Re: [gmx-users] Continuing runs from 4.5.4 in 4.6.3
On Oct 23, 2013 7:24 AM, rajat desikan rajatdesi...@gmail.com wrote: Hi, We recently had a software upgrade in our cluster from gromacs 4.5.4. to gromacs 4.6.3.. I need to continue an earlier simulation that had been run in 4.5.4. using the .cpt, .tpr and .mdp. Are there any issues with continuing these runs in 4.6.3.? Can I concatenate these trajectories for later analysis? This is not recommended. Even if it works, the trajectory is discontinuous, and the years of accumulated bug fixes, and complete re-implementation of the kernels in 4.6.3, are likely to make the discontinuity observable. Upgrading within a minor release (4.5.4 - 4.5.7, 4.6 - 4.6.3) is intended to work (modulo relevant bug fixes), but would still tend to make your reviewer nervous. Mark I notice that I cannot use a 4.6.3 .cpt and .tpr in 4.5.4. Any input will be appreciated. Thanks. -- Rajat Desikan (Ph.D Scholar) Prof. K. Ganapathy Ayappa's Lab (no 13), Dept. of Chemical Engineering, Indian Institute of Science, Bangalore -- gmx-users mailing listgmx-users@gromacs.org http://lists.gromacs.org/mailman/listinfo/gmx-users * Please search the archive at http://www.gromacs.org/Support/Mailing_Lists/Search before posting! * Please don't post (un)subscribe requests to the list. Use the www interface or send it to gmx-users-requ...@gromacs.org. * Can't post? Read http://www.gromacs.org/Support/Mailing_Lists -- gmx-users mailing listgmx-users@gromacs.org http://lists.gromacs.org/mailman/listinfo/gmx-users * Please search the archive at http://www.gromacs.org/Support/Mailing_Lists/Search before posting! * Please don't post (un)subscribe requests to the list. Use the www interface or send it to gmx-users-requ...@gromacs.org. * Can't post? Read http://www.gromacs.org/Support/Mailing_Lists
Re: [gmx-users] Continuing runs from 4.5.4 in 4.6.3
Thank you, Mark! On Wed, Oct 23, 2013 at 2:56 PM, Mark Abraham mark.j.abra...@gmail.comwrote: On Oct 23, 2013 7:24 AM, rajat desikan rajatdesi...@gmail.com wrote: Hi, We recently had a software upgrade in our cluster from gromacs 4.5.4. to gromacs 4.6.3.. I need to continue an earlier simulation that had been run in 4.5.4. using the .cpt, .tpr and .mdp. Are there any issues with continuing these runs in 4.6.3.? Can I concatenate these trajectories for later analysis? This is not recommended. Even if it works, the trajectory is discontinuous, and the years of accumulated bug fixes, and complete re-implementation of the kernels in 4.6.3, are likely to make the discontinuity observable. Upgrading within a minor release (4.5.4 - 4.5.7, 4.6 - 4.6.3) is intended to work (modulo relevant bug fixes), but would still tend to make your reviewer nervous. Mark I notice that I cannot use a 4.6.3 .cpt and .tpr in 4.5.4. Any input will be appreciated. Thanks. -- Rajat Desikan (Ph.D Scholar) Prof. K. Ganapathy Ayappa's Lab (no 13), Dept. of Chemical Engineering, Indian Institute of Science, Bangalore -- gmx-users mailing listgmx-users@gromacs.org http://lists.gromacs.org/mailman/listinfo/gmx-users * Please search the archive at http://www.gromacs.org/Support/Mailing_Lists/Search before posting! * Please don't post (un)subscribe requests to the list. Use the www interface or send it to gmx-users-requ...@gromacs.org. * Can't post? Read http://www.gromacs.org/Support/Mailing_Lists -- gmx-users mailing listgmx-users@gromacs.org http://lists.gromacs.org/mailman/listinfo/gmx-users * Please search the archive at http://www.gromacs.org/Support/Mailing_Lists/Search before posting! * Please don't post (un)subscribe requests to the list. Use the www interface or send it to gmx-users-requ...@gromacs.org. * Can't post? Read http://www.gromacs.org/Support/Mailing_Lists -- Rajat Desikan (Ph.D Scholar) Prof. K. Ganapathy Ayappa's Lab (no 13), Dept. of Chemical Engineering, Indian Institute of Science, Bangalore -- gmx-users mailing listgmx-users@gromacs.org http://lists.gromacs.org/mailman/listinfo/gmx-users * Please search the archive at http://www.gromacs.org/Support/Mailing_Lists/Search before posting! * Please don't post (un)subscribe requests to the list. Use the www interface or send it to gmx-users-requ...@gromacs.org. * Can't post? Read http://www.gromacs.org/Support/Mailing_Lists
RE: [gmx-users] Continuing runs from 4.5.4 in 4.6.3
There shouldn't be a problem for that. BTW, can you also enter a ticket at Daigrid.org for this matter? Thanks -Kevin -Original Message- From: gmx-users-boun...@gromacs.org [mailto:gmx-users-boun...@gromacs.org] On Behalf Of rajat desikan Sent: Wednesday, October 23, 2013 1:24 AM To: Discussion list for GROMACS users Subject: [gmx-users] Continuing runs from 4.5.4 in 4.6.3 Hi, We recently had a software upgrade in our cluster from gromacs 4.5.4. to gromacs 4.6.3.. I need to continue an earlier simulation that had been run in 4.5.4. using the .cpt, .tpr and .mdp. Are there any issues with continuing these runs in 4.6.3.? Can I concatenate these trajectories for later analysis? I notice that I cannot use a 4.6.3 .cpt and .tpr in 4.5.4. Any input will be appreciated. Thanks. -- Rajat Desikan (Ph.D Scholar) Prof. K. Ganapathy Ayappa's Lab (no 13), Dept. of Chemical Engineering, Indian Institute of Science, Bangalore -- gmx-users mailing listgmx-users@gromacs.org http://lists.gromacs.org/mailman/listinfo/gmx-users * Please search the archive at http://www.gromacs.org/Support/Mailing_Lists/Search before posting! * Please don't post (un)subscribe requests to the list. Use the www interface or send it to gmx-users-requ...@gromacs.org. * Can't post? Read http://www.gromacs.org/Support/Mailing_Lists -- gmx-users mailing listgmx-users@gromacs.org http://lists.gromacs.org/mailman/listinfo/gmx-users * Please search the archive at http://www.gromacs.org/Support/Mailing_Lists/Search before posting! * Please don't post (un)subscribe requests to the list. Use the www interface or send it to gmx-users-requ...@gromacs.org. * Can't post? Read http://www.gromacs.org/Support/Mailing_Lists
Aw: RE: [gmx-users] Continuing runs from 4.5.4 in 4.6.3
I ran into this, you basically should determine your time frame, and install 4.5.4 if its a problem local (only 1-2 hours), to finish the work, otherwise you need to start from scratch. But I did this with older versions, so do not know about higher versions (such as if theprogrammerseliminated the read version number thing at many of the script initializing things...). The auxillary software does work for analysis, but you end up having to cut things into portions with some aspects, 1/2 one version versus 1/2 the other...but mostly for higher end analysis, not the simplistic ones, such as distance versus hessian matrices or covariance. Stephan Watkins Gesendet:Mittwoch, 23. Oktober 2013 um 16:17 Uhr Von:Kevin Chen fch6...@gmail.com An:Discussion list for GROMACS users gmx-users@gromacs.org Betreff:RE: [gmx-users] Continuing runs from 4.5.4 in 4.6.3 There shouldnt be a problem for that. BTW, can you also enter a ticket at Daigrid.org for this matter? Thanks -Kevin -Original Message- From: gmx-users-boun...@gromacs.org [mailto:gmx-users-boun...@gromacs.org] On Behalf Of rajat desikan Sent: Wednesday, October 23, 2013 1:24 AM To: Discussion list for GROMACS users Subject: [gmx-users] Continuing runs from 4.5.4 in 4.6.3 Hi, We recently had a software upgrade in our cluster from gromacs 4.5.4. to gromacs 4.6.3.. I need to continue an earlier simulation that had been run in 4.5.4. using the .cpt, .tpr and .mdp. Are there any issues with continuing these runs in 4.6.3.? Can I concatenate these trajectories for later analysis? I notice that I cannot use a 4.6.3 .cpt and .tpr in 4.5.4. Any input will be appreciated. Thanks. -- Rajat Desikan (Ph.D Scholar) Prof. K. Ganapathy Ayappas Lab (no 13), Dept. of Chemical Engineering, Indian Institute of Science, Bangalore -- gmx-users mailing list gmx-users@gromacs.org http://lists.gromacs.org/mailman/listinfo/gmx-users * Please search the archive at http://www.gromacs.org/Support/Mailing_Lists/Search before posting! * Please dont post (un)subscribe requests to the list. Use the www interface or send it to gmx-users-requ...@gromacs.org. * Cant post? Read http://www.gromacs.org/Support/Mailing_Lists -- gmx-users mailing list gmx-users@gromacs.org http://lists.gromacs.org/mailman/listinfo/gmx-users * Please search the archive at http://www.gromacs.org/Support/Mailing_Lists/Search before posting! * Please dont post (un)subscribe requests to the list. Use the www interface or send it to gmx-users-requ...@gromacs.org. * Cant post? Read http://www.gromacs.org/Support/Mailing_Lists -- gmx-users mailing listgmx-users@gromacs.org http://lists.gromacs.org/mailman/listinfo/gmx-users * Please search the archive at http://www.gromacs.org/Support/Mailing_Lists/Search before posting! * Please don't post (un)subscribe requests to the list. Use the www interface or send it to gmx-users-requ...@gromacs.org. * Can't post? Read http://www.gromacs.org/Support/Mailing_Lists
[gmx-users] Continuing runs from 4.5.4 in 4.6.3
Hi, We recently had a software upgrade in our cluster from gromacs 4.5.4. to gromacs 4.6.3.. I need to continue an earlier simulation that had been run in 4.5.4. using the .cpt, .tpr and .mdp. Are there any issues with continuing these runs in 4.6.3.? Can I concatenate these trajectories for later analysis? I notice that I cannot use a 4.6.3 .cpt and .tpr in 4.5.4. Any input will be appreciated. Thanks. -- Rajat Desikan (Ph.D Scholar) Prof. K. Ganapathy Ayappa's Lab (no 13), Dept. of Chemical Engineering, Indian Institute of Science, Bangalore -- gmx-users mailing listgmx-users@gromacs.org http://lists.gromacs.org/mailman/listinfo/gmx-users * Please search the archive at http://www.gromacs.org/Support/Mailing_Lists/Search before posting! * Please don't post (un)subscribe requests to the list. Use the www interface or send it to gmx-users-requ...@gromacs.org. * Can't post? Read http://www.gromacs.org/Support/Mailing_Lists