Re: [Elecraft] 2 different 144MHz transveters and CAT selection
I have an unusual situation in that I have 2 different 2m transverters attached to my K3S. One system is a dual channel ME2T-XP and uses the SUB RX, this is only used for EME and it designated XV1. The second is used on tropo/terrestrial DX and contests and is an ME2T-ProII, this is XV2. If I use WSJT-X and use CAT I have a problem in that a CAT selection for 144MHz always chooses XV1 which is not what I want at all most of the time. There are gain and LO offset configurations that mean that using a switch in the IF is not ideal. Currently my solution is to set the RF frequency for XV1 to 70 MHz temporarily which always confuses me when I want to go on 2m EME. What would be ideal would be some way of setting the CAT XV priority from the front panel. I think that this must be a firmware update, its an easy one but of course would be low down the list. Using a K3 for QO100 operation, I set the display to 89. MHz, not 10489. MHz. Easier to type, and the frequency display doesn't get clobbered by useless digits. If I go to fine tune mode, the frequency still fits on the display. In similar vein, you could consider defining one of the transverters as 44.xxx MHz instead of 144.xxx MHz. I expect CAT will work then? But, I have my gripes with K3 and transverters. The K3 firmware is buggy: if you only define transverter bands to work on and switch off the HF bands, then the band-up and band-down switch behaves strange, selecting bands that I disabled (80m and 10m, both disabled). It should switch between transverter bands but doesn't. I reported this quite a while back but no planning was given to fix this (a trivial fix, especially useful for people using transverters) I wonder if Elecraft will ever fix this (given that all effort is now on K4), and frankly this doesn't bode well for the K4: if there is a K5, will the K4 stop getting fixes? Also, given that Elecraft stopped making transverters a long time ago, I'm hoping they will make the contents of U4 of the XV series available. This would allow my transverters to talk to the K3 using the AUX bus, and I can think of a few ways where this would improve integration. I've considered reverse-engineering but apart from Elecraft probably frowning on that, haven't had the time (yet). But, don't knock it, this is how the DSP option became available for the K2... 73, Geert Jan PE1HZG __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] 2 different 144MHz transveters and CAT selection
Henk, I looked at this issue and it is a K3/K3S issue. I was able to setup 2 transverters (XV1 and XV2) on the same band and switch between them when the band change was initiated from the K3 front panel. When a frequency is sent via RS232 connection, it appears the K3 wants to determine what band it should be on determined from the frequency. It begins this check without checking to determine if it does have a correct band already selected. The checking would appear to start with XV1, finding a “match” then switching to that band (XV1), even when XV2 is selected previously, and the frequency is correct. This is from my observation, and may be over simplified. The only solution I have determined is to access the config menu and turn XV1 OFF. XV2 will then be the first match for the frequency sent, and thus selected. I verified this issue using the RFSpace SDR-IQ and SpectraVue s/w, and in the K3 both XV1 and XV2 set for the 1296 band. 73 de Ben W4SC Sent from Mail for Windows 10 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] 2 different 144MHz transveters and CAT selection
I have the same K3s issue, however with the internal K144XV and an external dual rx 2 meter transverter. Besides CAT the same applies to the keyboard frequency input. I guess we have to live with it... 73 Henk PA0C -Oorspronkelijk bericht- Van: elecraft-boun...@mailman.qth.net Namens Conrad PA5Y Verzonden: woensdag 2 september 2020 15:08 Aan: elecraft@mailman.qth.net Onderwerp: [Elecraft] 2 different 144MHz transveters and CAT selection I have an unusual situation in that I have 2 different 2m transverters attached to my K3S. One system is a dual channel ME2T-XP and uses the SUB RX, this is only used for EME and it designated XV1. The second is used on tropo/terrestrial DX and contests and is an ME2T-ProII, this is XV2. If I use WSJT-X and use CAT I have a problem in that a CAT selection for 144MHz always chooses XV1 which is not what I want at all most of the time. There are gain and LO offset configurations that mean that using a switch in the IF is not ideal. Currently my solution is to set the RF frequency for XV1 to 70 MHz temporarily which always confuses me when I want to go on 2m EME. What would be ideal would be some way of setting the CAT XV priority from the front panel. I think that this must be a firmware update, its an easy one but of course would be low down the list. Something of a luxury problem I know. Maybe there is another way or something that I did not think of? Regards Conrad PA5Y __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to h...@kpnplanet.nl -- Dit e-mailbericht is gecontroleerd op virussen met Avast antivirussoftware. https://www.avast.com/antivirus __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] 2 different 144MHz transveters and CAT selection
Why not use the command “BN $” ?? This is a GET/SEL command, and has VFO select options. Reference Programmers manual. “BN 16” selects XVERTER 1 “BN 17” selects XVERTER 2 73 de Ben W4SC Sent from Mail for Windows 10 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] 2 different 144MHz transveters and CAT selection
I have an unusual situation in that I have 2 different 2m transverters attached to my K3S. One system is a dual channel ME2T-XP and uses the SUB RX, this is only used for EME and it designated XV1. The second is used on tropo/terrestrial DX and contests and is an ME2T-ProII, this is XV2. If I use WSJT-X and use CAT I have a problem in that a CAT selection for 144MHz always chooses XV1 which is not what I want at all most of the time. There are gain and LO offset configurations that mean that using a switch in the IF is not ideal. Currently my solution is to set the RF frequency for XV1 to 70 MHz temporarily which always confuses me when I want to go on 2m EME. What would be ideal would be some way of setting the CAT XV priority from the front panel. I think that this must be a firmware update, its an easy one but of course would be low down the list. Something of a luxury problem I know. Maybe there is another way or something that I did not think of? Regards Conrad PA5Y __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
