RE: Ethernet card problem
Thanks very much for the quick reply. I would agree with that. The model is a Kingston KNE100TX and it says that the driver is a dc(4). Which Ethernet selection and I supposed to pick for that on Sysinstall? Is there a way to reconfigure it after installation. I apologize for the ignorance but I am very new to all this. I basically just went step-by-step through the FreeBSD manual on installation. There was no option that said dc(4). Thanks again, Thomas P. Connolly Senior Development Engineer Colorado Engineering Experiment Station Inc. Phone: (970) 897-2711 Fax: (970) 897-2710 Email: [EMAIL PROTECTED] -Original Message- From: D J Hawkey Jr [mailto:[EMAIL PROTECTED]] Sent: Monday, December 09, 2002 9:45 AM To: Thomas Connolly Subject: Re: Ethernet card problem On Dec 09, at 09:32 AM, Thomas Connolly wrote: Hi all, I just installed FreeBSD on an HP Vectra machine with a Kingston KNE 100 network card. The FreeBSD Handbook says it is supported. From sysinstall, I chose the NE1000, NE2000, 3C503, WD/SMC80xx Ethernet Adapters ed0 Option. When I went to configure the network device, ed0 did not show up in the list. Can anyone offer me some guidance here? Double-check the NIC's model. Variou Kingston NICs are listed as ed(4), dc(4), and aue(4) compatable. I'd say you picked the wrong one. Thank you, Thomas Connolly Dave -- __ __ \__ \D. J. HAWKEY JR. / __/ \/\ [EMAIL PROTECTED]/\/ http://www.visi.com/~hawkeyd/ To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
RE: Ethernet card problem
Thanks again for the help. Can you tell me how to set my interface up manually so that it will use DHCP for the ip and netmask, gateway, etc.? Thanks, Tom Connolly -Original Message- From: D J Hawkey Jr [mailto:[EMAIL PROTECTED]] Sent: Monday, December 09, 2002 10:25 AM To: Thomas Connolly Subject: Re: Ethernet card problem On Dec 09, at 10:07 AM, Thomas Connolly wrote: Thanks very much for the quick reply. I would agree with that. The model is a Kingston KNE100TX and it says that the driver is a dc(4). Which Ethernet selection and I supposed to pick for that on Sysinstall? dc0, I would imagine. Is there a way to reconfigure it after installation. Oh, yes. Go on through the installation. Afterward, edit /etc/rc.conf to reflect reality. You'll have lines like these to change: hostname=sheol.localdomain ifconfig_ed0=inet 192.168.16.2 netmask 255.255.255.0 What you'll change is the hostname (if need be), and ifconfig_ed0 to ifconfig_dc0. IIRC, that's all it takes. I apologize for the ignorance but I am very new to all this. I basically just went step-by-step through the FreeBSD manual on installation. There was no option that said dc(4). I don't remember how to specify the interface within sysinstall(8), but I'm sure you can (make sure you've resolved conflicting interrupts first). I usually set up the network manually, after sysinstall(8), just to stay in practice! Thanks again, Thomas P. Connolly Senior Development Engineer Colorado Engineering Experiment Station Inc. Phone: (970) 897-2711 Fax: (970) 897-2710 Email: [EMAIL PROTECTED] Need a telecommuting UNIX SysAdmin in Minnesota? Dave -- __ __ \__ \D. J. HAWKEY JR. / __/ \/\ [EMAIL PROTECTED]/\/ http://www.visi.com/~hawkeyd/ To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
Re: Ethernet card problem
isnt is /stand/sysinstall, post install config, network, pick yer interface, answer yes to the dhcp popup, thats it? BTW, if it asks you if you want to activate now, that typically will not get you the new parameters on the interface, youll need to either ifconfig it down and then up, or reboot as a quik dirty way. Bri - Original Message - From: Thomas Connolly [EMAIL PROTECTED] To: [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Sent: Monday, December 09, 2002 9:36 AM Subject: RE: Ethernet card problem Thanks again for the help. Can you tell me how to set my interface up manually so that it will use DHCP for the ip and netmask, gateway, etc.? Thanks, Tom Connolly -Original Message- From: D J Hawkey Jr [mailto:[EMAIL PROTECTED]] Sent: Monday, December 09, 2002 10:25 AM To: Thomas Connolly Subject: Re: Ethernet card problem On Dec 09, at 10:07 AM, Thomas Connolly wrote: Thanks very much for the quick reply. I would agree with that. The model is a Kingston KNE100TX and it says that the driver is a dc(4). Which Ethernet selection and I supposed to pick for that on Sysinstall? dc0, I would imagine. Is there a way to reconfigure it after installation. Oh, yes. Go on through the installation. Afterward, edit /etc/rc.conf to reflect reality. You'll have lines like these to change: hostname=sheol.localdomain ifconfig_ed0=inet 192.168.16.2 netmask 255.255.255.0 What you'll change is the hostname (if need be), and ifconfig_ed0 to ifconfig_dc0. IIRC, that's all it takes. I apologize for the ignorance but I am very new to all this. I basically just went step-by-step through the FreeBSD manual on installation. There was no option that said dc(4). I don't remember how to specify the interface within sysinstall(8), but I'm sure you can (make sure you've resolved conflicting interrupts first). I usually set up the network manually, after sysinstall(8), just to stay in practice! Thanks again, Thomas P. Connolly Senior Development Engineer Colorado Engineering Experiment Station Inc. Phone: (970) 897-2711 Fax: (970) 897-2710 Email: [EMAIL PROTECTED] Need a telecommuting UNIX SysAdmin in Minnesota? Dave -- __ __ \__ \D. J. HAWKEY JR. / __/ \/\ [EMAIL PROTECTED]/\/ http://www.visi.com/~hawkeyd/ To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
RE: Ethernet card problem
Yes, that is what I tried to do but my interface doesn't come up in the list, only plip, and com 1 come up, not dc0. Thanks, Thomas Connolly -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of Brian Sent: Monday, December 09, 2002 10:45 AM To: Thomas Connolly; [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Subject: Re: Ethernet card problem isnt is /stand/sysinstall, post install config, network, pick yer interface, answer yes to the dhcp popup, thats it? BTW, if it asks you if you want to activate now, that typically will not get you the new parameters on the interface, youll need to either ifconfig it down and then up, or reboot as a quik dirty way. Bri - Original Message - From: Thomas Connolly [EMAIL PROTECTED] To: [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Sent: Monday, December 09, 2002 9:36 AM Subject: RE: Ethernet card problem Thanks again for the help. Can you tell me how to set my interface up manually so that it will use DHCP for the ip and netmask, gateway, etc.? Thanks, Tom Connolly -Original Message- From: D J Hawkey Jr [mailto:[EMAIL PROTECTED]] Sent: Monday, December 09, 2002 10:25 AM To: Thomas Connolly Subject: Re: Ethernet card problem On Dec 09, at 10:07 AM, Thomas Connolly wrote: Thanks very much for the quick reply. I would agree with that. The model is a Kingston KNE100TX and it says that the driver is a dc(4). Which Ethernet selection and I supposed to pick for that on Sysinstall? dc0, I would imagine. Is there a way to reconfigure it after installation. Oh, yes. Go on through the installation. Afterward, edit /etc/rc.conf to reflect reality. You'll have lines like these to change: hostname=sheol.localdomain ifconfig_ed0=inet 192.168.16.2 netmask 255.255.255.0 What you'll change is the hostname (if need be), and ifconfig_ed0 to ifconfig_dc0. IIRC, that's all it takes. I apologize for the ignorance but I am very new to all this. I basically just went step-by-step through the FreeBSD manual on installation. There was no option that said dc(4). I don't remember how to specify the interface within sysinstall(8), but I'm sure you can (make sure you've resolved conflicting interrupts first). I usually set up the network manually, after sysinstall(8), just to stay in practice! Thanks again, Thomas P. Connolly Senior Development Engineer Colorado Engineering Experiment Station Inc. Phone: (970) 897-2711 Fax: (970) 897-2710 Email: [EMAIL PROTECTED] Need a telecommuting UNIX SysAdmin in Minnesota? Dave -- __ __ \__ \D. J. HAWKEY JR. / __/ \/\ [EMAIL PROTECTED]/\/ http://www.visi.com/~hawkeyd/ To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
Re: Ethernet card problem
dc driver uses the miibus code, make sure you have that enabled on your kernel. There is nothing needed in sysinstall, a device probe ought to catch it IF the miibus is enabled in your kernel config. Sorry, I'm late on this discussion, if I've missed important points, please forgiveI just hadn't seen this point mentioned. Kevin Kinsey DaleCo, S.P. - Original Message - From: Thomas Connolly [EMAIL PROTECTED] To: 'Brian' [EMAIL PROTECTED]; [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Sent: Monday, December 09, 2002 11:50 AM Subject: RE: Ethernet card problem Yes, that is what I tried to do but my interface doesn't come up in the list, only plip, and com 1 come up, not dc0. Thanks, Thomas Connolly -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of Brian Sent: Monday, December 09, 2002 10:45 AM To: Thomas Connolly; [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Subject: Re: Ethernet card problem isnt is /stand/sysinstall, post install config, network, pick yer interface, answer yes to the dhcp popup, thats it? BTW, if it asks you if you want to activate now, that typically will not get you the new parameters on the interface, youll need to either ifconfig it down and then up, or reboot as a quik dirty way. Bri - Original Message - From: Thomas Connolly [EMAIL PROTECTED] To: [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Sent: Monday, December 09, 2002 9:36 AM Subject: RE: Ethernet card problem Thanks again for the help. Can you tell me how to set my interface up manually so that it will use DHCP for the ip and netmask, gateway, etc.? Thanks, Tom Connolly -Original Message- From: D J Hawkey Jr [mailto:[EMAIL PROTECTED]] Sent: Monday, December 09, 2002 10:25 AM To: Thomas Connolly Subject: Re: Ethernet card problem On Dec 09, at 10:07 AM, Thomas Connolly wrote: Thanks very much for the quick reply. I would agree with that. The model is a Kingston KNE100TX and it says that the driver is a dc(4). Which Ethernet selection and I supposed to pick for that on Sysinstall? dc0, I would imagine. Is there a way to reconfigure it after installation. Oh, yes. Go on through the installation. Afterward, edit /etc/rc.conf to reflect reality. You'll have lines like these to change: hostname=sheol.localdomain ifconfig_ed0=inet 192.168.16.2 netmask 255.255.255.0 What you'll change is the hostname (if need be), and ifconfig_ed0 to ifconfig_dc0. IIRC, that's all it takes. I apologize for the ignorance but I am very new to all this. I basically just went step-by-step through the FreeBSD manual on installation. There was no option that said dc(4). I don't remember how to specify the interface within sysinstall(8), but I'm sure you can (make sure you've resolved conflicting interrupts first). I usually set up the network manually, after sysinstall(8), just to stay in practice! Thanks again, Thomas P. Connolly Senior Development Engineer Colorado Engineering Experiment Station Inc. Phone: (970) 897-2711 Fax: (970) 897-2710 Email: [EMAIL PROTECTED] Need a telecommuting UNIX SysAdmin in Minnesota? Dave -- __ __ \__ \D. J. HAWKEY JR. / __/ \/\ [EMAIL PROTECTED] /\/ http://www.visi.com/~hawkeyd/ To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
RE: Ethernet card problem
Thanks for the advice but again, I am very new to all this. Can you tell me how to check if miibus is enabled and how to enable it if it is not? Thanks in advance, Tom Connolly -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of Kevin D. Kinsey, DaleCo, S.P. Sent: Monday, December 09, 2002 2:07 PM To: Thomas Connolly; 'Brian'; [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Subject: Re: Ethernet card problem dc driver uses the miibus code, make sure you have that enabled on your kernel. There is nothing needed in sysinstall, a device probe ought to catch it IF the miibus is enabled in your kernel config. Sorry, I'm late on this discussion, if I've missed important points, please forgiveI just hadn't seen this point mentioned. Kevin Kinsey DaleCo, S.P. - Original Message - From: Thomas Connolly [EMAIL PROTECTED] To: 'Brian' [EMAIL PROTECTED]; [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Sent: Monday, December 09, 2002 11:50 AM Subject: RE: Ethernet card problem Yes, that is what I tried to do but my interface doesn't come up in the list, only plip, and com 1 come up, not dc0. Thanks, Thomas Connolly -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of Brian Sent: Monday, December 09, 2002 10:45 AM To: Thomas Connolly; [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Subject: Re: Ethernet card problem isnt is /stand/sysinstall, post install config, network, pick yer interface, answer yes to the dhcp popup, thats it? BTW, if it asks you if you want to activate now, that typically will not get you the new parameters on the interface, youll need to either ifconfig it down and then up, or reboot as a quik dirty way. Bri - Original Message - From: Thomas Connolly [EMAIL PROTECTED] To: [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Sent: Monday, December 09, 2002 9:36 AM Subject: RE: Ethernet card problem Thanks again for the help. Can you tell me how to set my interface up manually so that it will use DHCP for the ip and netmask, gateway, etc.? Thanks, Tom Connolly -Original Message- From: D J Hawkey Jr [mailto:[EMAIL PROTECTED]] Sent: Monday, December 09, 2002 10:25 AM To: Thomas Connolly Subject: Re: Ethernet card problem On Dec 09, at 10:07 AM, Thomas Connolly wrote: Thanks very much for the quick reply. I would agree with that. The model is a Kingston KNE100TX and it says that the driver is a dc(4). Which Ethernet selection and I supposed to pick for that on Sysinstall? dc0, I would imagine. Is there a way to reconfigure it after installation. Oh, yes. Go on through the installation. Afterward, edit /etc/rc.conf to reflect reality. You'll have lines like these to change: hostname=sheol.localdomain ifconfig_ed0=inet 192.168.16.2 netmask 255.255.255.0 What you'll change is the hostname (if need be), and ifconfig_ed0 to ifconfig_dc0. IIRC, that's all it takes. I apologize for the ignorance but I am very new to all this. I basically just went step-by-step through the FreeBSD manual on installation. There was no option that said dc(4). I don't remember how to specify the interface within sysinstall(8), but I'm sure you can (make sure you've resolved conflicting interrupts first). I usually set up the network manually, after sysinstall(8), just to stay in practice! Thanks again, Thomas P. Connolly Senior Development Engineer Colorado Engineering Experiment Station Inc. Phone: (970) 897-2711 Fax: (970) 897-2710 Email: [EMAIL PROTECTED] Need a telecommuting UNIX SysAdmin in Minnesota? Dave -- __ __ \__ \D. J. HAWKEY JR. / __/ \/\ [EMAIL PROTECTED] /\/ http://www.visi.com/~hawkeyd/ To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
RE: Ethernet card problem
Oh yes, and one other thing, can you tell me how to do a device probe? Thanks again, Tom Connolly -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of Kevin D. Kinsey, DaleCo, S.P. Sent: Monday, December 09, 2002 2:07 PM To: Thomas Connolly; 'Brian'; [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Subject: Re: Ethernet card problem dc driver uses the miibus code, make sure you have that enabled on your kernel. There is nothing needed in sysinstall, a device probe ought to catch it IF the miibus is enabled in your kernel config. Sorry, I'm late on this discussion, if I've missed important points, please forgiveI just hadn't seen this point mentioned. Kevin Kinsey DaleCo, S.P. - Original Message - From: Thomas Connolly [EMAIL PROTECTED] To: 'Brian' [EMAIL PROTECTED]; [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Sent: Monday, December 09, 2002 11:50 AM Subject: RE: Ethernet card problem Yes, that is what I tried to do but my interface doesn't come up in the list, only plip, and com 1 come up, not dc0. Thanks, Thomas Connolly -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of Brian Sent: Monday, December 09, 2002 10:45 AM To: Thomas Connolly; [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Subject: Re: Ethernet card problem isnt is /stand/sysinstall, post install config, network, pick yer interface, answer yes to the dhcp popup, thats it? BTW, if it asks you if you want to activate now, that typically will not get you the new parameters on the interface, youll need to either ifconfig it down and then up, or reboot as a quik dirty way. Bri - Original Message - From: Thomas Connolly [EMAIL PROTECTED] To: [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Sent: Monday, December 09, 2002 9:36 AM Subject: RE: Ethernet card problem Thanks again for the help. Can you tell me how to set my interface up manually so that it will use DHCP for the ip and netmask, gateway, etc.? Thanks, Tom Connolly -Original Message- From: D J Hawkey Jr [mailto:[EMAIL PROTECTED]] Sent: Monday, December 09, 2002 10:25 AM To: Thomas Connolly Subject: Re: Ethernet card problem On Dec 09, at 10:07 AM, Thomas Connolly wrote: Thanks very much for the quick reply. I would agree with that. The model is a Kingston KNE100TX and it says that the driver is a dc(4). Which Ethernet selection and I supposed to pick for that on Sysinstall? dc0, I would imagine. Is there a way to reconfigure it after installation. Oh, yes. Go on through the installation. Afterward, edit /etc/rc.conf to reflect reality. You'll have lines like these to change: hostname=sheol.localdomain ifconfig_ed0=inet 192.168.16.2 netmask 255.255.255.0 What you'll change is the hostname (if need be), and ifconfig_ed0 to ifconfig_dc0. IIRC, that's all it takes. I apologize for the ignorance but I am very new to all this. I basically just went step-by-step through the FreeBSD manual on installation. There was no option that said dc(4). I don't remember how to specify the interface within sysinstall(8), but I'm sure you can (make sure you've resolved conflicting interrupts first). I usually set up the network manually, after sysinstall(8), just to stay in practice! Thanks again, Thomas P. Connolly Senior Development Engineer Colorado Engineering Experiment Station Inc. Phone: (970) 897-2711 Fax: (970) 897-2710 Email: [EMAIL PROTECTED] Need a telecommuting UNIX SysAdmin in Minnesota? Dave -- __ __ \__ \D. J. HAWKEY JR. / __/ \/\ [EMAIL PROTECTED] /\/ http://www.visi.com/~hawkeyd/ To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
Re: Ethernet card problem
On Dec 09, at 03:07 PM, Kevin D. Kinsey, DaleCo, S.P. wrote: dc driver uses the miibus code, make sure you have that enabled on your kernel. There is nothing needed in sysinstall, a device probe ought to catch it IF the miibus is enabled in your kernel config. Um, he can't enable miibus in the kernel from sysinstall(8), can he? I don't know that miibus is in the distribution kernel or not, if /modules/miibus.ko is likewise available, nor if you can activate modules from sysinstall(8). I don't recall any difficulties with sysinstall(8) when I brought up this box with Linksys NICs (Realtek chipsets, which also use dc(1)). Otherwise, you point out that which I'd forgotten. Thanks. Sorry, I'm late on this discussion, if I've missed important points, please forgiveI just hadn't seen this point mentioned. Forgive? Nonsense. You made the effort, that's what counts. Kevin Kinsey DaleCo, S.P. Dave -- __ __ \__ \D. J. HAWKEY JR. / __/ \/\ [EMAIL PROTECTED]/\/ http://www.visi.com/~hawkeyd/ To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
RE: Ethernet card problem
At 02:19 PM 12.9.2002 -0700, Thomas Connolly wrote: Thanks for the advice but again, I am very new to all this. Can you tell me how to check if miibus is enabled and how to enable it if it is not? Thanks in advance, Tom Connolly Just edit your kernel config file with this line and recompile: device miibus # MII bus support Best regards, Jack L. Stone, Administrator SageOne Net http://www.sage-one.net [EMAIL PROTECTED] To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
Re: Ethernet card problem
On Dec 09, at 03:51 PM, Jack L. Stone wrote: At 02:19 PM 12.9.2002 -0700, Thomas Connolly wrote: Thanks for the advice but again, I am very new to all this. Can you tell me how to check if miibus is enabled and how to enable it if it is not? Thanks in advance, Tom Connolly Just edit your kernel config file with this line and recompile: device miibus # MII bus support Again, this can only occur _after_ the initial sysinstall(8), right? Best regards, Jack L. Stone, Dave -- __ __ \__ \D. J. HAWKEY JR. / __/ \/\ [EMAIL PROTECTED]/\/ http://www.visi.com/~hawkeyd/ To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
Re: Ethernet card problem
- Original Message - From: D J Hawkey Jr [EMAIL PROTECTED] To: Jack L. Stone [EMAIL PROTECTED] Cc: Thomas Connolly [EMAIL PROTECTED]; Kevin D. Kinsey, DaleCo, S.P. [EMAIL PROTECTED]; 'Brian' [EMAIL PROTECTED]; [EMAIL PROTECTED] Sent: Monday, December 09, 2002 3:57 PM Subject: Re: Ethernet card problem On Dec 09, at 03:51 PM, Jack L. Stone wrote: At 02:19 PM 12.9.2002 -0700, Thomas Connolly wrote: Thanks for the advice but again, I am very new to all this. Can you tell me how to check if miibus is enabled and how to enable it if it is not? Thanks in advance, Tom Connolly Just edit your kernel config file with this line and recompile: device miibus # MII bus support Again, this can only occur _after_ the initial sysinstall(8), right? Best regards, Jack L. Stone, Dave Guess so. So, he's trying to do an FTP install, and it won't recognize his NIC? KDK To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
Re: Ethernet card problem
OK, he's got a Kingston (generally dc driver) and is trying to do sysinstall and d-load over NIC. IME it doesn't matter what you pick in the configuration section of sysinstall --- whatever's first should work, because those are just old nonPNP ISA NIC drivers. After doing kernel configuration in full-screen visual/CLI/skip then sysinstall does an initial device probe, and when you get to configure interface, it should be there. For the record, device miibus is enabled in -GENERIC kernel. If his NIC is *not* there when it's time to configure and start the d-load, it's a hardware/BIOS issue, or somebody's broke sysinstall(8).or is there another option I'm missing? Kevin Kinsey To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
RE: Ethernet card problem
I actually installed from CD and won't recognize my NIC. I selected the ed0 NIC from sysinstall because I wasn't sure what I was supposed to use for my card (Kingston KNE100TX - dc(4)). When I got to the configuration screen, there was no Ethernet card listed. I am confused on what to do next. What I'm haring is that I have to install miibus, then I have to edit /etc/rc.conf. Do I have that right? Thanks again, Thomas Connolly -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of Kevin D. Kinsey, DaleCo, S.P. Sent: Monday, December 09, 2002 2:58 PM To: [EMAIL PROTECTED]; Jack L. Stone Cc: Thomas Connolly; 'Brian'; [EMAIL PROTECTED] Subject: Re: Ethernet card problem - Original Message - From: D J Hawkey Jr [EMAIL PROTECTED] To: Jack L. Stone [EMAIL PROTECTED] Cc: Thomas Connolly [EMAIL PROTECTED]; Kevin D. Kinsey, DaleCo, S.P. [EMAIL PROTECTED]; 'Brian' [EMAIL PROTECTED]; [EMAIL PROTECTED] Sent: Monday, December 09, 2002 3:57 PM Subject: Re: Ethernet card problem On Dec 09, at 03:51 PM, Jack L. Stone wrote: At 02:19 PM 12.9.2002 -0700, Thomas Connolly wrote: Thanks for the advice but again, I am very new to all this. Can you tell me how to check if miibus is enabled and how to enable it if it is not? Thanks in advance, Tom Connolly Just edit your kernel config file with this line and recompile: device miibus # MII bus support Again, this can only occur _after_ the initial sysinstall(8), right? Best regards, Jack L. Stone, Dave Guess so. So, he's trying to do an FTP install, and it won't recognize his NIC? KDK To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
RE: Ethernet card problem
This is exactly my situation, any ideas?? If his NIC is *not* there when it's time to configure and start the d-load, it's a hardware/BIOS issue, or somebody's broke sysinstall(8).or is there another option I'm missing? Tom -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of Kevin D. Kinsey, DaleCo, S.P. Sent: Monday, December 09, 2002 3:05 PM To: [EMAIL PROTECTED]; Jack L. Stone Cc: [EMAIL PROTECTED] Subject: Re: Ethernet card problem OK, he's got a Kingston (generally dc driver) and is trying to do sysinstall and d-load over NIC. IME it doesn't matter what you pick in the configuration section of sysinstall --- whatever's first should work, because those are just old nonPNP ISA NIC drivers. After doing kernel configuration in full-screen visual/CLI/skip then sysinstall does an initial device probe, and when you get to configure interface, it should be there. For the record, device miibus is enabled in -GENERIC kernel. If his NIC is *not* there when it's time to configure and start the d-load, it's a hardware/BIOS issue, or somebody's broke sysinstall(8).or is there another option I'm missing? Kevin Kinsey To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
Re: Ethernet card problem
From: Thomas Connolly [EMAIL PROTECTED] Sent: Monday, December 09, 2002 4:15 PM Subject: RE: Ethernet card problem I actually installed from CD and won't recognize my NIC. I selected the ed0 NIC from sysinstall because I wasn't sure what I was supposed to use for my card (Kingston KNE100TX - dc(4)). When I got to the configuration screen, there was no Ethernet card listed. I am confused on what to do next. What I'm haring is that I have to install miibus, then I have to edit /etc/rc.conf. Do I have that right? Thanks again, Thomas Connolly If you're using the GENERIC kernel, miibus should already be enabled. As to rc.conf, see below. If you installed from CD, and therefore have a working system, please post the output of: $dmesg If you're able, pipe it to a .txt file and attach it, otherwise copy/paste to your email program. $dmesg attach.txt That might show us if there is a problem at device probe time. It would be worth your time to look at /etc/rc.conf, because it might be easy to spot if sysinstall actually wrote the file using ed0 instead of dc0. If so, changing it would be a hurdle on our way to fixing the issue. You could also send us output from ifconfig -a, but it sounds as if that's already been decided, and dc0 isn't in there. KDK To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
RE: Ethernet card problem
ah so then its not being detected, pci or isa card? Id isa, perhaps setting bios irq to isa legacy is necessary.. Bri On Mon, 9 Dec 2002, Thomas Connolly wrote: Yes, that is what I tried to do but my interface doesn't come up in the list, only plip, and com 1 come up, not dc0. Thanks, Thomas Connolly -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of Brian Sent: Monday, December 09, 2002 10:45 AM To: Thomas Connolly; [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Subject: Re: Ethernet card problem isnt is /stand/sysinstall, post install config, network, pick yer interface, answer yes to the dhcp popup, thats it? BTW, if it asks you if you want to activate now, that typically will not get you the new parameters on the interface, youll need to either ifconfig it down and then up, or reboot as a quik dirty way. Bri - Original Message - From: Thomas Connolly [EMAIL PROTECTED] To: [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Sent: Monday, December 09, 2002 9:36 AM Subject: RE: Ethernet card problem Thanks again for the help. Can you tell me how to set my interface up manually so that it will use DHCP for the ip and netmask, gateway, etc.? Thanks, Tom Connolly -Original Message- From: D J Hawkey Jr [mailto:[EMAIL PROTECTED]] Sent: Monday, December 09, 2002 10:25 AM To: Thomas Connolly Subject: Re: Ethernet card problem On Dec 09, at 10:07 AM, Thomas Connolly wrote: Thanks very much for the quick reply. I would agree with that. The model is a Kingston KNE100TX and it says that the driver is a dc(4). Which Ethernet selection and I supposed to pick for that on Sysinstall? dc0, I would imagine. Is there a way to reconfigure it after installation. Oh, yes. Go on through the installation. Afterward, edit /etc/rc.conf to reflect reality. You'll have lines like these to change: hostname=sheol.localdomain ifconfig_ed0=inet 192.168.16.2 netmask 255.255.255.0 What you'll change is the hostname (if need be), and ifconfig_ed0 to ifconfig_dc0. IIRC, that's all it takes. I apologize for the ignorance but I am very new to all this. I basically just went step-by-step through the FreeBSD manual on installation. There was no option that said dc(4). I don't remember how to specify the interface within sysinstall(8), but I'm sure you can (make sure you've resolved conflicting interrupts first). I usually set up the network manually, after sysinstall(8), just to stay in practice! Thanks again, Thomas P. Connolly Senior Development Engineer Colorado Engineering Experiment Station Inc. Phone: (970) 897-2711 Fax: (970) 897-2710 Email: [EMAIL PROTECTED] Need a telecommuting UNIX SysAdmin in Minnesota? Dave -- __ __ \__ \D. J. HAWKEY JR. / __/ \/\ [EMAIL PROTECTED]/\/ http://www.visi.com/~hawkeyd/ To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
RE: Ethernet card problem
It's a pci card. Thomas P. Connolly Senior Development Engineer Colorado Engineering Experiment Station Inc. Phone: (970) 897-2711 Fax: (970) 897-2710 Email: [EMAIL PROTECTED] -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of Brian Sent: Monday, December 09, 2002 4:27 PM To: Thomas Connolly Cc: [EMAIL PROTECTED]; [EMAIL PROTECTED] Subject: RE: Ethernet card problem ah so then its not being detected, pci or isa card? Id isa, perhaps setting bios irq to isa legacy is necessary.. Bri On Mon, 9 Dec 2002, Thomas Connolly wrote: Yes, that is what I tried to do but my interface doesn't come up in the list, only plip, and com 1 come up, not dc0. Thanks, Thomas Connolly -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of Brian Sent: Monday, December 09, 2002 10:45 AM To: Thomas Connolly; [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Subject: Re: Ethernet card problem isnt is /stand/sysinstall, post install config, network, pick yer interface, answer yes to the dhcp popup, thats it? BTW, if it asks you if you want to activate now, that typically will not get you the new parameters on the interface, youll need to either ifconfig it down and then up, or reboot as a quik dirty way. Bri - Original Message - From: Thomas Connolly [EMAIL PROTECTED] To: [EMAIL PROTECTED] Cc: [EMAIL PROTECTED] Sent: Monday, December 09, 2002 9:36 AM Subject: RE: Ethernet card problem Thanks again for the help. Can you tell me how to set my interface up manually so that it will use DHCP for the ip and netmask, gateway, etc.? Thanks, Tom Connolly -Original Message- From: D J Hawkey Jr [mailto:[EMAIL PROTECTED]] Sent: Monday, December 09, 2002 10:25 AM To: Thomas Connolly Subject: Re: Ethernet card problem On Dec 09, at 10:07 AM, Thomas Connolly wrote: Thanks very much for the quick reply. I would agree with that. The model is a Kingston KNE100TX and it says that the driver is a dc(4). Which Ethernet selection and I supposed to pick for that on Sysinstall? dc0, I would imagine. Is there a way to reconfigure it after installation. Oh, yes. Go on through the installation. Afterward, edit /etc/rc.conf to reflect reality. You'll have lines like these to change: hostname=sheol.localdomain ifconfig_ed0=inet 192.168.16.2 netmask 255.255.255.0 What you'll change is the hostname (if need be), and ifconfig_ed0 to ifconfig_dc0. IIRC, that's all it takes. I apologize for the ignorance but I am very new to all this. I basically just went step-by-step through the FreeBSD manual on installation. There was no option that said dc(4). I don't remember how to specify the interface within sysinstall(8), but I'm sure you can (make sure you've resolved conflicting interrupts first). I usually set up the network manually, after sysinstall(8), just to stay in practice! Thanks again, Thomas P. Connolly Senior Development Engineer Colorado Engineering Experiment Station Inc. Phone: (970) 897-2711 Fax: (970) 897-2710 Email: [EMAIL PROTECTED] Need a telecommuting UNIX SysAdmin in Minnesota? Dave -- __ __ \__ \D. J. HAWKEY JR. / __/ \/\ [EMAIL PROTECTED]/\/ http://www.visi.com/~hawkeyd/ To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
Re: Ethernet card problem
On Mon, Dec 09, 2002 at 04:30:28PM -0700, Thomas Connolly wrote: It's a pci card. mega-snip - miibus is in the generic, there are a dozen or so PCI cards that need it, some very common ones at that. - the dc driver works on one of my systems that needs it, both under 4.7-Stable and Current. - If you have a PCI card you can delete/ignore all the cards mentioned in sysinstall, they are all ISA cards. Nobody has suggested a few simple things yet. Such as is the card properly seated in it's slot, have you tried another PCI slot in the computer. Check the PCI settings in your BIOS for any reserved slots, turn off plug and play. Or maybe the card is kapot ? Good luck. -- Regards Cliff Sarginson The Netherlands [ This mail has been checked as virus-free ] To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
RE: Ethernet card problem
Make sure pnp operating system is disabled in your bios and pnp disabled on your card, or maybe recompiling your kernel for pnp support... --mat On Mon, 2002-12-09 at 16:28, Thomas Connolly wrote: This is exactly my situation, any ideas?? If his NIC is *not* there when it's time to configure and start the d-load, it's a hardware/BIOS issue, or somebody's broke sysinstall(8).or is there another option I'm missing? Tom -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of Kevin D. Kinsey, DaleCo, S.P. Sent: Monday, December 09, 2002 3:05 PM To: [EMAIL PROTECTED]; Jack L. Stone Cc: [EMAIL PROTECTED] Subject: Re: Ethernet card problem OK, he's got a Kingston (generally dc driver) and is trying to do sysinstall and d-load over NIC. IME it doesn't matter what you pick in the configuration section of sysinstall --- whatever's first should work, because those are just old nonPNP ISA NIC drivers. After doing kernel configuration in full-screen visual/CLI/skip then sysinstall does an initial device probe, and when you get to configure interface, it should be there. For the record, device miibus is enabled in -GENERIC kernel. If his NIC is *not* there when it's time to configure and start the d-load, it's a hardware/BIOS issue, or somebody's broke sysinstall(8).or is there another option I'm missing? Kevin Kinsey To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
Re: Ethernet card problem
Try setting the BIOS to OS TYPE: non-PNP Relevant lines from your dmesg: dc0: Intel 21143 10/100BaseTX at device 13.0 on pci0 dc0: couldn't map ports/memory device_probe_and_attach: dc0 attach returned 6 If you look down a ways, you'll also see that you're going to have USB trouble if we don't address this issue. I'm still looking about a bit. If we can get the NIC recognized, then fixing rc.conf should be easy... HTH, KDK - Original Message - From: Thomas Connolly [EMAIL PROTECTED] To: Kevin D. Kinsey, DaleCo, S.P. [EMAIL PROTECTED]; Thomas Connolly [EMAIL PROTECTED]; [EMAIL PROTECTED]; 'Jack L. Stone' [EMAIL PROTECTED] Cc: 'Brian' [EMAIL PROTECTED]; [EMAIL PROTECTED] Sent: Monday, December 09, 2002 9:47 PM Subject: RE: Ethernet card problem Kevin, Here is the files you asked me to post. Again thanks everyone for your continued support. I will be looking forward to your reply. -Original Message- From: Kevin D. Kinsey, DaleCo, S.P. [mailto:[EMAIL PROTECTED]] Sent: Monday, December 09, 2002 3:23 PM To: Thomas Connolly; [EMAIL PROTECTED]; 'Jack L. Stone' Cc: 'Brian'; [EMAIL PROTECTED] Subject: Re: Ethernet card problem From: Thomas Connolly [EMAIL PROTECTED] Sent: Monday, December 09, 2002 4:15 PM Subject: RE: Ethernet card problem I actually installed from CD and won't recognize my NIC. I selected the ed0 NIC from sysinstall because I wasn't sure what I was supposed to use for my card (Kingston KNE100TX - dc(4)). When I got to the configuration screen, there was no Ethernet card listed. I am confused on what to do next. What I'm haring is that I have to install miibus, then I have to edit /etc/rc.conf. Do I have that right? Thanks again, Thomas Connolly If you're using the GENERIC kernel, miibus should already be enabled. As to rc.conf, see below. If you installed from CD, and therefore have a working system, please post the output of: $dmesg If you're able, pipe it to a .txt file and attach it, otherwise copy/paste to your email program. $dmesg attach.txt That might show us if there is a problem at device probe time. It would be worth your time to look at /etc/rc.conf, because it might be easy to spot if sysinstall actually wrote the file using ed0 instead of dc0. If so, changing it would be a hurdle on our way to fixing the issue. You could also send us output from ifconfig -a, but it sounds as if that's already been decided, and dc0 isn't in there. KDK To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
Re: Ethernet card problem
On Dec 09, at 08:47 PM, Thomas Connolly wrote: In another thread, Thomas wrote: My NIC is a pci card. Do I still have to mess with my BIOS? My bad. I thought you wrote it was an ISA card, but that was Kevin, making an observation: OK, he's got a Kingston (generally dc driver) and is trying to do sysinstall and d-load over NIC. IME it doesn't matter what you pick in the configuration section of sysinstall whatever's first should work, because those are just old nonPNP ISA NIC drivers. I inferred that the NIC was ISA, where Kevin wrote that the driver is ISA. You might have to, yes. See below. Copyright (c) 1992-2002 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.7-RELEASE #0: Wed Oct 9 15:08:34 GMT 2002 [EMAIL PROTECTED]:/usr/obj/usr/src/sys/GENERIC Timecounter i8254 frequency 1193182 Hz CPU: Pentium II/Pentium II Xeon/Celeron (347.67-MHz 686-class CPU) Origin = GenuineIntel Id = 0x651 Stepping = 1 Features=0x183f9ffFPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR real memory = 134217728 (131072K bytes) config di sn0 config di lnc0 config di ie0 config di fe0 config di cs0 config di bt0 config di aic0 config di aha0 config di adv0 config q OK, you disabled things with conflicting IRQs and other not-needed-here stuff. Good. avail memory = 125435904 (122496K bytes) Preloaded elf kernel kernel at 0xc050f000. Preloaded userconfig_script /boot/kernel.conf at 0xc050f09c. Pentium Pro MTRR support enabled md0: Malloc disk Using $PIR table, 8 entries at 0xc00fdf40 npx0: math processor on motherboard npx0: INT 16 interface pcib0: Intel 82443BX (440 BX) host to PCI bridge on motherboard pci0: PCI bus on pcib0 pcib1: Intel 82443BX (440 BX) PCI-PCI (AGP) bridge at device 1.0 on pci0 pci1: PCI bus on pcib1 pci1: Matrox MGA G100 AGP graphics accelerator at 0.0 irq 9 isab0: Intel 82371AB PCI to ISA bridge at device 4.0 on pci0 isa0: ISA bus on isab0 atapci0: Intel PIIX4 ATA33 controller port 0xfcf0-0xfcff at device 4.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 uhci0: Intel 82371AB/EB (PIIX4) USB controller at device 4.2 on pci0 uhci0: Could not map ports device_probe_and_attach: uhci0 attach returned 6 chip1: Intel 82371AB Power management controller port 0x2180-0x218f at device 4.3 on pci0 I'm not sure what this should be, but I've seem chip1 entries occur when there's hardware that the kernel isn't prepped for. ICH chipsets come to mind, for instance. This shouldn't be fatal, and probably isn't related to your NIC. dc0: Intel 21143 10/100BaseTX at device 13.0 on pci0 dc0: couldn't map ports/memory device_probe_and_attach: dc0 attach returned 6 There's your dc(4) driver trying to initialize. I don't know what the 6 return value specifically is, but it can't set up its I/O. This leads me to believe that yes, you may have to twiddle ISA/PnP settings in your BIOS. In BIOS, you should be able to zero in on the PCI bus stuff easily enough. Within that, several slot options. I can't tell you specifically what to look for or change though; different BIOSes use different words and phrases to describe the same things. A shot in the dark: Disable Plug-n-Play. Best I can offer. G'Luck, and don't give up yet. Dave -- __ __ \__ \D. J. HAWKEY JR. / __/ \/\ [EMAIL PROTECTED]/\/ http://www.visi.com/~hawkeyd/ To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
Re: Ethernet card problem
From: D J Hawkey Jr [EMAIL PROTECTED] To: Thomas Connolly [EMAIL PROTECTED] Cc: Kevin D. Kinsey, DaleCo, S.P. [EMAIL PROTECTED]; Jack L. Stone [EMAIL PROTECTED]; 'Brian' [EMAIL PROTECTED]; [EMAIL PROTECTED] Sent: Tuesday, December 10, 2002 8:35 AM Subject: Re: Ethernet card problem On Dec 09, at 08:47 PM, Thomas Connolly wrote: In another thread, Thomas wrote: My NIC is a pci card. Do I still have to mess with my BIOS? [...] pci1: Matrox MGA G100 AGP graphics accelerator at 0.0 irq 9 I'd say this is not very good ^ [...] uhci0: Intel 82371AB/EB (PIIX4) USB controller at device 4.2 on pci0 uhci0: Could not map ports device_probe_and_attach: uhci0 attach returned 6 chip1: Intel 82371AB Power management controller port 0x2180-0x218f at device 4.3 on pci0 [...] dc0: Intel 21143 10/100BaseTX at device 13.0 on pci0 dc0: couldn't map ports/memory device_probe_and_attach: dc0 attach returned 6 [...] Looks like there's still some conflict (irq?) In BIOS, you should be able to zero in on the PCI bus stuff easily enough. Within that, several slot options. I can't tell you specifically what to look for or change though; different BIOSes use different words and phrases to describe the same things. A shot in the dark: Disable Plug-n-Play. One more shot-in-the-dark: In the BIOS near PnP OS: Yes/No (Choose No, as others said) you'll see the line something like Reset configuration (data) Make it Yes, and exit from BIOS with Save, then BIOS will be forced to reassign PnP/PCI resources for your hardware. This helped me a number of times. Oh, and when you boot off CD first time, you can select Visual config. Delete here _everyting_ you are sure you don't need (or have). This will simplify device probing a little. HTH, Igor Best I can offer. G'Luck, and don't give up yet. Dave To Unsubscribe: send mail to [EMAIL PROTECTED] with unsubscribe freebsd-questions in the body of the message
