Re: [Elecraft] K3 Problems
You may have broke the DSP firmware by keeping a key pressed too long. Power down, remove from power for 30 seconds, then power up while holding the VFO button unfilled you hear a response from the speaker. Then try a reload. David KD4NUE Sent from my Verizon Wireless Phone - Reply message - From: chas chas...@gmail.com Date: Mon, Nov 26, 2012 03:41 Subject: [Elecraft] K3 Problems To: Gary Surrency g...@elecraft.com, k3supp...@elecraft.com, elecraft elecraft@mailman.qth.net Hi Gary, I was using text decode on transmit when suddenly very few of the buttons on the front panel of the K3 would perform their normal function. Some produced no response ie - MENU and CONFIG do not work at all, SUB does not work at all. Many buttons produce a response which is completely different from their intended function. The K3 is totally unusable. I tried to install the latest firmware and got the following on the K3 screen: E O2OCOC ERR DSE Firmware failed to load I now have a very expensive piece of equipment that is totally unusable. I have the KAT500 on order but I am wondering if I should cancel that order as I will not be able to use it. Can you please advise me of a way forward? 73 from Charles Rodgers - M0BIN __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Small HF amp suggestions
Try to find a Yaesu FL-110. David KD4NUE Sent from my Verizon Wireless Phone __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K2 SSB audio problem
FETS in low power amplifier? David KD4NUE Sent from my Verizon Wireless Phone - Reply message - From: George Winship, NC5G gwwa5...@hotmail.com Date: Sun, Oct 21, 2012 22:48 Subject: [Elecraft] K2 SSB audio problem To: elecraft@mailman.qth.net After 11 years of operating and many unsolicited reports of great audio, I am suddenly getting not so good reports from my K2/100. Present setup is K2/100, KAT100, KPA500, and resonant antennas on 75 and 40 meters. Very rarely do SSB on any other bands. Stations seem to have trouble describing the problem. Reports vary from fuzziness, distortion, to clipping. I bypassed the tuner and amp, hooking feed line directly to K2/100 and also turned the power down to ten watts to shut off the KPA100 and problem persists. No difference between MH2 and CM500 mics. These test were done with stations who know my rig and my voice. This is an early K2/100. All mods were done years ago to K2, SSB, and KPA100. Receive audio is unchanged. Visual inspection of boards look OK. As a further check, I connected my KX3 to amp and antennas with great results. Any suggestions? Thanks es 73, George, NC5G -- View this message in context: http://elecraft.365791.n2.nabble.com/K2-SSB-audio-problem-tp7564435.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Need a locksmith with the K3
Push the display button and see if that toggles it. David KD4NUEW Sent from my Verizon Wireless Phone - Reply message - From: Gary Smith g...@ka1j.com Date: Tue, Oct 16, 2012 08:27 Subject: [Elecraft] Need a locksmith with the K3 To: Elecraft@mailman.qth.net I've inadvertently activated a feature I need to undo. Last night I was making changes with config and it may have happened at that time but I'm locked on a frequency and can't seem to change it. When I move the sub receiver frequency with dial B, it shows me the voltage, time, PLL1, PLL2, temp and so on. The tell is the lock showing in the upper right corner of the LCD display above the mode indicator. I'm looking in the manual but haven't found the answer yet. What do I need to do to get unlocked? Thanks Gary KA1J __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html