Re: [Elecraft] K3S - blank screen - won't start won't shut off

2021-10-15 Thread Ed via Elecraft
Our club's K3 has had a similar  problem for several months.  It only occurs 
when you physically turn the K3 power off from the from the front panel.  The 
display stays lit, but remains blank.  Pressing the power button has no effect 
until I turn off the 13.8V supply, and turning it back on.   When the K3 is 
turned on using the front panel button, the display works OK until the next 
time we turn off the power using the front panel.Our club K3 is set up as a 
remote station using the RemoteHams.com software.  The K3 powers on and off 
just fine when done from the remote client software.It seems like a 5V 
regulator problem would affect the display all the time, not just when the 
front panel power button is pressed.Thanks & 73,EdN2BHD


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

Re: [Elecraft] K3S - blank screen - won't start won't shut off

2021-10-14 Thread Jack Brindle via Elecraft
Keith _always_ gives good advice. I would add one thing. Make sure the AUXIO 
cable is disconnected from the back of the K3 when you do your testing. If it 
is directly connected to a KPA500 or KPA1500, it just may keep the K3 from 
shutting down. We don’t remember if the LCD will go blank in this situation, 
though.

This is why we specify AUXIO cables for the KPAs with pin 8 (the power-on pin) 
disconnected.

73,
Jack, W6FB

> On Oct 14, 2021, at 7:40 AM, Jim Sheldon  wrote:
> 
> Turned on my K3s this morning and got a blank screen.  Could not turn it off 
> after that without removing power.  Haven't opened it up yet, just wondering 
> if anyone has encountered this and can suggest a good place to start 
> troubleshooting before bothering Elecraft's Tech Support with it.
> 
> Jim Sheldon, W0EB
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to jackbrin...@me.com 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

Re: [Elecraft] K3S - blank screen - won't start won't shut off W0EB

2021-10-14 Thread Keith Trinity WE6R

Hi Jim;
First, do NOT try loading FW, don't do a Parameter-Reset (EE-INIT) when 
it is in this state.


1. Check the right side of the radio, it should be warm not hot.
If hot, then the 5 or 8 volt regulator is working too hard, either a 
short or itself is bad.


2. More likely, C102 on the FP (Front Panel) is shorting the 5Volts for 
the Contrast.

One end of C102 should have close to 5V.
You can reach this by just taking the top cover off!
It is on the rear side of the FP board at the top, directly behind the 
top left corner of the LCD.
It is our part# E530223.   10 uF,10V,20%,CERM,0805,SMD. Panasonic 
ECJ-2FF1A106Z.  Digikey PCC2233TR-ND.

Keith WE6R Elecraft K3/K4 Tech.



__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com 

[Elecraft] K3S - blank screen - won't start won't shut off

2021-10-14 Thread Jim Sheldon
Turned on my K3s this morning and got a blank screen.  Could not turn it 
off after that without removing power.  Haven't opened it up yet, just 
wondering if anyone has encountered this and can suggest a good place to 
start troubleshooting before bothering Elecraft's Tech Support with it.


Jim Sheldon, W0EB

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com