Re: [Elecraft] KPA has FAILED...high SWR reported by K3 when amp in Operate

2012-03-15 Thread ke9uw
Excellent response from service with an RF unit on the way...appeared not to
be switching into the transmit mode when in operate.

-
Chuck, KE9UW
--
View this message in context: 
http://elecraft.365791.n2.nabble.com/KPA-has-FAILED-high-SWR-reported-by-K3-when-amp-in-Operate-tp7371793p7377011.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html


[Elecraft] KPA has FAILED...high SWR reported by K3 when amp in Operate

2012-03-14 Thread ke9uw
My KPA500 causes a high SWR showing at the K3 when the amp is in transmit
operate. All else seems to work ok...reloaded firmware...checked
faults...something about power lost without controlled shutdown.

Any ideas? Pin diode?

-
Chuck, KE9UW
--
View this message in context: 
http://elecraft.365791.n2.nabble.com/KPA-has-FAILED-high-SWR-reported-by-K3-when-amp-in-Operate-tp7371793p7371793.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html


Re: [Elecraft] KPA has FAILED...high SWR reported by K3 when amp in Operate

2012-03-14 Thread hawley, charles j jr
Hi,
The amp has worked well with 500 watts out, and in standby works fine with 100 
watts and the power shown on the led meter is correct. When in operate, it 
shows high swr with only 1 or 2 watts of drive. So something in the t/r switch 
has failed.
I guess. 
Thanks for the reply.
Chuck, KE9UW

Sent from my iPad

On Mar 14, 2012, at 1:11 PM, mkoeh...@comcast.net mkoeh...@comcast.net 
wrote:

 Chuck - I'm a brand new KPA500 owner ...so don't have a lot of history. 
 Probably not this simple, but I would suggest looking closely at the 
 clearance between the center pin of the high power output connector and that 
 metal shield. I thought the design was exceptional but was disappointed at 
 how there was almost no clearance here. (If I had a Greenlee punch, I would 
 have taken a nibble out to provide more clearance!)  It's possible when you 
 kick into high power, it could arc/short or have a bad VSWR.  Also, have all 
 the cables on the output side been run 500W+ before??  73- Mark WA3OFR 
 Sent via BlackBerry by ATT
 
 -Original Message-
 From: ke9uw c-haw...@illinois.edu
 Date: Wed, 14 Mar 2012 06:37:06 
 To: elecraft@mailman.qth.net
 Subject: [Elecraft] KPA has FAILED...high SWR reported by K3 when amp in
Operate
 
 My KPA500 causes a high SWR showing at the K3 when the amp is in transmit
 operate. All else seems to work ok...reloaded firmware...checked
 faults...something about power lost without controlled shutdown.
 
 Any ideas? Pin diode?
 
 -
 Chuck, KE9UW
 --
 View this message in context: 
 http://elecraft.365791.n2.nabble.com/KPA-has-FAILED-high-SWR-reported-by-K3-when-amp-in-Operate-tp7371793p7371793.html
 Sent from the Elecraft mailing list archive at Nabble.com.
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net
 
 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html