What do you mean?
Changing the channel configuration on iwconfig will lower my attenuation?
Here is some more information:
$ modprobe bcm43xx
$ dmesg
bcm43xx driver
ACPI: PCI Interrupt :05:02.0[A] - GSI 20 (level, low) - IRQ 20
bcm43xx: Chip ID 0x4318, rev 0x2
bcm43xx: Number of cores: 4
bcm43xx: Core 0: ID 0x800, rev 0xd, vendor 0x4243
bcm43xx: Core 1: ID 0x812, rev 0x9, vendor 0x4243
bcm43xx: Core 2: ID 0x804, rev 0xc, vendor 0x4243
bcm43xx: Core 3: ID 0x80d, rev 0x7, vendor 0x4243
bcm43xx: PHY connected
bcm43xx: Detected PHY: Analog: 3, Type 2, Revision 7
bcm43xx: Detected Radio: ID: 8205017f (Manuf: 17f Ver: 2050 Rev: 8)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
bcm43xx: PHY connected
bcm43xx: Microcode rev 0x127, pl 0xe (2005-04-18 02:36:27)
bcm43xx: Radio turned on
bcm43xx: Radio disabled by hardware
bcm43xx: ASSERTION FAILED (radio_attenuation 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1489:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1489:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1489:bcm43xx_find_lopair()
bcm43xx: Chip initialized
bcm43xx: 32-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
ADDRCONF(NETDEV_UP): eth1: link is not ready
bcm43xx: ASSERTION FAILED (radio_attenuation 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1489:bcm43xx_find_lopair()
bcm43xx: Radio hardware status changed to enabled
$ iwconfig eth1 essid spot_piso2
$ tail /var/log/messages
Oct 15 13:45:18 lisa bcm43xx: ASSERTION FAILED (radio_attenuation
10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1489:bcm43xx_find_lopair()
Oct 15 13:45:19 lisa SoftMAC: Associate: Scanning for networks first.
Oct 15 13:45:20 lisa SoftMAC: Scanning finished: scanned 13 channels
starting with channel 1
Oct 15 13:45:20 lisa SoftMAC: Queueing Authentication Request to
00:0c:41:14:e3:fb
Oct 15 13:45:20 lisa SoftMAC: Cannot associate without being
authenticated, requested authentication
Oct 15 13:45:20 lisa SoftMAC: Sent Authentication Request to 00:0c:41:14:e3:fb.
Oct 15 13:45:20 lisa SoftMAC: Open Authentication completed with
00:0c:41:14:e3:fb
Oct 15 13:45:20 lisa SoftMAC: sent association request!
Oct 15 13:45:20 lisa SoftMAC: associating failed (reason: 0xa)!
$ iwconfig eth1
eth1 IEEE 802.11b/g ESSID:spot_piso2 Nickname:Broadcom 4318
Mode:Managed Frequency=2.437 GHz Access Point: Invalid
Bit Rate=1 Mb/s Tx-Power=18 dBm
RTS thr:off Fragment thr:off
Encryption key:off
Link Quality=0/100 Signal level=0 dBm Noise level=0 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
$ dhcpcd eth1
$ tail /var/log/messages
Oct 15 13:44:25 lisa dhcpcd[4594]: eth1: dhcpcd 3.0.16 starting
Oct 15 13:44:25 lisa dhcpcd[4594]: eth1: hardware address = 00:14:a5:71:28:77
Oct 15 13:44:25 lisa dhcpcd[4594]: eth1: broadcasting for a lease
Oct 15 13:44:45 lisa dhcpcd[4594]: eth1: timed out
Oct 15 13:44:45 lisa dhcpcd[4594]: eth1: exiting
On 10/15/07, Dan Farrell [EMAIL PROTECTED] wrote:
On Mon, 15 Oct 2007 13:48:23 +
Eduardo Otubo [EMAIL PROTECTED] wrote:
Hi everyone,
I am running a kernel-2.6.23 and wifi bcm43xx on my Compaq Presário
v2000. And my Wifi doesn't work. My module is compiled built-in, and
when I start my interface:
$ ifconfig eth1 up
I have this on my dmesg:
bcm43xx: PHY connected
bcm43xx: Microcode rev 0x127, pl 0xe (2005-04-18 02:36:27)
bcm43xx: Radio turned on
bcm43xx: Radio enabled by hardware
bcm43xx: ASSERTION FAILED (radio_attenuation 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1489:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1489:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1489:bcm43xx_find_lopair()
bcm43xx: Chip initialized
bcm43xx: 32-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
bcm43xx: ASSERTION FAILED (radio_attenuation 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1489:bcm43xx_find_lopair()
I can connect on SOME networks, encrypted or not. I mean, I do
connect, but I dont recieve any DHCP packs. When I connect (with DHCP,
or not) I keep connected for a little time, then the link just falls.
Any idea?
Hmm. So the radio attenuation is too high?
here:
http://lists.berlios.de/pipermail/bcm43xx-dev/2006-October/003000.html
they recommend switching your network to a different channel.
--
[EMAIL PROTECTED] mailing list
--
Eduardo Otubo
Linux Registered User #424252
http://z3r00.blogspot.com/
|_|0|_|
|_|_|0|
|0|0|0|
--
[EMAIL PROTECTED] mailing list
