Re: CAM timeouts at startup
On Mon, Apr 10, 2017, Chris H wrote: > > In the past, when I've run into this issue. I add the following to > loader.conf(5) > > kern.cam.boot_delay="" > You'll want to tune it to find a "sweet spot". > fe; on one of my boxes, it reads: > kern.cam.boot_delay="7000" > which is 7 seconds. Heya Chris, thanks for the reply. Trying it with the defaults from /boot/defaults/loader.conf doesn't seem to help so far, but I'll keep seeing if there's a sweet spot to discover. -- Mahlon E. Smith http://www.martini.nu/ signature.asc Description: PGP signature
Re: CAM timeouts at startup
On Mon, 10 Apr 2017 10:49:59 -0700 "Mahlon E. Smith"wrote > Hi. Got some new machines running 11.0-RELEASE-p8 with a small pile of SSD > in them. > > Getting some strange CAM timeouts at boot, that dramatically delay > startup times. These errors don't happen at all after boot, everything > seems just fine. > > Any clues / tuning suggestions are appreciated. > > > Relevant stuff from dmesg: > > mpr0: port 0x3000-0x30ff mem > 0x9200-0x9200,0x91f0-0x91ff at device 0.0 numa-domain 0 on > pci3 mpr0: IOCFacts : > MsgVersion: 0x205 > HeaderVersion: 0x2a00 > IOCNumber: 0 > IOCExceptions: 0x0 > MaxChainDepth: 128 > NumberOfPorts: 1 > RequestCredit: 9680 > ProductID: 0x2221 > IOCRequestFrameSize: 32 > MaxInitiators: 0 > MaxTargets: 544 > MaxSasExpanders: 125 > MaxEnclosures: 126 > HighPriorityCredit: 124 > MaxReplyDescriptorPostQueueDepth: 65504 > ReplyFrameSize: 32 > MaxVolumes: 0 > MaxDevHandle: 677 > MaxPersistentEntries: 240 > mpr0: Firmware: 13.00.00.00, Driver: 13.01.00.00-fbsd > mpr0: IOCCapabilities: > 7a85c stDisc> > > da0 at mpr0 bus 0 scbus0 target 19 lun 0 > da0: Fixed Direct Access SPC-4 SCSI device > da0: Serial Number S2HTNX0H701448 > da0: 1200.000MB/s transfers > da0: Command Queueing enabled > da0: 915715MB (1875385008 512 byte sectors) > da0: quirks=0x8<4K> > > > mpr0: Sending reset from mprsas_send_abort for target ID 19 > mpr0: Unfreezing devq for target ID 19 > (da0:mpr0:0:19:0): READ(10). CDB: 28 00 6f c8 1a af 00 00 01 00 > (da0:mpr0:0:19:0): CAM status: Command timeout > (da0:mpr0:0:19:0): Retrying command > (da0:mpr0:0:19:0): READ(10). CDB: 28 00 6f c8 1a af 00 00 01 00 > (da0:mpr0:0:19:0): CAM status: SCSI Status Error > (da0:mpr0:0:19:0): SCSI status: Check Condition > (da0:mpr0:0:19:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, > or bus device reset occurred) (da0:mpr0:0:19:0): Retrying command (per > sense data) (noperiph:mpr0:0:4294967295:0): SMID 2 Aborting > command 0xfe00026066c0 mpr0: Sending reset from mprsas_send_abort for > target ID 20 mpr0: Unfreezing devq for target ID 20 > (da1:mpr0:0:20:0): READ(10). CDB: 28 00 6f c8 1a af 00 00 01 00 > (da1:mpr0:0:20:0): CAM status: Command timeout > (da1:mpr0:0:20:0): Retrying command > (da1:mpr0:0:20:0): READ(10). CDB: 28 00 6f c8 1a af 00 00 01 00 > (da1:mpr0:0:20:0): CAM status: SCSI Status Error > (da1:mpr0:0:20:0): SCSI status: Check Condition > (da1:mpr0:0:20:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, > or bus device reset occurred) (da1:mpr0:0:20:0): Retrying command (per > sense data) (noperiph:mpr0:0:4294967295:0): SMID 3 Aborting > command 0xfe0002609750 mpr0: Sending reset from mprsas_send_abort for > target ID 21 (da2:mpr0:0:21:0): READ(10). CDB: 28 00 6f c8 1a af 00 00 01 > 00 mpr0: (da2:mpr0:0:21:0): CAM status: Command timeout > Unfreezing devq for target ID 21 > (da2:mpr0:0:21:0): Retrying command > (da2:mpr0:0:21:0): READ(10). CDB: 28 00 6f c8 1a af 00 00 01 00 > (da2:mpr0:0:21:0): CAM status: SCSI Status Error > (da2:mpr0:0:21:0): SCSI status: Check Condition > (da2:mpr0:0:21:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, > or bus device reset occurred) (da2:mpr0:0:21:0): Retrying command (per > sense data) (noperiph:mpr0:0:4294967295:0): SMID 4 Aborting > command 0xfe000260c7e0 mpr0: Sending reset from mprsas_send_abort for > target ID 22 mpr0: Unfreezing devq for target ID 22 > (da3:mpr0:0:22:0): READ(10). CDB: 28 00 6f c8 1a af 00 00 01 00 > (da3:mpr0:0:22:0): CAM status: Command timeout > (da3:mpr0:0:22:0): Retrying command > (da3:mpr0:0:22:0): READ(10). CDB: 28 00 6f c8 1a af 00 00 01 00 > (da3:mpr0:0:22:0): CAM status: SCSI Status Error > (da3:mpr0:0:22:0): SCSI status: Check Condition > (da3:mpr0:0:22:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, > or bus device reset occurred) (da3:mpr0:0:22:0): Retrying command (per > sense data) (noperiph:mpr0:0:4294967295:0): SMID 5 Aborting > command 0xfe0002614f10 mpr0: Sending reset from mprsas_send_abort for > target ID 25 mpr0: Unfreezing devq for target ID 25 > (da6:mpr0:0:25:0): READ(10). CDB: 28 00 6f c8 1a af 00 00 01 00 > (da6:mpr0:0:25:0): CAM status: Command timeout > (da6:mpr0:0:25:0): Retrying command > (da6:mpr0:0:25:0): READ(10). CDB: 28 00 6f c8 1a af 00 00 01 00 > (da6:mpr0:0:25:0): CAM status: SCSI Status Error > (da6:mpr0:0:25:0): SCSI status: Check
CAM timeouts at startup
Hi. Got some new machines running 11.0-RELEASE-p8 with a small pile of SSD in them. Getting some strange CAM timeouts at boot, that dramatically delay startup times. These errors don't happen at all after boot, everything seems just fine. Any clues / tuning suggestions are appreciated. Relevant stuff from dmesg: mpr0: port 0x3000-0x30ff mem 0x9200-0x9200,0x91f0-0x91ff at device 0.0 numa-domain 0 on pci3 mpr0: IOCFacts : MsgVersion: 0x205 HeaderVersion: 0x2a00 IOCNumber: 0 IOCExceptions: 0x0 MaxChainDepth: 128 NumberOfPorts: 1 RequestCredit: 9680 ProductID: 0x2221 IOCRequestFrameSize: 32 MaxInitiators: 0 MaxTargets: 544 MaxSasExpanders: 125 MaxEnclosures: 126 HighPriorityCredit: 124 MaxReplyDescriptorPostQueueDepth: 65504 ReplyFrameSize: 32 MaxVolumes: 0 MaxDevHandle: 677 MaxPersistentEntries: 240 mpr0: Firmware: 13.00.00.00, Driver: 13.01.00.00-fbsd mpr0: IOCCapabilities: 7a85cda0 at mpr0 bus 0 scbus0 target 19 lun 0 da0: Fixed Direct Access SPC-4 SCSI device da0: Serial Number S2HTNX0H701448 da0: 1200.000MB/s transfers da0: Command Queueing enabled da0: 915715MB (1875385008 512 byte sectors) da0: quirks=0x8<4K> mpr0: Sending reset from mprsas_send_abort for target ID 19 mpr0: Unfreezing devq for target ID 19 (da0:mpr0:0:19:0): READ(10). CDB: 28 00 6f c8 1a af 00 00 01 00 (da0:mpr0:0:19:0): CAM status: Command timeout (da0:mpr0:0:19:0): Retrying command (da0:mpr0:0:19:0): READ(10). CDB: 28 00 6f c8 1a af 00 00 01 00 (da0:mpr0:0:19:0): CAM status: SCSI Status Error (da0:mpr0:0:19:0): SCSI status: Check Condition (da0:mpr0:0:19:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred) (da0:mpr0:0:19:0): Retrying command (per sense data) (noperiph:mpr0:0:4294967295:0): SMID 2 Aborting command 0xfe00026066c0 mpr0: Sending reset from mprsas_send_abort for target ID 20 mpr0: Unfreezing devq for target ID 20 (da1:mpr0:0:20:0): READ(10). CDB: 28 00 6f c8 1a af 00 00 01 00 (da1:mpr0:0:20:0): CAM status: Command timeout (da1:mpr0:0:20:0): Retrying command (da1:mpr0:0:20:0): READ(10). CDB: 28 00 6f c8 1a af 00 00 01 00 (da1:mpr0:0:20:0): CAM status: SCSI Status Error (da1:mpr0:0:20:0): SCSI status: Check Condition (da1:mpr0:0:20:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred) (da1:mpr0:0:20:0): Retrying command (per sense data) (noperiph:mpr0:0:4294967295:0): SMID 3 Aborting command 0xfe0002609750 mpr0: Sending reset from mprsas_send_abort for target ID 21 (da2:mpr0:0:21:0): READ(10). CDB: 28 00 6f c8 1a af 00 00 01 00 mpr0: (da2:mpr0:0:21:0): CAM status: Command timeout Unfreezing devq for target ID 21 (da2:mpr0:0:21:0): Retrying command (da2:mpr0:0:21:0): READ(10). CDB: 28 00 6f c8 1a af 00 00 01 00 (da2:mpr0:0:21:0): CAM status: SCSI Status Error (da2:mpr0:0:21:0): SCSI status: Check Condition (da2:mpr0:0:21:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred) (da2:mpr0:0:21:0): Retrying command (per sense data) (noperiph:mpr0:0:4294967295:0): SMID 4 Aborting command 0xfe000260c7e0 mpr0: Sending reset from mprsas_send_abort for target ID 22 mpr0: Unfreezing devq for target ID 22 (da3:mpr0:0:22:0): READ(10). CDB: 28 00 6f c8 1a af 00 00 01 00 (da3:mpr0:0:22:0): CAM status: Command timeout (da3:mpr0:0:22:0): Retrying command (da3:mpr0:0:22:0): READ(10). CDB: 28 00 6f c8 1a af 00 00 01 00 (da3:mpr0:0:22:0): CAM status: SCSI Status Error (da3:mpr0:0:22:0): SCSI status: Check Condition (da3:mpr0:0:22:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred) (da3:mpr0:0:22:0): Retrying command (per sense data) (noperiph:mpr0:0:4294967295:0): SMID 5 Aborting command 0xfe0002614f10 mpr0: Sending reset from mprsas_send_abort for target ID 25 mpr0: Unfreezing devq for target ID 25 (da6:mpr0:0:25:0): READ(10). CDB: 28 00 6f c8 1a af 00 00 01 00 (da6:mpr0:0:25:0): CAM