Re: [Emc-users] disty game to fight .... warming ....

2017-05-22 Thread Pavel G. Kasyanenko 
On 22.05.2017 18:48, giorgio foga wrote:
> In Russia 157 suicides documented in 2 years.

Please proof.


--
Check out the vibrant tech community on one of the world's most
engaging tech sites, Slashdot.org! http://sdm.link/slashdot
___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users

Re: [Emc-users] Tool Length Offset?

2016-12-25 Thread Pavel G. Kasyanenko 
Hello!

If we are talking about the Axis I have the same problem. And even more. 
I'm going to rewrite it in the near future.

Best regards,
Pavel

23.12.2016 05:01, Jim Craig пишет:
> I was running a program last night on my milling machine. I was cutting
> air at the time and saw something that I did not like. I hit the stop
> button in gmoccapy and the program stopped but then the tool plunged
> downward in the z direction. I found this very odd. I took a look at the
> tool offset and it was saying 0.000 in. Once again very odd. I played
> around with it for a little bit and found that when I hit stop then the
> tool length offset would be removed. Then this caused the machine to
> plunge for some reason.
>
> Luckily it did no damage since I was far enough above the part to not
> cause a crash.
>
> I have tried to reproduce this same behavior in a sim configuration in
> 2.7.8 but I cannot 100%. If you change the G49 G43 option the tool will
> show as moving on the screen but it is moving instantly as the change is
> being made. No real plunge occurring, or is it? Was this a glitch in
> 2.7.4? If not what could cause this behavior?
>
> Thanks,
>
> Jim
>
>
> --
> Developer Access Program for Intel Xeon Phi Processors
> Access to Intel Xeon Phi processor-based developer platforms.
> With one year of Intel Parallel Studio XE.
> Training and support from Colfax.
> Order your platform today.http://sdm.link/intel
> ___
> Emc-users mailing list
> Emc-users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/emc-users
>

--
Developer Access Program for Intel Xeon Phi Processors
Access to Intel Xeon Phi processor-based developer platforms.
With one year of Intel Parallel Studio XE.
Training and support from Colfax.
Order your platform today.http://sdm.link/intel
___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users

[Emc-users] LinuxCNC and FHA-25C-xx-E250 with 2-wire encoder

2016-09-24 Thread Pavel G. Kasyanenko 
Hello!
Does anyone have any experience of successful connection of 2-wire 
rotary encoder in a reducer harmonic drive FHA-25C-xx-E250 to LinuxCNC?
The exact name of the model: FHA-25C-100-E250-BCW-SPK0284.

The manual says that I can only use one control unit, which indicated 
same modelunder "ADJ..." label.
Such models on sale I have not found. I want to use this gear unit under 
the direct control of LinuxCNC.

The manual states that the two-wire model of rotary encoder is a 
"nikon-a absolute encoder".
And "The Nikon A interface is a serial, half-duplex type that is 
electrically the same as RS-485".

What about the protocol? Is this a closed protocol, or Ican find 
information on it and connect it to LinuxCNC?

Best regards,
Pavel

--
___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users