Re: [Elecraft] KX3-MIC COMP Setting / Metering
Well, Mostly because Gary at Elecraft told me he monitors power output since the ALC meter isn't driving right and that is what he recommends. That is difficult in the field on batteries because the target power is variable based on voltage. Also, the meter defaults to ALC when adjusting mic gain making it hard to see power while adjusting since this can't be overriden. I'm also concerned about having a dirty, overmodulated signal, so I'm staying conservative. As near as I can tell, I may be okay with a setting as low as 10-12, and 1 on compression but others are saying they are driving with as much gain as 40+ and significanltly higher compression. This seems to be a pretty broad range for everyone with identical equipment to be properly adjusted (understanding minor differences may occur with different voice characteristics) I haven't had a chance to coordinate a contact with a local friend and I have difficulty listening to my own voice in a second receiver. -- View this message in context: http://elecraft.365791.n2.nabble.com/KX3-MIC-COMP-Setting-Metering-tp7562532p7562590.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] KX3-MIC COMP Setting / Metering
I use a small electret mike form an old computer. Mic gain of 6 causes ALC activity just below full scale. Reports indicated that COMP to the max (30) produced punchy and undistorted signal. When listening on K3, varying mic gain from 4 to 10 caused very little difference in speech quality. IM in KX3 strongly depends on the combination of power and voltage. See a document in file section on yahoo KX3 site. Too much power at low voltage can cause IMD of -20db. The effect of mic gain and compression on IMD is much lower than that of voltage. Confirmed on P3. KX3 seems to be very sensitive to low voltage as far as efficiency is concerned. For example, at 12V the radio draws 2.2A and produces 10W. About 38% efficiency and 16W dissipation. At 8V (NiMH under load), the radio produces 2.5W and draws 1.8A, for 17% efficiency and 12 W dissipation. Voltage and amp readings from KX3. Setting power to 5W at 12V, the radio draws 1.1A, for 38% efficiency and 8 W dissipation. Not all of it is bad as many other radios stop working 11V. Ignacy, NO9E -- View this message in context: http://elecraft.365791.n2.nabble.com/KX3-MIC-COMP-Setting-Metering-tp7562532p7562597.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] KX3-MIC COMP Setting / Metering
I'm curious what MIC GAIN and COMPRESSION settings everyone are using with the MH3 microphone. ALC metering is quite spotty after getting an initial peak and compression metering doesn't show much either. Gary tells my to just adjust for power out, but this is complicated when on battery, because power is folded back and the metering automatically switches back to ALC/CMP. I have made one SSB contact with a MIC setting of 12, and received favorable audio. Compression seems to kick on hard listening with the monitor, so a left the setting at only one. Hopefully, future firmware will fix the ALC/COMP metering to be smoother and more responsive like the K3. Jim -- View this message in context: http://elecraft.365791.n2.nabble.com/KX3-MIC-COMP-Setting-Metering-tp7562532.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] KX3-MIC COMP Setting / Metering
Jim, Rather than getting someone else's settings, why not adjust yours the way it should be Work into a dummy load or turn the power to zero - then First set compression to zero, then adjust the mic gain to produce 5 to 7 bars on the ALC meter. You mic gain may be 25 or higher, but the number of ALC bars is the most important factor. Then turn up compression to suit your operating desires - listen on the monitor until it sounds right. 73, Don W3FPR On 9/12/2012 10:50 AM, Jim - W6VAR wrote: I'm curious what MIC GAIN and COMPRESSION settings everyone are using with the MH3 microphone. ALC metering is quite spotty after getting an initial peak and compression metering doesn't show much either. Gary tells my to just adjust for power out, but this is complicated when on battery, because power is folded back and the metering automatically switches back to ALC/CMP. I have made one SSB contact with a MIC setting of 12, and received favorable audio. Compression seems to kick on hard listening with the monitor, so a left the setting at only one. Hopefully, future firmware will fix the ALC/COMP metering to be smoother and more responsive like the K3. Jim -- View this message in context: http://elecraft.365791.n2.nabble.com/KX3-MIC-COMP-Setting-Metering-tp7562532.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] KX3-MIC COMP Setting / Metering
Understood, but the metering isn't working right. Protocal described was from Gary at Elecraft. Sent from my iPhone On Sep 12, 2012, at 9:36 AM, Don Wilhelm w3...@embarqmail.com wrote: Jim, Rather than getting someone else's settings, why not adjust yours the way it should be Work into a dummy load or turn the power to zero - then First set compression to zero, then adjust the mic gain to produce 5 to 7 bars on the ALC meter. You mic gain may be 25 or higher, but the number of ALC bars is the most important factor. Then turn up compression to suit your operating desires - listen on the monitor until it sounds right. 73, Don W3FPR On 9/12/2012 10:50 AM, Jim - W6VAR wrote: I'm curious what MIC GAIN and COMPRESSION settings everyone are using with the MH3 microphone. ALC metering is quite spotty after getting an initial peak and compression metering doesn't show much either. Gary tells my to just adjust for power out, but this is complicated when on battery, because power is folded back and the metering automatically switches back to ALC/CMP. I have made one SSB contact with a MIC setting of 12, and received favorable audio. Compression seems to kick on hard listening with the monitor, so a left the setting at only one. Hopefully, future firmware will fix the ALC/COMP metering to be smoother and more responsive like the K3. Jim -- View this message in context: http://elecraft.365791.n2.nabble.com/KX3-MIC-COMP-Setting-Metering-tp7562532.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] KX3-MIC COMP Setting / Metering
Jim, OK, but I did not think there was a problem with the metering - the KX3 manual says to adjust for 5 bars, but the K3 says to go up to 7 bars, so the 5 to 7 bar comment was in error. I have 1.12 firmware in my KX1 Yes, it is difficult to drive the ALC above 5, but I suggest driving it up to 5 bars and then go just a bit higher - then bring up compression to your taste. My MH3 runs about 35 on the mic gain and 15 on compression. OTOH, I have a Yamaha CM500 running with an adapter to connect only the tip instead of the stock plug that connects the tip and ring together - that runs well with the mic gain set to 20 and compression to 15 - that is one hot microphone element. 73, Don W3FPR On 9/12/2012 1:00 PM, James Kohnke (W6VAR) wrote: Understood, but the metering isn't working right. Protocal described was from Gary at Elecraft. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] KX3-MIC COMP Setting / Metering
Well, maybe some KX3s react a bit differently. I, also, noticed the phenomenon Jim described. With the KX3, and either the MH3 or my Yamaha CM500 I couldn't seem to talk at a volume to get 5 bars ALC (or 4, or 3) by raising and lowing my voice volume level even with mic gain up near 40 (and comp set to 0). If I talked loud, I'd show 6 or 7 bars, if I decrease my voice volume a bit, I'd get no bars. As Jim described, this is very unlike my K3, where the ALC level (shown by number of bars) seems very linear, and tracks with my voice volume. With the KX3, it's more like an all or nothing meter reading. Perhaps there's some other setting not right. I still have the original firmware as shipped (serial 1130). At least on my KX3, adjusting the mic gain does not feel at all like doing the same thing on the K3 I might also note a few other factors: 1. I was able to turn the mic level way down after adjusting TX EQ bringing up the mid and high frequencies by 12db (and two lower frequency bands down by 10db). This made everything a bit better. 2. When listening to my voice with mon on, the voice volume/level DOES seem to be linear and follow the volume of my speech - it's only the ALC metering that appears not so linear. 3. Using the same CM 500 on my K3 and my KX3, with about the same TX EQ on both, people have commented the KX3 sounds like it has a lot more bass. This may not be related... Oscar, WB5GCX On Wed, Sep 12, 2012 at 11:36 AM, Don Wilhelm w3...@embarqmail.com wrote: Jim, Rather than getting someone else's settings, why not adjust yours the way it should be Work into a dummy load or turn the power to zero - then... __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
