Re: [Elecraft] Kpa500 lcd display issue

[Jack Brindle via Elecraft]

There is no serial command to change the LCD ADJ setting. However, you can 
reset the saved parameters by holding the EDIT button while powering up the KPA.

73,
Jack, W6FB



> On Apr 13, 2020, at 1:03 PM, Andy Durbin  wrote:
> 
> "All other front panel stuff works I suspect the buttons for the menu pwr
> current and temp work also but I cant tell since the lcd only shows test
> pattern."
> 
> The KPA500 display will show what looks like a test pattern if menu item LCD 
> ADJ is set to 100.   If it used to work you may have accidentally changed the 
> value. 
> 
> Adjusting it with the menu may be difficult if you can't read the display.  
> There may be an undocumented command to set this value or perhaps it can be 
> changed by loading a saved config file.
> 
> 73,
> Andy, k3wyc
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to jackbrin...@me.com 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

[Elecraft] Kpa500 lcd display issue

[Andy Durbin]

"All other front panel stuff works I suspect the buttons for the menu pwr
current and temp work also but I cant tell since the lcd only shows test
pattern."

The KPA500 display will show what looks like a test pattern if menu item LCD 
ADJ is set to 100.   If it used to work you may have accidentally changed the 
value. 

Adjusting it with the menu may be difficult if you can't read the display.  
There may be an undocumented command to set this value or perhaps it can be 
changed by loading a saved config file.

73,
Andy, k3wyc
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

Re: [Elecraft] Kpa500 lcd display issue

[Jack Brindle via Elecraft]

Wayne;

What are you calling  “test pattern”?  There is an LCD test in the system, but 
it is not available normally, and also not a settable configuration.
Give me more info and I’ll try to diagnose.

73!
Jack, W6FB


> On Apr 13, 2020, at 12:30 PM, Wayne Suite  wrote:
> 
> The lcd on the kpa 500 shows onlty test pattrrn except when I upgraded the
> firmware to version 1.54 from ver 1.38 today during the upgrade the lcu
> showed Mcu Load like it is suposed to do. When done the unit restarted and
> the damn test pattern is back all the time.
> 
> Prior to upgrading thr firmware I suspected the led driver chip U6
> PCF8576DT to be at fault since it has the power on reset function which I
> thought was causing the test pattern, now not so much.
> 
> Anyway it works 100% otherwise just have to monitor it from the pc port.
> All other front panel stuff works I suspect the buttons for the menu pwr
> current and temp work also but I cant tell since the lcd only shows test
> pattern.
> 
> Looking for Don or Wayne to comment I put in an email to the mothership
> yesterday with few details but today much happier I dont have a brick.
> 
> Wayne
> Kd5spx
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to jackbrin...@me.com 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

[Elecraft] Firmware 1.52 kpa500

[Wayne Suite]

The version notes said with this version the ability was provided to clear
all faults using the pc port. I have old old faults still in the log so I
want to clear them all so how do I do it through the pc port?

Tia
Wayne
Kd5spx
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

[Elecraft] Kpa500 lcd display issue

[Wayne Suite]

The lcd on the kpa 500 shows onlty test pattrrn except when I upgraded the
firmware to version 1.54 from ver 1.38 today during the upgrade the lcu
showed Mcu Load like it is suposed to do. When done the unit restarted and
the damn test pattern is back all the time.

Prior to upgrading thr firmware I suspected the led driver chip U6
PCF8576DT to be at fault since it has the power on reset function which I
thought was causing the test pattern, now not so much.

Anyway it works 100% otherwise just have to monitor it from the pc port.
All other front panel stuff works I suspect the buttons for the menu pwr
current and temp work also but I cant tell since the lcd only shows test
pattern.

Looking for Don or Wayne to comment I put in an email to the mothership
yesterday with few details but today much happier I dont have a brick.

Wayne
Kd5spx
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

Re: [Elecraft] K3 High SWR

[Bob McGraw K4TAX]

I've used this source for Bird elements and dummy loads with very good 
success.   Although most may be "used" they are guaranteed and he has a 
good return policy if needed.


Here is an example of a Bird 100 watt dummy load for $50.00 
DB4303B W/N-Male Connector (NOT  SMALLER DB4303 or G)   For an 
additional  $5.00 you can get the N to UHF adapter.

https://www.nm3e.com/loadSampler.htm#LoadSampler

I have no interest in the company or person, just a paying customer.  I 
offer this as another suggestion.


73

Bob, K4TAX



**

On 4/13/2020 12:21 PM, Walter Underwood wrote:

If you want to build a dummy load, I recommend the Oak Hills Research RFL-100 
kit for $50 (http://www.ohr.com/rfl100.htm). I took pictures while I was 
building mine. You can see those in this blog post.

https://observer.wunderwood.org/2016/12/31/building-a-dummy-load/

wunder
Walter Underwood
wun...@wunderwood.org
http://observer.wunderwood.org/  (my blog)


On Apr 13, 2020, at 10:02 AM, Chris Pinholster via Elecraft 
 wrote:

I recently moved and set up the same temporary Butternut vertical as I used in 
my previous restricted HOA location. (When this virus stuff is over and I can 
get help, a small tower and a decent antenna will be erected).

The K3 is factory built and does not have an ATU. I get a 99 high swr reading 
on every band the antenna is tuned for, I replaced coax and connectors three 
times. My Rig Expert analyzer shows swr below 2 on the two bands I wish to use, 
40m and 20m. In Tune the external P3000 shows swr below 2, however the K3 still 
shows 99.

I’ve looked through the archives and I can’t find the answer I was looking for. 
(one that didn’t require sending the radio back to the factory). I am hoping 
for an answer involving pilot error and an easy fix. The movers didn’t handle 
the radio, I white glove delivered it to the new house myself.

I don’t own a dummy load yet, having sold everything but the K3 when I went to 
an HOA restrictive community for five years.

Any help would be appreciated.

Chris Pinholster
k4...@mac.com



__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to wun...@wunderwood.org

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to rmcg...@blomand.net

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

Re: [Elecraft] K3 High SWR

[Grant Youngman]

Do you have the correct antenna selected on the K3?  ANT1/ANT2, etc.?

Grant NQ5T

> On Apr 13, 2020, at 1:02 PM, Chris Pinholster via Elecraft 
>  wrote:
> 
> I recently moved and set up the same temporary Butternut vertical as I used 
> in my previous restricted HOA location. (When this virus stuff is over and I 
> can get help, a small tower and a decent antenna will be erected).
> 
> The K3 is factory built and does not have an ATU. I get a 99 high swr reading 
> on every band the antenna is tuned for, I replaced coax and connectors three 
> times. My Rig Expert analyzer shows swr below 2 on the two bands I wish to 
> use, 40m and 20m. In Tune the external P3000 shows swr below 2, however the 
> K3 still shows 99.
> 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

Re: [Elecraft] K3 High SWR

[Walter Underwood]

If you want to build a dummy load, I recommend the Oak Hills Research RFL-100 
kit for $50 (http://www.ohr.com/rfl100.htm). I took pictures while I was 
building mine. You can see those in this blog post.

https://observer.wunderwood.org/2016/12/31/building-a-dummy-load/

wunder
Walter Underwood
wun...@wunderwood.org
http://observer.wunderwood.org/  (my blog)

> On Apr 13, 2020, at 10:02 AM, Chris Pinholster via Elecraft 
>  wrote:
> 
> I recently moved and set up the same temporary Butternut vertical as I used 
> in my previous restricted HOA location. (When this virus stuff is over and I 
> can get help, a small tower and a decent antenna will be erected).
> 
> The K3 is factory built and does not have an ATU. I get a 99 high swr reading 
> on every band the antenna is tuned for, I replaced coax and connectors three 
> times. My Rig Expert analyzer shows swr below 2 on the two bands I wish to 
> use, 40m and 20m. In Tune the external P3000 shows swr below 2, however the 
> K3 still shows 99.
> 
> I’ve looked through the archives and I can’t find the answer I was looking 
> for. (one that didn’t require sending the radio back to the factory). I am 
> hoping for an answer involving pilot error and an easy fix. The movers didn’t 
> handle the radio, I white glove delivered it to the new house myself.
> 
> I don’t own a dummy load yet, having sold everything but the K3 when I went 
> to an HOA restrictive community for five years.
> 
> Any help would be appreciated.
> 
> Chris Pinholster
> k4...@mac.com
> 
> 
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to wun...@wunderwood.org

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

[Elecraft] K3 High SWR

[Chris Pinholster via Elecraft]

I recently moved and set up the same temporary Butternut vertical as I used in 
my previous restricted HOA location. (When this virus stuff is over and I can 
get help, a small tower and a decent antenna will be erected).
 
The K3 is factory built and does not have an ATU. I get a 99 high swr reading 
on every band the antenna is tuned for, I replaced coax and connectors three 
times. My Rig Expert analyzer shows swr below 2 on the two bands I wish to use, 
40m and 20m. In Tune the external P3000 shows swr below 2, however the K3 still 
shows 99.

 I’ve looked through the archives and I can’t find the answer I was looking 
for. (one that didn’t require sending the radio back to the factory). I am 
hoping for an answer involving pilot error and an easy fix. The movers didn’t 
handle the radio, I white glove delivered it to the new house myself.

I don’t own a dummy load yet, having sold everything but the K3 when I went to 
an HOA restrictive community for five years.
 
Any help would be appreciated.

Chris Pinholster
k4...@mac.com



__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

Re: [Elecraft] KPA1500 Schematics

[Michael Walker]

Hi Scott

I am sure they will show up in time, however I suspect the K4 and Covid are
higher on the priority list.

73, Mike va3mw


On Mon, Apr 13, 2020 at 12:13 PM K9MA  wrote:

> A while ago, someone suggested that Elecraft would provide the KPA1500
> and other unreleased schematics to customers. That is not the case:
>
> "HI Scott,
> Thanks for contacting Elecraft.
>
> While the released schematics are posted on the Elecraft website, they
> do not yet include the KPA1500."
>
>
> 73,
> Scott K9MA
>
> --
> Scott  K9MA
>
> k...@sdellington.us
>
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to va...@portcredit.net
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

[Elecraft] KPA1500 Schematics

[K9MA]

A while ago, someone suggested that Elecraft would provide the KPA1500 
and other unreleased schematics to customers. That is not the case:


"HI Scott,
Thanks for contacting Elecraft.

While the released schematics are posted on the Elecraft website, they 
do not yet include the KPA1500."



73,
Scott K9MA

--
Scott  K9MA

k...@sdellington.us

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

[Elecraft] KP3A circuit ?

[Paul Kirley]

Erwin DK5EW sed:
Found out also that there is a brocken pin at the PA board at jumper at 
P68A male connector. This brocken pin still remains in the according 
female connector. So lots of problems.

***

Dear OM Erwin,

Information that may help you is in an Elecraft Note that is attached to 
this e-mail (but will not get to the reflector, so I have cced you 
directly).  Problems with pins carrying power to the KPA3 are pretty 
common.


The applicable note, KPA3 Power Connector Replacement Revision B, June 
30, 2017, used to be available on the Elecraft website.  But now the 
relevant webpage https://elecraft.com/pages/mods-notes-alerts is devoid 
of information.  I have no idea why this was done.


Because the gold-plated male and female connectors are fairly common 
components, it may be cheaper for you to obtain them in Germany rather 
than having them shipped from California.


73, Paul W8TM
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

Re: [Elecraft] k2 c45 capacitor

[Dave Van Wallaghen]

Carlos,

C45 is mounted on the back of the Control Board as part of the CW Keying 
Waveshaping modification. You can find the installation instructions for 
that mod on page 21 of the current K2 manual.


Hope this helps...

73,
Dave W8FGU

-- Original Message --
From: "carlos.p" 
To: elecraft@mailman.qth.net
Sent: 4/13/2020 9:19:33 AM
Subject: [Elecraft] k2 c45 capacitor


hi, on the partslist control board are 3 22ùf capacitors c
13,c32,c45  c45 seems not on the control board, i assume its deleted in
later pcb version..
carlos



--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to d...@w8fgu.com


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

Re: [Elecraft] KP3A circuit ?

[Erwin Witt - DK5EW]

Andy,
yes indeed I had a closer look and it seems that the left pin on P68A is by 
factory. I compared pictures of the pa board at google and there it is the same 
depend on board revision.

73's Erwin/DK5EW

Member of the Team of MMMonVHF
your premium VHF.DX resource in the internet can be found at:
http://www.MMMonVHF.de

Personal Homepage: http://www.dk5ew.com
 
70MHz.de - die deutsche 4m Seite: http://www.70mhz.de


Andy Durbin schrieb am 13.04.2020 14:21 (GMT +02:00):
> "Found out also that there is a brocken pin at the PA board at jumper at
> P68A
> male connector. This brocken pin still remains in the according female
> connector.
> So lots of problems."
> 
> I don't know this module but Elecraft "keys" some connectors by removing a
> male
> pin and plugging the corresponding female pin. Are you sure what you are
> seeing
> is not intended keying?
> 
> 73,
> Andy, k3wyc
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list:
> http://www.qsl.net/donate.html
> Message delivered to dk...@darc.de 
> 
> 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

[Elecraft] k2 c45 capacitor

[carlos.p]

hi, on the partslist control board are 3 22ùf capacitors c
13,c32,c45  c45 seems not on the control board, i assume its deleted in
later pcb version..
carlos



--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

[Elecraft] KP3A circuit ?

[Andy Durbin]

"Found out also that there is a brocken pin at the PA board at jumper at P68A 
male connector. This brocken pin still remains in the according female 
connector. So lots of problems."

I don't know this module but Elecraft "keys" some connectors by removing a male 
pin and plugging the corresponding female pin.  Are you sure what you are 
seeing is not intended keying?

73,
Andy, k3wyc
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

Re: [Elecraft] KP3A circuit ?

[Erwin Witt - DK5EW]

I have found now the circuit at the elecraft ftp server.

Found out also that there is a brocken pin at the PA board at jumper at P68A 
male connector. This brocken pin still remains in the according female 
connector. So lots of problems.

73's Erwin/DK5EW


Erwin Witt - DK5EW schrieb am 13.04.2020 10:41 (GMT +02:00):
> Does anybody has the circuit diagram of the KP3A module ? I have board
> revision
> C.
> 
> Thank you !
> 
> 73's Erwin/DK5EW
> 
> 
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list:
> http://www.qsl.net/donate.html
> Message delivered to dk...@darc.de 
> 
> 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

[Elecraft] KP3A circuit ?

[Erwin Witt - DK5EW]

Does anybody has the circuit diagram of the KP3A module ? I have board revision 
C.

Thank you !

73's Erwin/DK5EW



__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

Re: [Elecraft] chk braker ?

[Erwin Witt - DK5EW]

OK it was the backside fuse I pulled it in now.
When turning now the power knob K3 is switching off, voltage on ps is going 
down and K3 PA unit is getting quick vry hot.
Next is I disable pa unit.

73's Erwin/DK5EW

Member of the Team of MMMonVHF
your premium VHF.DX resource in the internet can be found at:
http://www.MMMonVHF.de

Personal Homepage: http://www.dk5ew.com
 
70MHz.de - die deutsche 4m Seite: http://www.70mhz.de


Erwin Witt - DK5EW schrieb am 13.04.2020 08:53 (GMT +02:00):
> Hi all,
> 
> one more question pse:
> 
> 
> I have seen in the display once a message when turning power knob named
> "chk
> breaker"
> Not sure if message name is correct it comes only ones and seldom.
> 
> Any idea on that ?
> 
> 73's Erwin/DK5EW
> 
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list:
> http://www.qsl.net/donate.html
> Message delivered to dk...@darc.de 
> 
> 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

[Elecraft] chk braker ?

[Erwin Witt - DK5EW]

Hi all,

one more question pse:


I have seen in the display once a message when turning power knob named "chk 
breaker"
Not sure if message name is correct it comes only ones and seldom.

Any idea on that ?

73's Erwin/DK5EW


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com