Mark. From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Johnny Soong Sent: 05 April 2011 19:03 To: krieger.jul...@gmail.com Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. i tried to change the extension on the phone. It did change. So i know replication is not working. I had to revert the configuration on the Callmanager to make it work. I don't know if there is a fix. Publisher replication is down. Repair wont work. Reboot didn't help. Reset doesn't do anything in this case. Since the Replic state is different. If both the Sub and Pub Rpl state is other than 2 and they are the same, then repair will work. Reset will work if you have diferrent repl state. I tried that already. Date: Tue, 5 Apr 2011 19:31:14 +0200 Subject: Re: [OSL | CCIE_Voice] callmanager datebasse replication issue with Publisher. From: krieger.jul...@gmail.com To: johnnyso...@hotmail.com CC: ccie_voice@onlinestudylist.com Hi Johnny, Even if the utils dbreplication commands do not show what we are looking for (2), does the replication work? Try to create a new region on the pub and see if it has replicated to the sub. Then try the following command on the sub to see if it worked : run sql select name from region If replication worked, you should see on your sub the newly created region Julien 2011/4/5 Johnny Soong johnnyso...@hotmail.com I ran into an issue with the Publisher. The DB Replication is broken. It is showing 3 in the state status. When i tried to issue the utils dbreplicate status. It said the following:Status cannot be performed when replication is down on the publisher, or on a cluster with a single active node; aborting replication status check operation. I did the utils dbreplic stop on the sub and then on the pub. Then i did the utils dbreplic reset 10.10.210.10 on the Pub. It didn't help. Replic is still showing 3 on the Pub. Sub is showing 2 which is fine. I can't issue utils dbreplic repair because the pub replic is down. I rebooted both servers. It didn't do any good. Any suggestion? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] rsvp issue with Unity Connection
Callmanager is set up with Unity Connectioon using skinny. RSVP Location Cac is set up to allow two calls between HQ and BR1 Site. RSVP setting is Optional. Codec between the two sites is ilbc. ip rsvp bandwidth 80 is assigned to each serial subinterface.The voicemail CTI ports are configured with HQ Device Pool. The phone i am using to access voicemail is configured with BR1 Device Pool. When i press the message button, I hear dead silence. When i call a HQ Phone, i can hear the phone ringing. But i picked up the call, i don't hear anything. sh sccp con output from hq router: HQ-RTR#$ 33558469 33554572 mtp sendrecv pass_th 10.10.210.1316676 18362 Unity Connection 33558469 33554571 mtp sendrecv pass_th 10.10.110.2 17198 18738 Loopback address of BR1 RTR BR1-RST show sccp conn output: BR1-RTR#$ sh sccp conn sess_idconn_idstype mode codec ripaddr rport sport 33558460 33554543 mtp sendrecv pass_th 192.168.10.14 26284 18364 My IP Phone 33558460 33554540 mtp sendrecv pass_th 10.10.110.1 18336 17644 Loopback address of HQ RTR HQ Router Configuration: HQ-RTR#sh Mar 30 06:46:08.587: %SYS-5-CONFIG_I: Configured from console by console HQ-RTR#sh runn Building configuration... Current configuration : 6642 bytes ! ! Last configuration change at 02:46:08 EDT Wed Mar 30 2011 ! NVRAM config last updated at 17:07:06 EDT Tue Mar 29 2011 ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname HQ-RTR ! boot-start-marker warm-reboot boot-end-marker ! logging buffered 51200 warnings ! no aaa new-model memory-size iomem 20 clock timezone EDT -5 clock summer-time EDT recurring network-clock-participate wic 0 network-clock-select 1 T1 0/0/0 dot11 syslog no ip source-route ! ! ip cef ! ! no ip domain lookup ip domain name proctorlabs.com ip multicast-routing ! multilink bundle-name authenticated ! isdn switch-type primary-ni ! voice-card 0 no dspfarm dsp services dspfarm ! ! ! voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! archive log config hidekeys ! ! ! ! controller T1 0/0/0 framing esf linecode b8zs pri-group timeslots 1-3,24 service mgcp ! controller T1 0/0/1 framing esf linecode b8zs channel-group 0 timeslots 1-24 ! ! class-map match-any AutoQoS-VoIP-Remark match ip dscp ef match ip dscp cs3 match ip dscp af31 class-map match-any AutoQoS-VoIP-Control-UnTrust match access-group name AutoQoS-VoIP-Control class-map match-any AutoQoS-VoIP-RTP-UnTrust match protocol rtp audio match access-group name AutoQoS-VoIP-RTCP ! ! policy-map AutoQoS-Policy-UnTrust class AutoQoS-VoIP-RTP-UnTrust priority 140 set dscp ef class AutoQoS-VoIP-Control-UnTrust bandwidth percent 10 set dscp cs3 class class-default fair-queue police rate percent 60 ! ! ! ! ! interface Loopback0 ip address 10.10.110.1 255.255.255.255 ! interface FastEthernet0/0 no ip address duplex full speed 100 ! interface FastEthernet0/0.10 encapsulation dot1Q 10 native ip address 10.10.100.1 255.255.255.0 ip pim dense-mode ! interface FastEthernet0/0.20 encapsulation dot1Q 20 ip address 10.10.200.3 255.255.255.0 ip helper-address 10.10.210.10 ip pim dense-mode h323-gateway voip interface h323-gateway voip id CUBE ipaddr 10.10.110.1 1719 h323-gateway voip h323-id HQ-RTR h323-gateway voip bind srcaddr 10.10.200.3 ! interface FastEthernet0/0.30 encapsulation dot1Q 30 ip address 10.10.210.1 255.255.255.0 ip pim dense-mode ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial0/0/0:23 no ip address encapsulation hdlc isdn switch-type primary-ni isdn incoming-voice voice isdn bind-l3 ccm-manager no cdp enable ! interface Serial0/0/1:0 no ip address encapsulation frame-relay frame-relay traffic-shaping frame-relay lmi-type ansi ip rsvp bandwidth ! interface Serial0/0/1:0.1 point-to-point bandwidth 768 ip address 10.10.111.1 255.255.255.0 ip ospf mtu-ignore snmp trap link-status frame-relay interface-dlci 201 class AutoQoS-FR-Se0/0/1:0-201 auto qos voip ip rsvp bandwidth 80 ! interface Serial0/0/1:0.2 point-to-point bandwidth 384 ip pim dense-mode ip ospf mtu-ignore snmp trap link-status frame-relay interface-dlci 202 ppp Virtual-Template199 class AutoQoS-FR-Se0/0/1:0-202 auto qos voip fr-atm ! interface Virtual-Template199 bandwidth 384 ip address 10.10.112.1 255.255.255.0 ppp multilink ppp multilink interleave ppp multilink fragment delay 10 ip rtp priority 16384 16383 128 ! router ospf 1 router-id 10.10.100.1 log-adjacency-changes network 10.10.0.0 0.0.255.255 area 0 ! ip
Re: [OSL | CCIE_Voice] rsvp issue with Unity Connection
codec g729r8 CC: ccie_voice@onlinestudylist.com From: rrcr...@yahoo.com Subject: Re: [OSL | CCIE_Voice] rsvp issue with Unity Connection Date: Tue, 29 Mar 2011 20:37:11 -0700 To: johnnyso...@hotmail.com What us your codec in your mtp? G729? Sent from my iPhone On Mar 29, 2011, at 8:02 PM, Johnny Soong johnnyso...@hotmail.com wrote: Callmanager is set up with Unity Connectioon using skinny. RSVP Location Cac is set up to allow two calls between HQ and BR1 Site. RSVP setting is Optional. Codec between the two sites is ilbc. ip rsvp bandwidth 80 is assigned to each serial subinterface.The voicemail CTI ports are configured with HQ Device Pool. The phone i am using to access voicemail is configured with BR1 Device Pool. When i press the message button, I hear dead silence. When i call a HQ Phone, i can hear the phone ringing. But i picked up the call, i don't hear anything. sh sccp con output from hq router: HQ-RTR#$ 33558469 33554572 mtp sendrecv pass_th 10.10.210.1316676 18362 Unity Connection 33558469 33554571 mtp sendrecv pass_th 10.10.110.2 17198 18738 Loopback address of BR1 RTR BR1-RST show sccp conn output: BR1-RTR#$ sh sccp conn sess_idconn_idstype mode codec ripaddr rport sport 33558460 33554543 mtp sendrecv pass_th 192.168.10.14 26284 18364 My IP Phone 33558460 33554540 mtp sendrecv pass_th 10.10.110.1 18336 17644 Loopback address of HQ RTR HQ Router Configuration: HQ-RTR#sh Mar 30 06:46:08.587: %SYS-5-CONFIG_I: Configured from console by console HQ-RTR#sh runn Building configuration... Current configuration : 6642 bytes ! ! Last configuration change at 02:46:08 EDT Wed Mar 30 2011 ! NVRAM config last updated at 17:07:06 EDT Tue Mar 29 2011 ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname HQ-RTR ! boot-start-marker warm-reboot boot-end-marker ! logging buffered 51200 warnings ! no aaa new-model memory-size iomem 20 clock timezone EDT -5 clock summer-time EDT recurring network-clock-participate wic 0 network-clock-select 1 T1 0/0/0 dot11 syslog no ip source-route ! ! ip cef ! ! no ip domain lookup ip domain name proctorlabs.com ip multicast-routing ! multilink bundle-name authenticated ! isdn switch-type primary-ni ! voice-card 0 no dspfarm dsp services dspfarm ! ! ! voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! archive log config hidekeys ! ! ! ! controller T1 0/0/0 framing esf linecode b8zs pri-group timeslots 1-3,24 service mgcp ! controller T1 0/0/1 framing esf linecode b8zs channel-group 0 timeslots 1-24 ! ! class-map match-any AutoQoS-VoIP-Remark match ip dscp ef match ip dscp cs3 match ip dscp af31 class-map match-any AutoQoS-VoIP-Control-UnTrust match access-group name AutoQoS-VoIP-Control class-map match-any AutoQoS-VoIP-RTP-UnTrust match protocol rtp audio match access-group name AutoQoS-VoIP-RTCP ! ! policy-map AutoQoS-Policy-UnTrust class AutoQoS-VoIP-RTP-UnTrust priority 140 set dscp ef class AutoQoS-VoIP-Control-UnTrust bandwidth percent 10 set dscp cs3 class class-default fair-queue police rate percent 60 ! ! ! ! ! interface Loopback0 ip address 10.10.110.1 255.255.255.255 ! interface FastEthernet0/0 no ip address duplex full speed 100 ! interface FastEthernet0/0.10 encapsulation dot1Q 10 native ip address 10.10.100.1 255.255.255.0 ip pim dense-mode ! interface FastEthernet0/0.20 encapsulation dot1Q 20 ip address 10.10.200.3 255.255.255.0 ip helper-address 10.10.210.10 ip pim dense-mode h323-gateway voip interface h323-gateway voip id CUBE ipaddr 10.10.110.1 1719 h323-gateway voip h323-id HQ-RTR h323-gateway voip bind srcaddr 10.10.200.3 ! interface FastEthernet0/0.30 encapsulation dot1Q 30 ip address 10.10.210.1 255.255.255.0 ip pim dense-mode ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial0/0/0:23 no ip address encapsulation hdlc isdn switch-type primary-ni isdn incoming-voice voice isdn bind-l3 ccm-manager no cdp enable ! interface Serial0/0/1:0 no ip address encapsulation frame-relay frame-relay traffic-shaping frame-relay lmi-type ansi ip rsvp bandwidth ! interface Serial0/0/1:0.1 point-to-point bandwidth 768 ip address 10.10.111.1 255.255.255.0 ip ospf mtu-ignore snmp trap link-status frame-relay interface-dlci 201 class AutoQoS-FR-Se0/0/1:0-201 auto qos voip ip rsvp bandwidth 80 ! interface Serial0/0/1:0.2 point-to-point bandwidth 384 ip pim dense-mode ip ospf mtu-ignore snmp trap link-status frame-relay interface-dlci 202 ppp Virtual-Template199 class AutoQoS-FR-Se0/0/1:0-202
[OSL | CCIE_Voice] issue with transcoder registering to the cme locally
I am having issue to get the transcoder to register with the cme locally. When i register it to the callmanager, it worked fine. NAME: PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 4, DESCR: PVDMII DSP SIMM with one DSP PID: PVDM2-16 , VID: NA , SN: FOC09160E5B NAME: PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 5, DESCR: PVDMII DSP SIMM with one DSP PID: PVDM2-16 , VID: V01 , SN: FOC10130MCT sccp local FastEthernet0/0.20sccp ccm 10.10.200.3 identifier 1 version 5.0.1 sccp ip precedence 3 sccp ! sccp ccm group 1 bind interface FastEthernet0/0.20 associate ccm 1 priority 1 associate profile 1 register hq-xcoder signaling dscp af31 ! dspfarm profile 1 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 maximum sessions 1 associate application SCCP telephony-service sdspfarm units 1 sdspfarm transcode sessions 1 sdspfarm tag 1 hq-xcoder ip source-address 10.10.200.3 port 2000 max-conferences 8 gain -6 transfer-system full-consult HQ-RTR#sh sds u mtp-1 Device:hq-xcoder TCP socket:[-1] UNREGISTERED actual_stream:0 max_stream 0 IP:0.0.0.0 0 Unknown 0 keepalive 0 max-mtps:1, max-streams:2, alloc-streams:0, act-streams:0 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] issue with transcoder registering to the cme locally
Yes. voice-card 0 no dspfarm dsp services dspfarm Date: Wed, 23 Feb 2011 13:34:50 -0600 Subject: Re: [OSL | CCIE_Voice] issue with transcoder registering to the cme locally From: whl...@gmail.com To: johnnyso...@hotmail.com CC: ccie_voice@onlinestudylist.com do you have a dsp farm? On Wed, Feb 23, 2011 at 12:07 PM, Johnny Soong johnnyso...@hotmail.com wrote: I am having issue to get the transcoder to register with the cme locally. When i register it to the callmanager, it worked fine. NAME: PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 4, DESCR: PVDMII DSP SIMM with one DSP PID: PVDM2-16 , VID: NA , SN: FOC09160E5B NAME: PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 5, DESCR: PVDMII DSP SIMM with one DSP PID: PVDM2-16 , VID: V01 , SN: FOC10130MCT sccp local FastEthernet0/0.20sccp ccm 10.10.200.3 identifier 1 version 5.0.1 sccp ip precedence 3 sccp ! sccp ccm group 1 bind interface FastEthernet0/0.20 associate ccm 1 priority 1 associate profile 1 register hq-xcoder signaling dscp af31 ! dspfarm profile 1 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 maximum sessions 1 associate application SCCP telephony-service sdspfarm units 1 sdspfarm transcode sessions 1 sdspfarm tag 1 hq-xcoder ip source-address 10.10.200.3 port 2000 max-conferences 8 gain -6 transfer-system full-consult HQ-RTR#sh sds u mtp-1 Device:hq-xcoder TCP socket:[-1] UNREGISTERED actual_stream:0 max_stream 0 IP:0.0.0.0 0 Unknown 0 keepalive 0 max-mtps:1, max-streams:2, alloc-streams:0, act-streams:0 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] issue with transcoder registering to the cme locally
Changed the name to hqxcoder without the dash in both Telephony-service and sccp ccm group association. Did a shut, no shut on the dspfarm profile. no sccp and sccp. Still not register. Look at show dspfarm all. Shown it is trying to associate. The question is why it trying. I also removed the version from sccp ccm. it didn't help. voice-card 0 no dspfarm dsp services dspfarm sccp local FastEthernet0/0.20 sccp ccm 10.10.200.3 identifier 1 version 5.0.1 sccp ip precedence 3 sccp or sccp local FastEthernet0/0.20 sccp ccm 10.10.200.3 identifier 1 sccp ip precedence 3 sccp sccp ccm group 1 bind interface FastEthernet0/0.20 associate ccm 1 priority 1 associate profile 1 register hqxcoder signaling dscp af31 ! dspfarm profile 1 transcode codec g711ulaw codec g729r8 maximum sessions 1 Telephony-service sdspfarm units 1 sdspfarm transcode sessions 1 sdspfarm tag 1 hqxcoder ip source-address 10.10.200.3 port 2000 max-conferences 8 gain -6 transfer-system full-consult associate application SCCP show sds units mtp-1 Device:hqxcoder TCP socket:[-1] UNREGISTERED actual_stream:0 max_stream 0 IP:0.0.0.0 0 Unknown 0 keepalive 0 max-mtps:1, max-streams:2, alloc-streams:0, act-streams:0 HQ-RTR#sh dspfarm all Dspfarm Profile Configuration Profile ID = 1, Service = TRANSCODING, Resource ID = 1 Profile Description : Profile Admin State : UP Profile Operation State : ACTIVE IN PROGRESS Application : SCCP Status : ASSOCIATION IN PROGRESS Resource Provider : FLEX_DSPRM Status : UP Number of Resource Configured : 1 Number of Resource Available : 1 Codec Configuration Codec : g711ulaw, Maximum Packetization Period : 30 Codec : g729r8, Maximum Packetization Period : 60 From: tih...@gmail.com To: johnnyso...@hotmail.com; ccie_voice@onlinestudylist.com Subject: RE: [OSL | CCIE_Voice] issue with transcoder registering to the cme locally Date: Wed, 23 Feb 2011 21:30:25 +0200 Try to remove – from name, let it hqxcode Best regards, Tamer Ismail From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Johnny Soong Sent: Wednesday, February 23, 2011 8:08 PM To: ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] issue with transcoder registering to the cme locally I am having issue to get the transcoder to register with the cme locally. When i register it to the callmanager, it worked fine. NAME: PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 4, DESCR: PVDMII DSP SIMM with one DSP PID: PVDM2-16 , VID: NA , SN: FOC09160E5B NAME: PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 5, DESCR: PVDMII DSP SIMM with one DSP PID: PVDM2-16 , VID: V01 , SN: FOC10130MCT sccp local FastEthernet0/0.20sccp ccm 10.10.200.3 identifier 1 version 5.0.1 sccp ip precedence 3 sccp ! sccp ccm group 1 bind interface FastEthernet0/0.20 associate ccm 1 priority 1 associate profile 1 register hq-xcoder signaling dscp af31 ! dspfarm profile 1 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 maximum sessions 1 associate application SCCP telephony-service sdspfarm units 1 sdspfarm transcode sessions 1 sdspfarm tag 1 hq-xcoder ip source-address 10.10.200.3 port 2000 max-conferences 8 gain -6 transfer-system full-consult HQ-RTR#sh sds u mtp-1 Device:hq-xcoder TCP socket:[-1] UNREGISTERED actual_stream:0 max_stream 0 IP:0.0.0.0 0 Unknown 0 keepalive 0 max-mtps:1, max-streams:2, alloc-streams:0, act-streams:0 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] issue with transcoder registering to the cme locally
It worked. You are the man. Thanks. CC: ccie_voice@onlinestudylist.com From: ron...@solcon.nl Subject: Re: [OSL | CCIE_Voice] issue with transcoder registering to the cme locally Date: Wed, 23 Feb 2011 21:36:14 +0100 To: johnnyso...@hotmail.com Hi, You need max-dn and max-ephone in your telephony-service Ron Op 23 feb. 2011 om 19:07 heeft Johnny Soong johnnyso...@hotmail.com het volgende geschreven: I am having issue to get the transcoder to register with the cme locally. When i register it to the callmanager, it worked fine. NAME: PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 4, DESCR: PVDMII DSP SIMM with one DSP PID: PVDM2-16 , VID: NA , SN: FOC09160E5B NAME: PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 5, DESCR: PVDMII DSP SIMM with one DSP PID: PVDM2-16 , VID: V01 , SN: FOC10130MCT sccp local FastEthernet0/0.20sccp ccm 10.10.200.3 identifier 1 version 5.0.1 sccp ip precedence 3 sccp ! sccp ccm group 1 bind interface FastEthernet0/0.20 associate ccm 1 priority 1 associate profile 1 register hq-xcoder signaling dscp af31 ! dspfarm profile 1 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 maximum sessions 1 associate application SCCP telephony-service sdspfarm units 1 sdspfarm transcode sessions 1 sdspfarm tag 1 hq-xcoder ip source-address 10.10.200.3 port 2000 max-conferences 8 gain -6 transfer-system full-consult HQ-RTR#sh sds u mtp-1 Device:hq-xcoder TCP socket:[-1] UNREGISTERED actual_stream:0 max_stream 0 IP:0.0.0.0 0 Unknown 0 keepalive 0 max-mtps:1, max-streams:2, alloc-streams:0, act-streams:0 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
Re: [OSL | CCIE_Voice] Calling to PSTN-WAN remote Zone
Can you ping the Remote GK ip address 10.10.100.2? From: ccie_voice-requ...@onlinestudylist.com Subject: CCIE_Voice Digest, Vol 60, Issue 134 To: ccie_voice@onlinestudylist.com Date: Tue, 22 Feb 2011 18:57:22 -0500 Send CCIE_Voice mailing list submissions to ccie_voice@onlinestudylist.com To subscribe or unsubscribe via the World Wide Web, visit http://onlinestudylist.com/mailman/listinfo/ccie_voice or, via email, send a message with subject or body 'help' to ccie_voice-requ...@onlinestudylist.com You can reach the person managing the list at ccie_voice-ow...@onlinestudylist.com When replying, please edit your Subject line so it is more specific than Re: Contents of CCIE_Voice digest... Today's Topics: 1. Calling to PSTN-WAN remote Zone (Jay Woods) -- Message: 1 Date: Tue, 22 Feb 2011 17:57:21 -0600 From: Jay Woods cisco...@live.com To: ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] Calling to PSTN-WAN remote Zone Message-ID: blu159-w239c3d121a36d8e4071639bd...@phx.gbl Content-Type: text/plain; charset=iso-8859-1 Hello Everyone, I'm having trouble calling the India number through the PSTN-WAN zone of the Gatekeeper. I have posted the relevant debugs below. HQ#debug gatek main 10 HQ# HQ# HQ# HQ# *Feb 22 22:26:57.538: ////GK/gk_process: QUEUE_EVENT (minor 0) wakeup *Feb 22 22:26:57.678: ////GK/gk_process: QUEUE_EVENT (minor 0) wakeup *Feb 22 22:27:01.758: ////GK/gk_process: QUEUE_EVENT (minor 0) wakeup *Feb 22 22:27:02.270: ////GK/gk_process: QUEUE_EVENT (minor 0) wakeup *Feb 22 22:27:02.270: ////GK/gk_rassrv_arq: arqp=0x4837F484,crv=0x3, answerCall=0 *Feb 22 22:27:02.270: ////GK/gk_rassrv_sep_arq: ARQ Didn't use GK_AAA_PROC *Feb 22 22:27:02.270: //802EE55D0300/802EE55D0300/GK/gk_dns_query: No Name servers *Feb 22 22:27:02.270: //802EE55D0300/802EE55D0300/GK/rassrv_get_addrinfo: (916745738932) Tech-prefix match failed. *Feb 22 22:27:02.270: //802EE55D0300/802EE55D0300/GK/rassrv_get_addrinfo: (916745738932) Matched zone prefix 91 and remainder 6745738932 *Feb 22 22:27:02.270: ////GK/gk_rassrv_get_ingress_network: returning default ingress network = 1 *Feb 22 22:27:02.270: //802EE55D0300/802EE55D0300/GK/rassrv_arq_select_viazone: about to check the source side, src_zonep=0x496E9808 *Feb 22 22:27:02.270: //802EE55D0300/802EE55D0300/GK/rassrv_arq_select_viazone: matched zone is US, and z_invianamelen=0 *Feb 22 22:27:02.270: //802EE55D0300/802EE55D0300/GK/rassrv_arq_select_viazone: about to check the destination side, dst_zonep=0x4A93A26C *Feb 22 22:27:02.270: //802EE55D0300/802EE55D0300/GK/rassrv_arq_select_viazone: matched zone is PSTN-WAN, and z_outvianamelen=0 *Feb 22 22:27:02.270: //802EE55D0300/802EE55D0300/GK/rassrv_get_addrinfo: No tech prefix *Feb 22 22:27:02.270: //802EE55D0300/802EE55D0300/GK/rassrv_get_addrinfo: Alias not found *Feb 22 22:27:02.270: //802EE55D0300/802EE55D0300/GK/rassrv_put_remote_zones_from_zone_list: zone PSTN-WAN *Feb 22 22:27:02.270: //802EE55D0300/802EE55D0300/GK/send_lrq: seq_lrq 1, use_be 0, rzone_cnt 1 *Feb 22 22:27:02.270: //802EE55D0300/802EE55D0300/GK/send_lrq: lrq array index 5, lap 4ABAE820 *Feb 22 22:27:02.270: //802EE55D0300/802EE55D0300/GK/send_lrq: sent lrq - zonecount 1 *Feb 22 22:27:02.542: ////GK/gk_process: got a TIMER event *Feb 22 22:27:02.542: ////GK/gk_handle_timers *Feb 22 22:27:02.542: ////GK/gk_handle_timers: managed timer expired 0x4762D750 *Feb 22 22:27:04.878: ////GK/gk_process: got a TIMER event *Feb 22 22:27:04.878: ////GK/gk_handle_timers *Feb 22 22:27:04.878: ////GK/gk_handle_timers: managed timer expired 0x4762D8F0 *Feb 22 22:27:05.270: ////GK/gk_process: got a TIMER event *Feb 22 22:27:05.270: ////GK/gk_handle_timers *Feb 22 22:27:05.270: ////GK/gk_handle_timers: managed timer expired 0x4ABAE830 *Feb 22 22:27:08.270: ////GK/gk_process: got a TIMER event *Feb 22 22:27:08.270: ////GK/gk_handle_timers *Feb 22 22:27:08.270: ////GK/gk_handle_timers: managed timer expired 0x4ABAE830 *Feb 22 22:27:08.270: //802EE55D0300/802EE55D0300/GK/gk_rassrv_sep_arq: LRQ suspension point failed (return code = 0x4009) HQ# HQ# HQ# HQ# debug h225 asn1 prefix dialedDigits : 1# } } } } } mc FALSE undefinedNode FALSE } gatekeeperIdentifier {US} endpointVendor { vendor { t35CountryCode 181 t35Extension 0 manufacturerCode 18 } } timeToLive 60
[OSL | CCIE_Voice] voicemail aar issue.
I ran a test with voice mail port with aar. I was able to dial the voicemail port # to get to unity connection system. But i can't dial the voicemail pilot number directly even though the hunt pilot # is configured with aar group and external mask. I think there is a bug with callmanager 7.01. Anybody ran into this issue before? Voice mail Port Configuration Status Status: Ready Device Information Registration Registered with Cisco Unified Communications Manager 10.10.210.11 IP Address 10.10.210.13 Port Name Description Device Pool HQ -- Not Selected -- BR1 MoH_G711_DP Common Device Configuration None Calling Search Space css-hq-international None css-TP css-aar css-ani-xformations css-br1-internal-911 css-br1-ld css-hq-ani-xformations css-hq-internal-911 css-manager-internal css-tp-aar AAR Calling Search Space css-aar None css-TP css-ani-xformations css-br1-internal-911 css-br1-ld css-hq-ani-xformations css-hq-internal-911 css-hq-international css-manager-internal css-tp-aar Location Hub_None br1-loc Device Security Mode Non Secure Voice Mail Port -- Not Selected -- Authenticated Voice Mail Port Encrypted Voice Mail Port Use Trusted Relay Point Off On Default Directory Number Information Directory Number Partition None pt-aar pt-aar-post-xlate pt-after-xlate pt-ani-xformations pt-br1-intl pt-br1-ld pt-br1-loc pt-hq-ani-xformations pt-hq-intl pt-hq-ld pt-hq-loc pt-internal pt-manager Calling Search Space css-hq-international None css-TP css-aar css-ani-xformations css-br1-internal-911 css-br1-ld css-hq-ani-xformations css-hq-internal-911 css-manager-internal css-tp-aar AAR Group hq-aar None br1-aar Internal Caller ID Display Internal Caller ID Display (ASCII format) External Number Mask Hunt Pilot Configuration Status Update successful Pattern Definition Hunt Pilot Route Partition None pt-aar pt-aar-post-xlate pt-after-xlate pt-ani-xformations pt-br1-intl pt-br1-ld pt-br1-loc pt-hq-ani-xformations pt-hq-intl pt-hq-ld pt-hq-loc pt-internal pt-manager Description Numbering Plan None NANP Route Filter None MLPP Precedence Executive Override Flash Override Flash Immediate Priority Routine Default Hunt List VoiceMail -- Not Selected -- (Edit) Route Option Route this pattern Block this pattern No Error Unallocated Number Call Rejected Number Changed Invalid Number Format Precedence Level Exceeded Provide Outside Dial Tone Urgent Priority Hunt Forward Settings Use Personal Preferences Destination Calling Search Space Forward Hunt No Answer or None css-TP css-aar css-ani-xformations css-br1-internal-911 css-br1-ld css-hq-ani-xformations css-hq-internal-911 css-hq-international css-manager-internal css-tp-aar Forward Hunt Busy or None css-TP css-aar css-ani-xformations css-br1-internal-911 css-br1-ld css-hq-ani-xformations css-hq-internal-911 css-hq-international css-manager-internal css-tp-aar Maximum Hunt Timer Calling Party Transformations Use Calling Party's External Phone Number Mask Calling Party Transform Mask Prefix Digits (Outgoing Calls) Calling Line ID Presentation Default Allowed Restricted Calling Name Presentation Default Allowed Restricted Calling Party Number Type Cisco CallManager Unknown National International Subscriber Calling Party Numbering Plan Cisco CallManager ISDN National Standard Private Unknown Connected Party Transformations Connected Line ID Presentation Default Allowed Restricted Connected Name Presentation Default Allowed Restricted Called Party Transformations Discard Digits None 10-10-Dialing 10-10-Dialing Trailing-# 11/10D-7D 11/10D-7D Trailing-# 11D-10D 11D-10D Trailing-# Intl TollBypass Intl TollBypass Trailing-# NoDigits PreAt PreAt 10-10-Dialing PreAt 10-10-Dialing Trailing-# PreAt 11/10D-7D PreAt 11/10D-7D Trailing-# PreAt 11D-10D PreAt 11D-10D Trailing-# PreAt IntlTollBypass PreAt IntlTollBypass Trailing-# PreAt Trailing-# PreDot PreDot 10-10-Dialing PreDot 10-10-Dialing Trailing-# PreDot 11/10D-7D PreDot 11/10D-7D Trailing-# PreDot 11D-10D PreDot 11D-10D Trailing-# PreDot IntlAccess IntlDirectDial PreDot IntlTollBypass PreDot IntlTollBypass Trailing-# PreDot Trailing-# Trailing-# Called Party Transform Mask Prefix Digits (Outgoing Calls) Called Party Number Type Cisco CallManager Unknown National International Subscriber Called Party Numbering Plan Cisco CallManager ISDN National Standard Private Unknown AAR Group Settings AAR Group hq-aar None br1-aar External Number Mask ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
[OSL | CCIE_Voice] FW: mobile connect on aar
I am working on AAR in lab 6a in ipexpert workbook 1. HQ phone is configured with Single Number Reach to send the call to PSTN Phone 2123942123.Noticed when i tried to call HQ phone from BR1 phone with CAC blocking the call, the call got rerouted over to the PSTN to the PSTN phone 2123942123 via the remote destination rerouting css. HQ phone didn't get the call, only PSTN phone did. It seems that AAR doesnt work with Single Number Reach. To test the hypothesis, I took out the aar css and aar group from BR1 phone and the call still got routed over to the PSTN phone. Is there any workaround to get AAR to work with Single Number Reach? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com