Bug#421219: Why in testing only
This package is included both in testing stable release. But this is not reported as stable, only reported as testing bug. Why? -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Bug#416210: linux-image-2.6.18-4-686: Hangs at initrd boot state [i386] dual PentiumIII chipset ServerWorks OSB4
Package: linux-image-2.6.18-4-686 Version: 2.6.18.dfsg.1-11 Severity: critical Justification: breaks the whole system System: fresh pure install, all tasks from tasksel. On install state I hadn't any problems, but next boot cause any big problem for me: Kernel 2.6.18-4-486 works ok, but it has only ONE processor support and is slower. Kernel 2.6.18-4-686 hangs at boot. I don't know how switch off SMP at boot for tests. both install selections SMP nonSMP uses both installed processors. I had this problem with -3- kernel version. Previous I don't remember, because I had not much time for tests, and I reinstalled system many times to find stable system. I didn't try remove one processor for test. I'll do it if it will be needed. System hanging is very strange. I can do ctrl+alt+del, I can scroll shift+pgup/pgdown. Maybe one thread is hang, and don't allow second thread (second processor) to continue boot process. After about 45 minutes system boot, but hangs on another step. Finally system start up, but is very unstable. A lot of processes have zombie status. It is impossible to down system properly. shutdown -h now didn't down the system for about 3 hours, but started this process corectly - changed init state i succesfully stopped some of daemons. To install correctly fresh system, I must look out for selecting 486 kernel version, because 686 strange hang at initrd/boot state. Bootloader is grub, booted as (hd0,1) or /dev/ida/c0d0p2, because on p1 is configuration partition. Making boot sector on c0d0 cause config partition unusable. Really config partition is DOS partition, accessed by BIOS. c0d0p2 has bootable flag. Booting cause no problems. Kernel initrd file are loaded initialized correctly. My needs: 1. I have two computers. Give me scheme for RS232 cable to save all startup log, and command for kernel to switch output to RS232. I can use minicom for getting messages. 2. I want temporarly switch off SMP on -686, try boot. 3. Maybe use 486 kernel version with SMP support If it don't take any effect, please help me remove kernel module by module, to find one that cause problem. I think, it's possible 3 ways for resolving: 1. SMP cause problem 2. 686 cause problem 3. Problem is in any kernel module compiled as SMP or 680 or both. Hardware: Serwer Compaq Proliant ML380 (without G1/G2/G3) Processors #1 PentiumIII Coopermine 933MHz #2 PentiumIII Coopermine 633MHz Memory 2x modules ECC SDRAM 133MHz RootFS on Compaq Smart Array 3200 (hardware raid controller) #1 volume /dev/ida/c0d0 raid5 conf compaq partition rootfs #2 volume /dev/ida/c0d1 raid5 swap other partitions both on 6x 9GB scsi hotplug hdds Motherboard SCSI controller: 2-channel NCR, supported by sym53c8xx kernel module, no devices. in the future streamer and hdds for backups will be connected IDE Chipset - ServerWorks OSB4. I know about troubles on drivers with 2.6.18 kernel versions. People on the Internet says, that previous laters kernels has no problems. Network: intel based en100, supported by e100 kernel module USB1.x port Graphics, some ATI All were tested (ram, mass storage, processors, peripherials) by compaq software (installed on configuration partition from SmartStart 5.50), additionaly by memtest86. There aren't any errors. server# lsmod Module Size Used by appletalk 30640 20 nfsd 196784 13 exportfs5376 1 nfsd nfs 196300 0 lockd 53256 3 nfsd,nfs nfs_acl 3584 2 nfsd,nfs sunrpc133820 11 nfsd,nfs,lockd,nfs_acl rfcomm 33180 0 l2cap 20100 5 rfcomm bluetooth 43108 4 rfcomm,l2cap nls_iso8859_1 4352 0 isofs 31928 0 udf72324 0 sg 30364 0 ppdev 8708 0 lp 10948 0 button 6800 0 ac 5252 0 battery 9732 0 ipv6 213856 25 dm_snapshot15644 0 dm_mirror 18000 0 dm_mod 48952 2 dm_snapshot,dm_mirror loop 14216 0 tsdev 7616 0 i2c_piix4 8204 0 parport_pc 31524 1 parport32200 3 ppdev,lp,parport_pc floppy 52004 0 shpchp 32796 0 pci_hotplug28088 1 shpchp i2c_core 19472 1 i2c_piix4 psmouse34568 0 serio_raw 6532 0 pcspkr 2816 0 sworks_agp 9120 0 agpgart29360 1 sworks_agp evdev 9088 1 ext3 116488 4 jbd47272 1 ext3 ide_cd 35616 0 cdrom 32416 1 ide_cd generic 5508 0 [permanent] cpqarray
Bug#406621: etch/install i386 hang after first reboot on Compaq ML370 with PIII proc
Package: installation-reports Severity: critical Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot worked:[O] Configure network HW: [O] Config network: [O] Detect CD: [O] Load installer modules: [E] Detect hard drives: [O] Partition hard drives: [O] Create file systems:[O] Mount partitions: [O] Install base system:[O] Install boot loader:[E] Reboot: [E] About Load installer modules, on floppy install is error when I select PC keyboard. On CD install it's ok. About install boot loader, select lilo generate error. Select grub works ok. About Reboot, only kernel is booting. It detect and load all needed modules for network, hard disk controller (hardware array) and IDE cdrom. Properly display maked partitions, and hang. No shell is available. I can only alt+ctrl+del to repeat reboot. About install. It's etch installer. I tryed floppy install and binary-1 bootable CD install. Result is the same. I selected allways kernel i686 without SMP. Once I selected i686-SMP, but result is the same. Hardware config: Server: Compaq ML370 without suffix G1,2,3 or 4 Memory: two modules 128MB/133MHz ECC. memtest86 does not report any errors (tested for 4 days non-stop) Processors: first PIII 966MHz/133MHz, second PIII 667MHz/133MHz (to prevent problems, i decided to remove second processor) Network: intel, supported by e100 kernel module. Works ok with DHCP and Static sets, I can install floppy boot with net install. Disc controller: For CDROM, IDE ServerWorks with 2 channels paralell ata For hard drives, Compaq Smart Array 3200 with 64MB RAM, useable for cache 56MB RAM, connected 6 disks SCSI hot pluggable 9.1GB 10kRPM, configured as one logical volume presented as physical device /dev/ida/c0d0 by kernel module cpqarray . I notice, bootable binary-1 debian/sarge works ok. network upgrade from fresh sarge install to eth works ok. I'll try boot installer with debug flag, and try lspci bot now I don't have this data. -- System Information: Debian Release: etch binary-1 current weekly image Architecture: i386 (i686) Kernel: Linux 2.6 Locale: LANG=pl_PL, LC_CTYPE=pl_PL (charmap=ISO-8859-2) -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Bug#390436: Cannot install because depended from non-exist package (etch)
Package: openoffice.org-gtk Version: 2.0.3-6 Severity: grave package is dependenced from libdbus-1-2, but this package not exists. package is default piece in graphical environment user task. -- System Information: Debian Release: testing/unstable APT prefers testing APT policy: (500, 'testing') Architecture: i386 (i686) Shell: /bin/sh linked to /bin/bash Kernel: Linux 2.6.17-2-686 Locale: LANG=pl_PL, LC_CTYPE=pl_PL (charmap=ISO-8859-2) -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Bug#390436: It's impossible to start all OpenOffice apps in Gnome
Package: openoffice.org Version: 2.0.3-6 Followup-For: Bug #390436 It's impossible to start all open office applications in Gnome environment. Cause is, not installed package openoffice.org-gnome. Gnome support is not installed, because is installation problem with openoffice.org-gtk. When I click any of openoffice application, this start is begin, and... at short time application end without display any window or alert/notice. end with nothing. it works ok in KDE environment. I tested it in fresh etch installation, started from first full installation Debian Woody CD (because actual etch floppy installer is failed, when access to hdd is done by cpqarray module, and I have not cd writer at this time) -- System Information: Debian Release: testing/unstable APT prefers testing APT policy: (500, 'testing') Architecture: i386 (i686) Shell: /bin/sh linked to /bin/bash Kernel: Linux 2.6.17-2-686 Locale: LANG=pl_PL, LC_CTYPE=pl_PL (charmap=ISO-8859-2) Versions of packages openoffice.org depends on: ii openoffice.org-base 2.0.3-6OpenOffice.org office suite - data ii openoffice.org-calc 2.0.3-6OpenOffice.org office suite - spre ii openoffice.org-core 2.0.3-6OpenOffice.org office suite archit ii openoffice.org-draw 2.0.3-6OpenOffice.org office suite - draw ii openoffice.org-impress2.0.3-6OpenOffice.org office suite - pres ii openoffice.org-java-common2.0.3-6OpenOffice.org office suite Java s ii openoffice.org-math 2.0.3-6OpenOffice.org office suite - equa ii openoffice.org-writer 2.0.3-6OpenOffice.org office suite - word openoffice.org recommends no packages. -- no debconf information -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
