Re: [Elecraft] K3 / K3S Station setup question
At my house we have a three car garage. We turned the bay closest to the tower into a 10X15 radio room by filling in the floor with concrete, tiling the floor to match the house and adding a new wall 8 feet inside the roll up door. Add HVAC duct off the whole house system, run a 240 VAC circuit and repurpose the existing 110 VAC circuits and we are good to go. The remaining 8 foot space becomes storage with access from the original roll up door. 73 de na6m > On Sep 16, 2015, at 10:50,wrote: > > Hi All, > > My objective has always been (but rarely achieved) to just have a well suited > part of the house where my station could be housed. You would think, > considering the fact that most of the houses we have owned were fairly decent > in size, that there would be such a place therein. However, raising > children, and keeping the XYL happy, often tend to conflict with this > objective. As children grow, and eventually vacate their bedrooms, space may > become available, but more often than not it is not in the most advantageous > part of the house! Besides, children often come back, or at least come to > visit often! So, I usually get relegated to the garage! Finding a properly > designed/configured house is almost as difficult as just finding a house in a > neighborhood that doesn't discriminate against ham radio all together! The > bottom line is that I've yet to get to the point where I could concentrate on > efficient "configuration". I'm still looking for available space Oh, > and I sh ou > ld add this. Long ago my wife bought me a plaque to display wherever I did > set up my station. It reads "It takes a real expert to create a mess like > this!" > > Dave W7AQK > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to m...@stennett.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
Hi All, My objective has always been (but rarely achieved) to just have a well suited part of the house where my station could be housed. You would think, considering the fact that most of the houses we have owned were fairly decent in size, that there would be such a place therein. However, raising children, and keeping the XYL happy, often tend to conflict with this objective. As children grow, and eventually vacate their bedrooms, space may become available, but more often than not it is not in the most advantageous part of the house! Besides, children often come back, or at least come to visit often! So, I usually get relegated to the garage! Finding a properly designed/configured house is almost as difficult as just finding a house in a neighborhood that doesn't discriminate against ham radio all together! The bottom line is that I've yet to get to the point where I could concentrate on efficient "configuration". I'm still looking for available space Oh, and I shou ld add this. Long ago my wife bought me a plaque to display wherever I did set up my station. It reads "It takes a real expert to create a mess like this!" Dave W7AQK __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
When we moved to our current home in 2006, my ham stations and outside antenna took a primary consideration in even deciding on which property to choose. My nine sled dogs were the other primary consideration. We moved from a 5ac lot to 1-3/4ac of which about 1ac is not woods. But moving out of a 1955 owner-built house to a modern 1994 5-star energy home was a good move. In 1955 the area was wilderness and homesteads and nearly roadless. We now live on a lake. My ham shack occupies the 3rd bedroom and is about 11x12 foot. I arranged the two 6-foot folding table in a L-configuration with about 30-inch space between one table and the closet. The closet became a bookshelf. The other table backs to the wall and only window and I have to racks at right angle to the other end of that table so the station forms a U. On the fourth wall is my workbench for electronic assembly. Pretty crowded, now. But leaving the table with space behind holding all the radio equipment makes cable work easier. Thru wall cable opening is at the end of the walkspace. Photos can be seen on my website. My dream shack is a 26 by 18 foot addition to the 2-car garage (separate shop) which I will place my metal/wood working tools in the front third and shack in back 2/3 with dividing wall between and either folding door or pocket door to keep dust from the front area getting to the electronics. This will place the shack facing my 50-foot eme tower about 40-foot away for shorter cables. But my dish is off the other end of the house so farther cable run. I need TV cams for watching the dish even from the current shack so new shack would not be substantially different in operation. But probably need about $25K or more for the dream shack - so still dreaming! 73, Ed - KL7UW http://www.kl7uw.com "Kits made by KL7UW" Dubus Mag business: dubus...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
I have two 24" monitors mounted on the wall behind my K Line. There is room to put my SEC1235M on top of the K3, the KAT500 on top of the KPA500 without blocking the ergonomically mounted monitors. To the left is my NCC-1 with a Steppir SDA-100 on top, and to the left of that my RCS12 on top of a GHE rotor RT-11. That still leaves room for a (soon) NUC to sit on top of the P3 to be the shack computer replacing the monster on the floor. BTW, the K3S made for a very nice reduction in mess behind the rig with the builtin preamp and USB connection. 73 jim ab3cv __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
It seems like my shack is in a constant state of reconfiguration. Then I had to complicate things by buying a K3S and a Flex-6700 at the Huntsville Hamfest. My initial plan was to build a "horseshoe" configuration; much like the computer room at a former office. Over time the XYL, who was a Geology/Earth Science professor, covered three of the four walls with six-foot-tall bookcases. Now that she has passed, I have the task of selling/donating all of her book collection. Eventually I will be able to reclaim the space and have the configuration that I wanted in the first place. There is no option to build vertically from the operating desk, as that would block the view from the only window in the room. 73 de Jim - AD6CW On 9/15/2015 6:11 AM, Bob McGraw - K4TAX wrote: I build furniture as one of my hobbies. Therefore I could build a custom, made to fit, each piece of equipment enclosure or desk. However, my station is in a reconfigured built in book case system. Cabinets are located below with doors, and above, shelves are extended to depths of 12" to 18" for equipment and operation, extend to the ceiling. Plus it is some 6 ft wide. A series of holes in each shelf allows running cables left to right and up and down. Over some 20 years it has contained and supported various pieces of equipment from a fully configured Collins S Line plus a 5 transceiver accumulation and now down to two transceivers and one amplifier and tuner.Being on the 2nd floor of the house, all feed lines and rotor control traverse the attic and drop down through the ceiling to the tuner and coax switch arrangement at the operating position. The point being.flexibility is a must with any installation and configuration. 73 Bob, K4TAX K3S s/n 10,163 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
Don, When will they announce a ham-oriented, antenna-equipped motor home? :-) Gary may be very disappointed not to have heard about that one early! 73, Phil W7OX On 9/15/15 6:12 AM, Don Wilhelm wrote: Sorry that you were not previously informed. For the record, Elecraft will be announcing something new in the future that will impact the space required for your station. The size may vary from one inch wide to 19 inches (rack mount), and will vary in height from one inch to 24 inches. Now you have been informed about the size of future Elecraft products. Make your desk plans suitable for that expansion.:-) 73, Don W3FPR On 9/15/2015 8:48 AM, Gary wrote: Humphi just completed a nice desk in the motor home. Why was I not informed that it needed to be wider to allow for a new external speaker? Pretty ordinary communication from Elecraft I reckon. I should have been given a heads up. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
Jim / all I found these small 3” disks at the local ACE Hardware it assists the table to glide across the floor… I needed 6 to make it easy to glide the desk. Frank KG9H > On Sep 15, 2015, at 11:15 AM, Jim Brownwrote: > > On Tue,9/15/2015 6:20 AM, Cady, Fred wrote: >> Build it so you can get behind the desk to connect things up. You should >> see the back of my desk! > > YES! I have the same problem -- my desk is anchored to the wall, with a few > inches between desk and wall for cables to pass to shelves above and below. > If I were starting from scratch, I would put the desk and shelves on wheels > that I could get behind. > > 73, Jim K9YC > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to kg9hfr...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
FINALLY - I got out the camera and took a photo of my desk setup. I haven’t put it on QRZ yet - may do something different over there. But for now, look at my web site under “My Equipment”. Right at the top is a shot of the desk and a description of what’s on top. Http://www.w6jhb.com <http://www.w6jhb.com/> BTW - I also added a handful of new QSL’s to the “Favorite QSL’s” link - some are pretty cool!! 73, Jim / W6JHB > On Monday, Sep 14, 2015, at Monday, 1:00 PM, Jerry Moore > <je...@carolinaheli.com> wrote: > > Any pictures? QRZ and your personal site are missing pics of your setup :) > > -Original Message- > From: James Bennett [mailto:w6...@me.com] > Sent: Monday, September 14, 2015 3:50 PM > To: ae...@carolinaheli.com > Cc: Elecraft Reflector Reflector > Subject: Re: [Elecraft] K3 / K3S Station setup question > > Jerry, > > I’m also a righty and built part of my desk / operating setup. Mine is a > little different, as I have a 27” iMac - sitting off to the left. But here’s > what my setup is like: > > - A 54” wide, 24” deep double pedestal desk with a solid core 80” wide x 32” > deep door sitting on top. This gives me a w-i-d-e operating surface. > > - The iMac sits off to the left. > > On top I build a double high “riser” out of 3/4” oak plywood, faced with oak > strips.; the bottom riser is 4-1/2” high x 48” wide. Under it are my two > Begali keys - a paddle and a straight key. Also gives me room to slide my > wireless keyboard and track pad underneath when not in use. > > The upper riser is 5-1/2” high x 20” wide and sits on the left end of the > lower riser, basically directly in front of me. Sitting on the second level > (the top of the long riser) are, from left to right: K3, P3, KPA500, homebrew > 144 MHz 80 watt amp, and an MFJ-4245MV power supply. My KAT500 tuner sits > atop the KPA500. This arrangement puts the K3/P3 directly in front of me, and > allows me to move the keys around on the desk under them as I want. > > On top of that third level, the upper riser, I have sitting an ASUS 23” > second monitor, a KX3, and my Tascam external sound card. > > The upper surface of each riser is covered by black, non-stick, rubberized, > “shelf paper” I got at a fabric store. Keeps stuff from sliding around. > > I like having the K3/P3 directly in front of me and the keys under them. I > previously had this equipment in place without any risers and was not 100% > happy with the layout or the ability to use the equipment easily. > > Jim / W6JHB __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
On Tue,9/15/2015 6:20 AM, Cady, Fred wrote: Build it so you can get behind the desk to connect things up. You should see the back of my desk! YES! I have the same problem -- my desk is anchored to the wall, with a few inches between desk and wall for cables to pass to shelves above and below. If I were starting from scratch, I would put the desk and shelves on wheels that I could get behind. 73, Jim K9YC __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
Don, Thank you for the heads up. I will save up for a 40 footer Chuckle Gary -Original Message- From: "Don Wilhelm" <w3...@embarqmail.com> Sent: 15/09/2015 11:15 PM To: "elecraft@mailman.qth.net" <elecraft@mailman.qth.net> Subject: Re: [Elecraft] K3 / K3S Station setup question Sorry that you were not previously informed. For the record, Elecraft will be announcing something new in the future that will impact the space required for your station. The size may vary from one inch wide to 19 inches (rack mount), and will vary in height from one inch to 24 inches. Now you have been informed about the size of future Elecraft products. Make your desk plans suitable for that expansion.:-) 73, Don W3FPR On 9/15/2015 8:48 AM, Gary wrote: > Humphi just completed a nice desk in the motor home. > Why was I not informed that it needed to be wider to allow for a new external > speaker? > > Pretty ordinary communication from Elecraft I reckon. I should have been > given a heads up. > > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to vk1zzg...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
Phil, I'm in. Ya think Wayne would like the specifications of my Mosely beam for it's incorporation? Hope Wayne puts me at the top of the list as a field tester. (grin) Gary -Original Message- From: "Phil Wheeler" <w...@socal.rr.com> Sent: 16/09/2015 1:29 AM To: "elecraft@mailman.qth.net" <elecraft@mailman.qth.net> Subject: Re: [Elecraft] K3 / K3S Station setup question Don, When will they announce a ham-oriented, antenna-equipped motor home? :-) Gary may be very disappointed not to have heard about that one early! 73, Phil W7OX On 9/15/15 6:12 AM, Don Wilhelm wrote: > Sorry that you were not previously informed. > > For the record, Elecraft will be announcing > something new in the future that will impact the > space required for your station. The size may > vary from one inch wide to 19 inches (rack > mount), and will vary in height from one inch to > 24 inches. > > Now you have been informed about the size of > future Elecraft products. Make your desk plans > suitable for that expansion.:-) > > 73, > Don W3FPR > > On 9/15/2015 8:48 AM, Gary wrote: >> Humphi just completed a nice desk in the >> motor home. >> Why was I not informed that it needed to be >> wider to allow for a new external speaker? >> >> Pretty ordinary communication from Elecraft I >> reckon. I should have been given a heads up. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to vk1zzg...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
Makes sense. I'm just hoping to go UP if needed or maybe adding small toggles under the shelf that extend antenna rotator controls if I get that far. At this point I'm debating a 4 square setup for 160/80/(?40) homebrew until I'm at the point to do something better. That gives me some experimentation projects to work on. 160/80/40 due to the sunspots being low. Those bands should be optimal I'd think. Jer -Original Message- From: David Cole [mailto:d...@nk7z.net] Sent: Tuesday, September 15, 2015 8:39 AM To: Jerry Moore Cc: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3 / K3S Station setup question Hi, Just making the point that as things are added, you will need more space... I once built a tight cabinet like that, and within a year, it was too small... -- Thanks and 73's, For equipment, and software setups and reviews see: www.nk7z.net For MixW support see; http://groups.yahoo.com/neo/groups/mixw/info For Dopplergram information see: http://groups.yahoo.com/neo/groups/dopplergram/info For MM-SSTV see: http://groups.yahoo.com/neo/groups/MM-SSTV/info On Mon, 2015-09-14 at 21:13 -0400, Jerry Moore wrote: > That will likely go on top when I get it eventually :) > > -Original Message- > From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of > David Cole > Sent: Monday, September 14, 2015 3:55 PM > To: elecraft@mailman.qth.net > Subject: Re: [Elecraft] K3 / K3S Station setup question > > What about the new Speaker? :) > -- > Thanks and 73's, > For equipment, and software setups and reviews see: > www.nk7z.net > > For MixW support see; > http://groups.yahoo.com/neo/groups/mixw/info > For Dopplergram information see: > http://groups.yahoo.com/neo/groups/dopplergram/info > For MM-SSTV see: > http://groups.yahoo.com/neo/groups/MM-SSTV/info > > > On Mon, 2015-09-14 at 15:28 -0400, ae...@carolinaheli.com wrote: > > It's been a while and I'm a huge proponent of measure twice cut once. > > I'm building a hutch for my operating desk. The desk is 4' wide x > > 28" deep > (2' > > 4"). I'm right handed and my primary mode will be CW. I have both a > > Bencher paddle and a generic straight key. I need about 18" wide for > > my K3S and future P3. The K3S is 10"x10"x7.25"(stand extended and > > air gap > above it. > > Planning to use a 1 x or 2 x 12 for the shelf and 1x for the > > vertical supports. > > > > Not sure on right to left arrangement with me sitting in the middle. > > Was thinking keys, then P3, then radio, then space to the left. > > Allowing 3/4" for the end support, 9 inches for the keys to store, > > 3/4" for a vertical support, then 18" or so for the P3, then K3S, > > the > > 3/4 for vertical Support. That brings me 29.25" from the Right edge > > leaving 18" (if we subtract 3/4" for the end vertical support) for > > the Eventual AMP. If I eventually get the External antenna tuner it > > will go on top of the shelf or on top of the amp directly if it will fit. > > > > Does this sound like a proper setup to operate CW with the arm on > > the desk..etc.. turn dials with the left hand..etc.. I'll have a > > laptop/monitors on top of the shelf and a smallish keyboard/mouse on > > the > desktop. > > > > Just trying to get it all worked out so I don't have to remake this > > thing several times.. why re-invent the wheel when someone has > > already done it right? > > > > Thanks in advance. > > Jerry Moore > > K3S SN# TBA Wednesday > > > > __ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:Elecraft@mailman.qth.net > > > > This list hosted by: http://www.qsl.net Please help support this > > email > > list: http://www.qsl.net/donate.html Message delivered to > > d...@nk7z.net > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net Please help support this email > list: http://www.qsl.net/donate.html Message delivered to > je...@carolinaheli.com > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
I build furniture as one of my hobbies. Therefore I could build a custom, made to fit, each piece of equipment enclosure or desk. However, my station is in a reconfigured built in book case system. Cabinets are located below with doors, and above, shelves are extended to depths of 12" to 18" for equipment and operation, extend to the ceiling. Plus it is some 6 ft wide. A series of holes in each shelf allows running cables left to right and up and down. Over some 20 years it has contained and supported various pieces of equipment from a fully configured Collins S Line plus a 5 transceiver accumulation and now down to two transceivers and one amplifier and tuner.Being on the 2nd floor of the house, all feed lines and rotor control traverse the attic and drop down through the ceiling to the tuner and coax switch arrangement at the operating position. The point being.flexibility is a must with any installation and configuration. 73 Bob, K4TAX K3S s/n 10,163 On 9/15/2015 7:38 AM, David Cole wrote: Hi, Just making the point that as things are added, you will need more space... I once built a tight cabinet like that, and within a year, it was too small... __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
Build it so you can get behind the desk to connect things up. You should see the back of my desk! 73, Fred KE7X -Original Message- From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of David Cole Sent: Tuesday, September 15, 2015 6:39 AM To: Jerry Moore Cc: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3 / K3S Station setup question Hi, Just making the point that as things are added, you will need more space... I once built a tight cabinet like that, and within a year, it was too small... -- Thanks and 73's, For equipment, and software setups and reviews see: www.nk7z.net For MixW support see; http://groups.yahoo.com/neo/groups/mixw/info For Dopplergram information see: http://groups.yahoo.com/neo/groups/dopplergram/info For MM-SSTV see: http://groups.yahoo.com/neo/groups/MM-SSTV/info On Mon, 2015-09-14 at 21:13 -0400, Jerry Moore wrote: > That will likely go on top when I get it eventually :) > > -Original Message- > From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of > David Cole > Sent: Monday, September 14, 2015 3:55 PM > To: elecraft@mailman.qth.net > Subject: Re: [Elecraft] K3 / K3S Station setup question > > What about the new Speaker? :) > -- > Thanks and 73's, > For equipment, and software setups and reviews see: > www.nk7z.net > > For MixW support see; > http://groups.yahoo.com/neo/groups/mixw/info > For Dopplergram information see: > http://groups.yahoo.com/neo/groups/dopplergram/info > For MM-SSTV see: > http://groups.yahoo.com/neo/groups/MM-SSTV/info > > > On Mon, 2015-09-14 at 15:28 -0400, ae...@carolinaheli.com wrote: > > It's been a while and I'm a huge proponent of measure twice cut once. > > I'm building a hutch for my operating desk. The desk is 4' wide x > > 28" deep > (2' > > 4"). I'm right handed and my primary mode will be CW. I have both a > > Bencher paddle and a generic straight key. I need about 18" wide for > > my K3S and future P3. The K3S is 10"x10"x7.25"(stand extended and > > air gap > above it. > > Planning to use a 1 x or 2 x 12 for the shelf and 1x for the > > vertical supports. > > > > Not sure on right to left arrangement with me sitting in the middle. > > Was thinking keys, then P3, then radio, then space to the left. > > Allowing 3/4" for the end support, 9 inches for the keys to store, > > 3/4" for a vertical support, then 18" or so for the P3, then K3S, > > the > > 3/4 for vertical Support. That brings me 29.25" from the Right edge > > leaving 18" (if we subtract 3/4" for the end vertical support) for > > the Eventual AMP. If I eventually get the External antenna tuner it > > will go on top of the shelf or on top of the amp directly if it will fit. > > > > Does this sound like a proper setup to operate CW with the arm on > > the desk..etc.. turn dials with the left hand..etc.. I'll have a > > laptop/monitors on top of the shelf and a smallish keyboard/mouse on > > the > desktop. > > > > Just trying to get it all worked out so I don't have to remake this > > thing several times.. why re-invent the wheel when someone has > > already done it right? > > > > Thanks in advance. > > Jerry Moore > > K3S SN# TBA Wednesday > > > > __ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:Elecraft@mailman.qth.net > > > > This list hosted by: http://www.qsl.net Please help support this > > email > > list: http://www.qsl.net/donate.html Message delivered to > > d...@nk7z.net > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net Please help support this email > list: http://www.qsl.net/donate.html Message delivered to > je...@carolinaheli.com > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to fc...@ece.montana.edu __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
Humphi just completed a nice desk in the motor home. Why was I not informed that it needed to be wider to allow for a new external speaker? Pretty ordinary communication from Elecraft I reckon. I should have been given a heads up. Sigh. Gary -Original Message- From: "David Cole" <d...@nk7z.net> Sent: 15/09/2015 10:39 PM To: "Jerry Moore" <je...@carolinaheli.com> Cc: "elecraft@mailman.qth.net" <elecraft@mailman.qth.net> Subject: Re: [Elecraft] K3 / K3S Station setup question Hi, Just making the point that as things are added, you will need more space... I once built a tight cabinet like that, and within a year, it was too small... -- Thanks and 73's, For equipment, and software setups and reviews see: www.nk7z.net For MixW support see; http://groups.yahoo.com/neo/groups/mixw/info For Dopplergram information see: http://groups.yahoo.com/neo/groups/dopplergram/info For MM-SSTV see: http://groups.yahoo.com/neo/groups/MM-SSTV/info On Mon, 2015-09-14 at 21:13 -0400, Jerry Moore wrote: > That will likely go on top when I get it eventually :) > > -Original Message- > From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of David > Cole > Sent: Monday, September 14, 2015 3:55 PM > To: elecraft@mailman.qth.net > Subject: Re: [Elecraft] K3 / K3S Station setup question > > What about the new Speaker? :) > -- > Thanks and 73's, > For equipment, and software setups and reviews see: > www.nk7z.net > > For MixW support see; > http://groups.yahoo.com/neo/groups/mixw/info > For Dopplergram information see: > http://groups.yahoo.com/neo/groups/dopplergram/info > For MM-SSTV see: > http://groups.yahoo.com/neo/groups/MM-SSTV/info > > > On Mon, 2015-09-14 at 15:28 -0400, ae...@carolinaheli.com wrote: > > It's been a while and I'm a huge proponent of measure twice cut once. > > I'm building a hutch for my operating desk. The desk is 4' wide x 28" deep > (2' > > 4"). I'm right handed and my primary mode will be CW. I have both a > > Bencher paddle and a generic straight key. I need about 18" wide for > > my K3S and future P3. The K3S is 10"x10"x7.25"(stand extended and air gap > above it. > > Planning to use a 1 x or 2 x 12 for the shelf and 1x for the vertical > > supports. > > > > Not sure on right to left arrangement with me sitting in the middle. > > Was thinking keys, then P3, then radio, then space to the left. > > Allowing 3/4" for the end support, 9 inches for the keys to store, > > 3/4" for a vertical support, then 18" or so for the P3, then K3S, the > > 3/4 for vertical Support. That brings me 29.25" from the Right edge > > leaving 18" (if we subtract 3/4" for the end vertical support) for the > > Eventual AMP. If I eventually get the External antenna tuner it will > > go on top of the shelf or on top of the amp directly if it will fit. > > > > Does this sound like a proper setup to operate CW with the arm on the > > desk..etc.. turn dials with the left hand..etc.. I'll have a > > laptop/monitors on top of the shelf and a smallish keyboard/mouse on the > desktop. > > > > Just trying to get it all worked out so I don't have to remake this > > thing several times.. why re-invent the wheel when someone has already > > done it right? > > > > Thanks in advance. > > Jerry Moore > > K3S SN# TBA Wednesday > > > > __ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:Elecraft@mailman.qth.net > > > > This list hosted by: http://www.qsl.net Please help support this email > > list: http://www.qsl.net/donate.html Message delivered to > > d...@nk7z.net > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html Message > delivered to je...@carolinaheli.com > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to vk1zzg...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
Jer, Dammit, why didn't I think of that. (grin) Gary -Original Message- From: "ae...@carolinaheli.com" <ae...@carolinaheli.com> Sent: 15/09/2015 10:56 PM To: "'Gary'" <vk1zzg...@gmail.com>; "d...@nk7z.net" <d...@nk7z.net> Cc: "elecraft@mailman.qth.net" <elecraft@mailman.qth.net> Subject: RE: [Elecraft] K3 / K3S Station setup question You COULD just buy a larger motor home :D Jer From: Gary [mailto:vk1zzg...@gmail.com] Sent: Tuesday, September 15, 2015 8:49 AM To: d...@nk7z.net; Jerry Moore Cc: elecraft@mailman.qth.net Subject: RE: [Elecraft] K3 / K3S Station setup question Humphi just completed a nice desk in the motor home. Why was I not informed that it needed to be wider to allow for a new external speaker? Pretty ordinary communication from Elecraft I reckon. I should have been given a heads up. Sigh. Gary From: David Cole Sent: 15/09/2015 10:39 PM To: Jerry Moore Cc: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3 / K3S Station setup question Hi, Just making the point that as things are added, you will need more space... I once built a tight cabinet like that, and within a year, it was too small... -- Thanks and 73's, For equipment, and software setups and reviews see: www.nk7z.net For MixW support see; http://groups.yahoo.com/neo/groups/mixw/info For Dopplergram information see: http://groups.yahoo.com/neo/groups/dopplergram/info For MM-SSTV see: http://groups.yahoo.com/neo/groups/MM-SSTV/info On Mon, 2015-09-14 at 21:13 -0400, Jerry Moore wrote: > That will likely go on top when I get it eventually :) > > -Original Message- > From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of David > Cole > Sent: Monday, September 14, 2015 3:55 PM > To: elecraft@mailman.qth.net > Subject: Re: [Elecraft] K3 / K3S Station setup question > > What about the new Speaker? :) > -- > Thanks and 73's, > For equipment, and software setups and reviews see: > www.nk7z.net > > For MixW support see; > http://groups.yahoo.com/neo/groups/mixw/info > For Dopplergram information see: > http://groups.yahoo.com/neo/groups/dopplergram/info > For MM-SSTV see: > http://groups.yahoo.com/neo/groups/MM-SSTV/info > > > On Mon, 2015-09-14 at 15:28 -0400, ae...@carolinaheli.com wrote: > > It's been a while and I'm a huge proponent of measure twice cut once. > > I'm building a hutch for my operating desk. The desk is 4' wide x 28" deep > (2' > > 4"). I'm right handed and my primary mode will be CW. I have both a > > Bencher paddle and a generic straight key. I need about 18" wide for > > my K3S and future P3. The K3S is 10"x10"x7.25"(stand extended and air gap > above it. > > Planning to use a 1 x or 2 x 12 for the shelf and 1x for the vertical > > supports. > > > > Not sure on right to left arrangement with me sitting in the middle. > > Was thinking keys, then P3, then radio, then space to the left. > > Allowing 3/4" for the end support, 9 inches for the keys to store, > > 3/4" for a vertical support, then 18" or so for the P3, then K3S, the > > 3/4 for vertical Support. That brings me 29.25" from the Right edge > > leaving 18" (if we subtract 3/4" for the end vertical support) for the > > Eventual AMP. If I eventually get the External antenna tuner it will > > go on top of the shelf or on top of the amp directly if it will fit. > > > > Does this sound like a proper setup to operate CW with the arm on the > > desk..etc.. turn dials with the left hand..etc.. I'll have a > > laptop/monitors on top of the shelf and a smallish keyboard/mouse on the > desktop. > > > > Just trying to get it all worked out so I don't have to remake this > > thing several times.. why re-invent the wheel when someone has already > > done it right? > > > > Thanks in advance. > > Jerry Moore > > K3S SN# TBA Wednesday > > > > __ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:Elecraft@mailman.qth.net > > > > This list hosted by: http://www.qsl.net Please help support this email > > list: http://www.qsl.net/donate.html Message delivered to > > d...@nk7z.net > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this
Re: [Elecraft] K3 / K3S Station setup question
Sorry that you were not previously informed. For the record, Elecraft will be announcing something new in the future that will impact the space required for your station. The size may vary from one inch wide to 19 inches (rack mount), and will vary in height from one inch to 24 inches. Now you have been informed about the size of future Elecraft products. Make your desk plans suitable for that expansion.:-) 73, Don W3FPR On 9/15/2015 8:48 AM, Gary wrote: Humphi just completed a nice desk in the motor home. Why was I not informed that it needed to be wider to allow for a new external speaker? Pretty ordinary communication from Elecraft I reckon. I should have been given a heads up. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
Hi, Just making the point that as things are added, you will need more space... I once built a tight cabinet like that, and within a year, it was too small... -- Thanks and 73's, For equipment, and software setups and reviews see: www.nk7z.net For MixW support see; http://groups.yahoo.com/neo/groups/mixw/info For Dopplergram information see: http://groups.yahoo.com/neo/groups/dopplergram/info For MM-SSTV see: http://groups.yahoo.com/neo/groups/MM-SSTV/info On Mon, 2015-09-14 at 21:13 -0400, Jerry Moore wrote: > That will likely go on top when I get it eventually :) > > -Original Message- > From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of David > Cole > Sent: Monday, September 14, 2015 3:55 PM > To: elecraft@mailman.qth.net > Subject: Re: [Elecraft] K3 / K3S Station setup question > > What about the new Speaker? :) > -- > Thanks and 73's, > For equipment, and software setups and reviews see: > www.nk7z.net > > For MixW support see; > http://groups.yahoo.com/neo/groups/mixw/info > For Dopplergram information see: > http://groups.yahoo.com/neo/groups/dopplergram/info > For MM-SSTV see: > http://groups.yahoo.com/neo/groups/MM-SSTV/info > > > On Mon, 2015-09-14 at 15:28 -0400, ae...@carolinaheli.com wrote: > > It's been a while and I'm a huge proponent of measure twice cut once. > > I'm building a hutch for my operating desk. The desk is 4' wide x 28" deep > (2' > > 4"). I'm right handed and my primary mode will be CW. I have both a > > Bencher paddle and a generic straight key. I need about 18" wide for > > my K3S and future P3. The K3S is 10"x10"x7.25"(stand extended and air gap > above it. > > Planning to use a 1 x or 2 x 12 for the shelf and 1x for the vertical > > supports. > > > > Not sure on right to left arrangement with me sitting in the middle. > > Was thinking keys, then P3, then radio, then space to the left. > > Allowing 3/4" for the end support, 9 inches for the keys to store, > > 3/4" for a vertical support, then 18" or so for the P3, then K3S, the > > 3/4 for vertical Support. That brings me 29.25" from the Right edge > > leaving 18" (if we subtract 3/4" for the end vertical support) for the > > Eventual AMP. If I eventually get the External antenna tuner it will > > go on top of the shelf or on top of the amp directly if it will fit. > > > > Does this sound like a proper setup to operate CW with the arm on the > > desk..etc.. turn dials with the left hand..etc.. I'll have a > > laptop/monitors on top of the shelf and a smallish keyboard/mouse on the > desktop. > > > > Just trying to get it all worked out so I don't have to remake this > > thing several times.. why re-invent the wheel when someone has already > > done it right? > > > > Thanks in advance. > > Jerry Moore > > K3S SN# TBA Wednesday > > > > __ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:Elecraft@mailman.qth.net > > > > This list hosted by: http://www.qsl.net Please help support this email > > list: http://www.qsl.net/donate.html Message delivered to > > d...@nk7z.net > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html Message > delivered to je...@carolinaheli.com > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
You COULD just buy a larger motor home :D Jer From: Gary [mailto:vk1zzg...@gmail.com] Sent: Tuesday, September 15, 2015 8:49 AM To: d...@nk7z.net; Jerry Moore Cc: elecraft@mailman.qth.net Subject: RE: [Elecraft] K3 / K3S Station setup question Humphi just completed a nice desk in the motor home. Why was I not informed that it needed to be wider to allow for a new external speaker? Pretty ordinary communication from Elecraft I reckon. I should have been given a heads up. Sigh. Gary _ From: David Cole <mailto:d...@nk7z.net> Sent: 15/09/2015 10:39 PM To: Jerry Moore <mailto:je...@carolinaheli.com> Cc: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3 / K3S Station setup question Hi, Just making the point that as things are added, you will need more space... I once built a tight cabinet like that, and within a year, it was too small... -- Thanks and 73's, For equipment, and software setups and reviews see: www.nk7z.net For MixW support see; http://groups.yahoo.com/neo/groups/mixw/info For Dopplergram information see: http://groups.yahoo.com/neo/groups/dopplergram/info For MM-SSTV see: http://groups.yahoo.com/neo/groups/MM-SSTV/info On Mon, 2015-09-14 at 21:13 -0400, Jerry Moore wrote: > That will likely go on top when I get it eventually :) > > -Original Message- > From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of David > Cole > Sent: Monday, September 14, 2015 3:55 PM > To: elecraft@mailman.qth.net > Subject: Re: [Elecraft] K3 / K3S Station setup question > > What about the new Speaker? :) > -- > Thanks and 73's, > For equipment, and software setups and reviews see: > www.nk7z.net > > For MixW support see; > http://groups.yahoo.com/neo/groups/mixw/info > For Dopplergram information see: > http://groups.yahoo.com/neo/groups/dopplergram/info > For MM-SSTV see: > http://groups.yahoo.com/neo/groups/MM-SSTV/info > > > On Mon, 2015-09-14 at 15:28 -0400, ae...@carolinaheli.com wrote: > > It's been a while and I'm a huge proponent of measure twice cut once. > > I'm building a hutch for my operating desk. The desk is 4' wide x 28" deep > (2' > > 4"). I'm right handed and my primary mode will be CW. I have both a > > Bencher paddle and a generic straight key. I need about 18" wide for > > my K3S and future P3. The K3S is 10"x10"x7.25"(stand extended and air gap > above it. > > Planning to use a 1 x or 2 x 12 for the shelf and 1x for the vertical > > supports. > > > > Not sure on right to left arrangement with me sitting in the middle. > > Was thinking keys, then P3, then radio, then space to the left. > > Allowing 3/4" for the end support, 9 inches for the keys to store, > > 3/4" for a vertical support, then 18" or so for the P3, then K3S, the > > 3/4 for vertical Support. That brings me 29.25" from the Right edge > > leaving 18" (if we subtract 3/4" for the end vertical support) for the > > Eventual AMP. If I eventually get the External antenna tuner it will > > go on top of the shelf or on top of the amp directly if it will fit. > > > > Does this sound like a proper setup to operate CW with the arm on the > > desk..etc.. turn dials with the left hand..etc.. I'll have a > > laptop/monitors on top of the shelf and a smallish keyboard/mouse on the > desktop. > > > > Just trying to get it all worked out so I don't have to remake this > > thing several times.. why re-invent the wheel when someone has already > > done it right? > > > > Thanks in advance. > > Jerry Moore > > K3S SN# TBA Wednesday > > > > __ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:Elecraft@mailman.qth.net > > > > This list hosted by: http://www.qsl.net Please help support this email > > list: http://www.qsl.net/donate.html Message delivered to > > d...@nk7z.net > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html Message > delivered to je...@carolinaheli.com > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: htt
Re: [Elecraft] K3 / K3S Station setup question
Here's an idea to consider -- when I built mine I made the shelf out of 3/4" plywood with 1 x 4's attached to the front and back of the shelf. Screws and glue. This makes the actual thickness of the shelf about 3-1/2", but makes it strong enough that you don't need vertical supports except at the ends. Vertical supports always seem to be in the wrong places! Vic 4X6GP/K2VCO > On Sep 14, 2015, at 10:28 PM,> wrote: > > It's been a while and I'm a huge proponent of measure twice cut once. I'm > building a hutch for my operating desk. The desk is 4' wide x 28" deep (2' > 4"). I'm right handed and my primary mode will be CW. I have both a Bencher > paddle and a generic straight key. I need about 18" wide for my K3S and > future P3. The K3S is 10"x10"x7.25"(stand extended and air gap above it. > Planning to use a 1 x or 2 x 12 for the shelf and 1x for the vertical > supports. > > Not sure on right to left arrangement with me sitting in the middle. Was > thinking keys, then P3, then radio, then space to the left. > Allowing 3/4" for the end support, 9 inches for the keys to store, 3/4" for > a vertical support, then 18" or so for the P3, then K3S, the 3/4 for > vertical Support. That brings me 29.25" from the Right edge leaving 18" (if > we subtract 3/4" for the end vertical support) for the Eventual AMP. If I > eventually get the External antenna tuner it will go on top of the shelf or > on top of the amp directly if it will fit. > > Does this sound like a proper setup to operate CW with the arm on the > desk..etc.. turn dials with the left hand..etc.. I'll have a laptop/monitors > on top of the shelf and a smallish keyboard/mouse on the desktop. > > Just trying to get it all worked out so I don't have to remake this thing > several times.. why re-invent the wheel when someone has already done it > right? > > Thanks in advance. > Jerry Moore > K3S SN# TBA Wednesday > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to k2vco@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
That will likely go on top when I get it eventually :) -Original Message- From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of David Cole Sent: Monday, September 14, 2015 3:55 PM To: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3 / K3S Station setup question What about the new Speaker? :) -- Thanks and 73's, For equipment, and software setups and reviews see: www.nk7z.net For MixW support see; http://groups.yahoo.com/neo/groups/mixw/info For Dopplergram information see: http://groups.yahoo.com/neo/groups/dopplergram/info For MM-SSTV see: http://groups.yahoo.com/neo/groups/MM-SSTV/info On Mon, 2015-09-14 at 15:28 -0400, ae...@carolinaheli.com wrote: > It's been a while and I'm a huge proponent of measure twice cut once. > I'm building a hutch for my operating desk. The desk is 4' wide x 28" deep (2' > 4"). I'm right handed and my primary mode will be CW. I have both a > Bencher paddle and a generic straight key. I need about 18" wide for > my K3S and future P3. The K3S is 10"x10"x7.25"(stand extended and air gap above it. > Planning to use a 1 x or 2 x 12 for the shelf and 1x for the vertical > supports. > > Not sure on right to left arrangement with me sitting in the middle. > Was thinking keys, then P3, then radio, then space to the left. > Allowing 3/4" for the end support, 9 inches for the keys to store, > 3/4" for a vertical support, then 18" or so for the P3, then K3S, the > 3/4 for vertical Support. That brings me 29.25" from the Right edge > leaving 18" (if we subtract 3/4" for the end vertical support) for the > Eventual AMP. If I eventually get the External antenna tuner it will > go on top of the shelf or on top of the amp directly if it will fit. > > Does this sound like a proper setup to operate CW with the arm on the > desk..etc.. turn dials with the left hand..etc.. I'll have a > laptop/monitors on top of the shelf and a smallish keyboard/mouse on the desktop. > > Just trying to get it all worked out so I don't have to remake this > thing several times.. why re-invent the wheel when someone has already > done it right? > > Thanks in advance. > Jerry Moore > K3S SN# TBA Wednesday > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net Please help support this email > list: http://www.qsl.net/donate.html Message delivered to > d...@nk7z.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to je...@carolinaheli.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
Jerry, I’m also a righty and built part of my desk / operating setup. Mine is a little different, as I have a 27” iMac - sitting off to the left. But here’s what my setup is like: - A 54” wide, 24” deep double pedestal desk with a solid core 80” wide x 32” deep door sitting on top. This gives me a w-i-d-e operating surface. - The iMac sits off to the left. On top I build a double high “riser” out of 3/4” oak plywood, faced with oak strips.; the bottom riser is 4-1/2” high x 48” wide. Under it are my two Begali keys - a paddle and a straight key. Also gives me room to slide my wireless keyboard and track pad underneath when not in use. The upper riser is 5-1/2” high x 20” wide and sits on the left end of the lower riser, basically directly in front of me. Sitting on the second level (the top of the long riser) are, from left to right: K3, P3, KPA500, homebrew 144 MHz 80 watt amp, and an MFJ-4245MV power supply. My KAT500 tuner sits atop the KPA500. This arrangement puts the K3/P3 directly in front of me, and allows me to move the keys around on the desk under them as I want. On top of that third level, the upper riser, I have sitting an ASUS 23” second monitor, a KX3, and my Tascam external sound card. The upper surface of each riser is covered by black, non-stick, rubberized, “shelf paper” I got at a fabric store. Keeps stuff from sliding around. I like having the K3/P3 directly in front of me and the keys under them. I previously had this equipment in place without any risers and was not 100% happy with the layout or the ability to use the equipment easily. Jim / W6JHB > On Monday, Sep 14, 2015, at Monday, 12:28 PM, ae...@carolinaheli.com wrote: > > It's been a while and I'm a huge proponent of measure twice cut once. I'm > building a hutch for my operating desk. The desk is 4' wide x 28" deep (2' > 4"). I'm right handed and my primary mode will be CW. I have both a Bencher > paddle and a generic straight key. I need about 18" wide for my K3S and > future P3. The K3S is 10"x10"x7.25"(stand extended and air gap above it. > Planning to use a 1 x or 2 x 12 for the shelf and 1x for the vertical > supports. > > Not sure on right to left arrangement with me sitting in the middle. Was > thinking keys, then P3, then radio, then space to the left. > Allowing 3/4" for the end support, 9 inches for the keys to store, 3/4" for > a vertical support, then 18" or so for the P3, then K3S, the 3/4 for > vertical Support. That brings me 29.25" from the Right edge leaving 18" (if > we subtract 3/4" for the end vertical support) for the Eventual AMP. If I > eventually get the External antenna tuner it will go on top of the shelf or > on top of the amp directly if it will fit. > > Does this sound like a proper setup to operate CW with the arm on the > desk..etc.. turn dials with the left hand..etc.. I'll have a laptop/monitors > on top of the shelf and a smallish keyboard/mouse on the desktop. > > Just trying to get it all worked out so I don't have to remake this thing > several times.. why re-invent the wheel when someone has already done it > right? > > Thanks in advance. > Jerry Moore > K3S SN# TBA Wednesday > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to w6...@me.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
What about the new Speaker? :) -- Thanks and 73's, For equipment, and software setups and reviews see: www.nk7z.net For MixW support see; http://groups.yahoo.com/neo/groups/mixw/info For Dopplergram information see: http://groups.yahoo.com/neo/groups/dopplergram/info For MM-SSTV see: http://groups.yahoo.com/neo/groups/MM-SSTV/info On Mon, 2015-09-14 at 15:28 -0400, ae...@carolinaheli.com wrote: > It's been a while and I'm a huge proponent of measure twice cut once. I'm > building a hutch for my operating desk. The desk is 4' wide x 28" deep (2' > 4"). I'm right handed and my primary mode will be CW. I have both a Bencher > paddle and a generic straight key. I need about 18" wide for my K3S and > future P3. The K3S is 10"x10"x7.25"(stand extended and air gap above it. > Planning to use a 1 x or 2 x 12 for the shelf and 1x for the vertical > supports. > > Not sure on right to left arrangement with me sitting in the middle. Was > thinking keys, then P3, then radio, then space to the left. > Allowing 3/4" for the end support, 9 inches for the keys to store, 3/4" for > a vertical support, then 18" or so for the P3, then K3S, the 3/4 for > vertical Support. That brings me 29.25" from the Right edge leaving 18" (if > we subtract 3/4" for the end vertical support) for the Eventual AMP. If I > eventually get the External antenna tuner it will go on top of the shelf or > on top of the amp directly if it will fit. > > Does this sound like a proper setup to operate CW with the arm on the > desk..etc.. turn dials with the left hand..etc.. I'll have a laptop/monitors > on top of the shelf and a smallish keyboard/mouse on the desktop. > > Just trying to get it all worked out so I don't have to remake this thing > several times.. why re-invent the wheel when someone has already done it > right? > > Thanks in advance. > Jerry Moore > K3S SN# TBA Wednesday > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to d...@nk7z.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 / K3S Station setup question
Jer, Make the space for the K3S and P3 1.5 inches wider than the two units combined - you need some space to grip the sides of the radio and P3 after you have both inserted in the hutch. You will not need any more than 3/4 stock for the shelf and top of the hutch. If think you need extra support for the shelf, glue a 2 inch wide strip to the back edge of the shelf and top (under the shelf). That way you have maximum view in the front of the hutch. That will also keep the hutch from racking if you fit the ends tight. Since your hutch will not be close to the end of the desk, just build it and place it loose on the desk. That way you can move it from side to side to see what position is going to work best for you. Once you determine that position you can fasten it to the desktop if desired. 73, Don W3FPR On 9/14/2015 3:28 PM, ae...@carolinaheli.com wrote: It's been a while and I'm a huge proponent of measure twice cut once. I'm building a hutch for my operating desk. The desk is 4' wide x 28" deep (2' 4"). I'm right handed and my primary mode will be CW. I have both a Bencher paddle and a generic straight key. I need about 18" wide for my K3S and future P3. The K3S is 10"x10"x7.25"(stand extended and air gap above it. Planning to use a 1 x or 2 x 12 for the shelf and 1x for the vertical supports. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3 / K3S Station setup question
It's been a while and I'm a huge proponent of measure twice cut once. I'm building a hutch for my operating desk. The desk is 4' wide x 28" deep (2' 4"). I'm right handed and my primary mode will be CW. I have both a Bencher paddle and a generic straight key. I need about 18" wide for my K3S and future P3. The K3S is 10"x10"x7.25"(stand extended and air gap above it. Planning to use a 1 x or 2 x 12 for the shelf and 1x for the vertical supports. Not sure on right to left arrangement with me sitting in the middle. Was thinking keys, then P3, then radio, then space to the left. Allowing 3/4" for the end support, 9 inches for the keys to store, 3/4" for a vertical support, then 18" or so for the P3, then K3S, the 3/4 for vertical Support. That brings me 29.25" from the Right edge leaving 18" (if we subtract 3/4" for the end vertical support) for the Eventual AMP. If I eventually get the External antenna tuner it will go on top of the shelf or on top of the amp directly if it will fit. Does this sound like a proper setup to operate CW with the arm on the desk..etc.. turn dials with the left hand..etc.. I'll have a laptop/monitors on top of the shelf and a smallish keyboard/mouse on the desktop. Just trying to get it all worked out so I don't have to remake this thing several times.. why re-invent the wheel when someone has already done it right? Thanks in advance. Jerry Moore K3S SN# TBA Wednesday __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com