Re: [gentoo-user] wpa_supplicant confusion
On Friday 06 June 2008 14:36:14 Mick wrote: Yep. I did manage to get it working with wpa_supplicant (or so I thought . . . ) # lsmod | grep rt2 rt2500usb 21728 0 rt2x00usb 8576 1 rt2500usb rt2x00lib 14944 2 rt2500usb,rt2x00usb Am I on a hiding to nothing? I thought that if it made it into the kernel it would be alright to use. When I was downloading the rt2x00 from cvs it was a bit of a hit and miss affair. The rt2x00 driver works for some chipsets, but the rt2500usb doesn't seem to work at all. If you check the kernel config you may still see it marked as experimental. Better to use a CVS build (not in portage IIRC) of rt2570 and a current kernel than to try with rt2500usb at this time. That is what I am doing, with wpa using the iwpriv commands. -- gentoo-user@lists.gentoo.org mailing list
[gentoo-user] wpa_supplicant confusion
I am not sure I can explain this: I can connect to an AP (using WEP), but only after I run # iwconfig wlan0 ap auto Within the next few seconds I get an IP via dhcpcd and I can immediately connect to the Internet, but very unreliably. Within a few seconds it seems that the link goes down, i.e. I can no longer ping Internet addresses, or the AP, despite iwconfig showing that all is fine connection wise: # iwconfig wlan0 wlan0 IEEE 802.11g ESSID:daddy Mode:Managed Frequency:2.442 GHz Access Point: 00:18:4D:AE:55:2C Bit Rate=12 Mb/s Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2346 B Encryption key:8B7B-9671-89 Link Quality=31/100 Signal level=-56 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 wpa_cli also shows that the connection is OK: status bssid=00:18:4d:ae:55:2c ssid=daddy id=2 pairwise_cipher=WEP-40 group_cipher=WEP-40 key_mgmt=NONE wpa_state=COMPLETED ip_address=192.168.0.9 Ping-ing the AP has some ridiculous latency, or it fails completely: $ ping -c 3 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. 64 bytes from 192.168.0.1: icmp_seq=1 ttl=255 time=6737 ms 64 bytes from 192.168.0.1: icmp_seq=2 ttl=255 time=6725 ms 64 bytes from 192.168.0.1: icmp_seq=3 ttl=255 time=7736 ms --- 192.168.0.1 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2009ms rtt min/avg/max/mdev = 6725.875/7066.811/7736.602/473.648 ms, pipe 3 This is what's in the wpa_supplicant conf: network={ ssid=daddy bssid=00:18:4D:AE:55:2C key_mgmt=NONE # mode=managed wep_key0=8B7B967189 # wep_key1=BA6889DB39 # wep_key2=D3D68AA753 # wep_key3=35116656AB wep_tx_keyidx=0 group=WEP40 priority=4 } Any idea? -- Regards, Mick signature.asc Description: This is a digitally signed message part.
Re: [gentoo-user] wpa_supplicant confusion
Hello On Fri, Jun 06, 2008 at 06:15:11PM +0100, Mick wrote: wlan0 IEEE 802.11g ESSID:daddy Mode:Managed Frequency:2.442 GHz Access Point: 00:18:4D:AE:55:2C Bit Rate=12 Mb/s Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2346 B Encryption key:8B7B-9671-89 Link Quality=31/100 Signal level=-56 dBm I do not know your card, but mine works with link quality above 60/100, below that doesn't do much. The ping times are because there are link-level retransmits, so it tries many times and it sometimes succeeds. If you get closer to the AP, is it still a problem? -- All flame and insults will go to /dev/null (if they fit) Michal 'vorner' Vaner pgp5u8KSLjqAc.pgp Description: PGP signature
Re: [gentoo-user] wpa_supplicant confusion
On Friday 06 June 2008 12:15:11 Mick wrote: Within the next few seconds I get an IP via dhcpcd and I can immediately connect to the Internet, but very unreliably. Within a few seconds it seems that the link goes down, i.e. I can no longer ping Internet addresses, or the AP, despite iwconfig showing that all is fine connection wise: What driver are you using? This sounds a lot like what rt2500usb (part of the rt2x00 project) does, when it associates with an AP at all BTW, did you really send your wep keys to the world? :) You may want to change them... -- gentoo-user@lists.gentoo.org mailing list
Re: [gentoo-user] wpa_supplicant confusion
On Friday 06 June 2008, Michal 'vorner' Vaner wrote: Hello On Fri, Jun 06, 2008 at 06:15:11PM +0100, Mick wrote: wlan0 IEEE 802.11g ESSID:daddy Mode:Managed Frequency:2.442 GHz Access Point: 00:18:4D:AE:55:2C Bit Rate=12 Mb/s Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2346 B Encryption key:8B7B-9671-89 Link Quality=31/100 Signal level=-56 dBm I do not know your card, but mine works with link quality above 60/100, below that doesn't do much. The ping times are because there are link-level retransmits, so it tries many times and it sometimes succeeds. If you get closer to the AP, is it still a problem? It's a USB dongle: Bus 002 Device 004: ID 050d:7050 Belkin Components F5D7050 ver 1000 WiFi I have moved right next to the AP and notice the same weird behaviour. -- Regards, Mick signature.asc Description: This is a digitally signed message part.
Re: [gentoo-user] wpa_supplicant confusion
On Friday 06 June 2008, Jonathan Fosburgh wrote: On Friday 06 June 2008 12:15:11 Mick wrote: Within the next few seconds I get an IP via dhcpcd and I can immediately connect to the Internet, but very unreliably. Within a few seconds it seems that the link goes down, i.e. I can no longer ping Internet addresses, or the AP, despite iwconfig showing that all is fine connection wise: What driver are you using? This sounds a lot like what rt2500usb (part of the rt2x00 project) does, when it associates with an AP at all Yep. I did manage to get it working with wpa_supplicant (or so I thought . . . ) # lsmod | grep rt2 rt2500usb 21728 0 rt2x00usb 8576 1 rt2500usb rt2x00lib 14944 2 rt2500usb,rt2x00usb Am I on a hiding to nothing? I thought that if it made it into the kernel it would be alright to use. When I was downloading the rt2x00 from cvs it was a bit of a hit and miss affair. BTW, did you really send your wep keys to the world? :) You may want to change them... Nah, not important. I'm in the middle of nowhere to be honest visiting a friend. Also, WEP encryption is rather trivial to crack, especially so with a 40bit key. :p -- Regards, Mick signature.asc Description: This is a digitally signed message part.
Re: [gentoo-user] wpa_supplicant confusion
On Friday 06 June 2008, Michal 'vorner' Vaner wrote: Hello On Fri, Jun 06, 2008 at 06:15:11PM +0100, Mick wrote: wlan0 IEEE 802.11g ESSID:daddy Mode:Managed Frequency:2.442 GHz Access Point: 00:18:4D:AE:55:2C Bit Rate=12 Mb/s Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2346 B Encryption key:8B7B-9671-89 Link Quality=31/100 Signal level=-56 dBm I do not know your card, but mine works with link quality above 60/100, below that doesn't do much. The ping times are because there are link-level retransmits, so it tries many times and it sometimes succeeds. If you get closer to the AP, is it still a problem? Ahh, just noticed this USB unclaimed message in lshw: *-usbhost product: UHCI Host Controller vendor: Linux 2.6.24-gentoo-r8 uhci_hcd physical id: 1 bus info: [EMAIL PROTECTED] logical name: usb2 version: 2.06 capabilities: usb-1.10 configuration: maxpower=0mA slots=2 speed=12.0MB/s *-usb UNCLAIMED description: Generic USB device product: Belkin 54g USB Network Adapter vendor: Belkin physical id: 1 bus info: [EMAIL PROTECTED]:1 version: 0.01 capabilities: usb-2.00 configuration: maxpower=300mA speed=12.0MB/s Should it be so? -- Regards, Mick signature.asc Description: This is a digitally signed message part.