Package: installation-reports INSTALL REPORT
Debian-installer-version: grabbed from http://cdimage.debian.org/pub/cdimage-testing/sarge_d-i/i386/rc2/sarge-i386-netinst.iso the 10 Feb 2005 uname -a: Linux ralf 2.6.10ralf #4 Wed Feb 16 11:22:53 CET 2005 i686 GNU/Linux Date: 10 Feb 2005 02:30 PM GMT Method: How did you install? What did you boot off? If network install, from where? Proxied? Machine: Compaq Presario 2510EA Processor: Pentium 4 2400 Memory: 320MB (256MB + 64MB Shared Video Memory) Root Device: IDE /dev/hda4 Root Size/partition table: Disk /dev/hda: 60.0 GB, 60011642880 bytes 255 heads, 63 sectors/track, 7296 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/hda1 1869 3736 15004710 a5 FreeBSD (/mnt/bsd) /dev/hda2 3737 5604 15004710 83 Linux (/mnt/gentoo) /dev/hda3 5605 6202 4803435 82 Linux swap / Solaris (swap) /dev/hda4 * 6203 7296 8787555 83 Linux (/) Output of lspci and lspci -n: [~]# lspci 0000:00:00.0 Host bridge: ATI Technologies Inc: Unknown device cbb2 (rev 02) 0000:00:01.0 PCI bridge: ATI Technologies Inc PCI Bridge [IGP 340M] 0000:00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) 0000:00:06.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device (rev 02) 0000:00:07.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin IV] 0000:00:08.0 Modem: ALi Corporation M5457 AC'97 Modem Controller 0000:00:0a.0 CardBus bridge: O2 Micro, Inc. OZ6912 Cardbus Controller 0000:00:0c.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link) 0000:00:0f.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) 0000:00:10.0 IDE interface: ALi Corporation M5229 IDE (rev c4) 0000:00:11.0 Bridge: ALi Corporation M7101 Power Management Controller [PMU] 0000:00:12.0 Ethernet controller: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller 0000:01:05.0 VGA compatible controller: ATI Technologies Inc Radeon IGP 340M 0000:02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8180L 802.11b MAC (rev 20) [~]# lspci -n 0000:00:00.0 0600: 1002:cbb2 (rev 02) 0000:00:01.0 0604: 1002:7010 0000:00:02.0 0c03: 10b9:5237 (rev 03) 0000:00:06.0 0401: 10b9:5451 (rev 02) 0000:00:07.0 0601: 10b9:1533 0000:00:08.0 0703: 10b9:5457 0000:00:0a.0 0607: 1217:6972 0000:00:0c.0 0c00: 104c:8026 0000:00:0f.0 0c03: 10b9:5237 (rev 03) 0000:00:10.0 0101: 10b9:5229 (rev c4) 0000:00:11.0 0680: 10b9:7101 0000:00:12.0 0200: 100b:0020 0000:01:05.0 0300: 1002:4337 0000:02:00.0 0200: 10ec:8180 (rev 20) [~]# Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot worked: [O] Configure network HW: [O] Config network: [O] Detect CD: [O] Load installer modules: [O] Detect hard drives: [O] Partition hard drives: [O] Create file systems: [O] Mount partitions: [O] Install base system: [O] Install boot loader: [O] Reboot: [O] Comments/Problems: I had to use the ethernet card since ndiswrapper isn't configured during setup. Good job! ;)
