Re: OMAP3 isp single-shot
Hi Laurent, On Friday 25 March 2011 14:10:28 Daniel Lundborg wrote: On Thursday 24 March 2011 11:26:01 Daniel Lundborg wrote: [snip] I can see on the oscilloscope that the sensor is sending something when I trigger it, but no picture is received.. something is a bit vague, can you check the hsync/vsync signals and make sure they're identical in both modes ? I have now tested this and I can say that I am having problems triggering the sensor. I wrongly thought I was triggering the sensor with my other driver correctly, but that was not the case. What I want is to put the Omap ISP to generate a signal (CAM_WEN) to make the camera sensor take a picture. That's not possible. The cam_wen signal is an input to the ISP. The ISP Timing Control module can generate pulses on the cam_shutter, cam_strobe and cam_global_reset signals only. I meant the CAM_WEN pin that should be set as CAM_SHUTTER.. :) What you could do is configure the cam_wen pin as a GPIO and control it using the GPIO framework (either in kernelspace or userspace). In my working mt9v034 driver which is using kernel 2.6.31-rc7 with the patches from http://gitorious.org/omap3camera/mainline/commits/slave I set the ISP to this on power on: isp_reg_and_or(vdev-cam-isp, OMAP3_ISP_IOMEM_MAIN, ISP_TCTRL_CTRL, 0x9a1b63ff, 0x98036000); // Set CAM_GLOBAL_RESET pin as output, enable shutter, set DIVC = 216 What ISP driver version are you using ? isp_reg_and_or has been replaced by isp_reg_clr_set a very long time ago. You should really upgrade. That's what I was trying to do :) isp_reg_and(vdev-cam-isp, OMAP3_ISP_IOMEM_MAIN, ISP_TCTRL_SHUT_DELAY, 0xfe00); // Set no shutter delay isp_reg_and_or(vdev-cam-isp, OMAP3_ISP_IOMEM_MAIN, ISP_TCTRL_SHUT_LENGTH, 0xfe00, 0x03e8); // Set shutter signal length to 1000 (= 1000 * 1/216MHz * 216 = 1 ms) isp_reg_and_or(vdev-cam-isp, OMAP3_ISP_IOMEM_MAIN, ISP_TCTRL_GRESET_LENGTH, 0xfe00, 0x03e8); // Set shutter signal length to 1000 (= 1000 * 1/216MHz * 216 = 1 ms) isp_reg_and(isp_ccdc_dev, OMAP3_ISP_IOMEM_CCDC, ISPCCDC_LSC_CONFIG, ~ISPCCDC_LSC_ENABLE); // Make sure you disable LSC And when I want to take a picture I do: isp_reg_or(vdev-cam-isp, OMAP3_ISP_IOMEM_MAIN, ISP_TCTRL_CTRL, 0x00e0); // Enable shutter (SHUTEN bit = 1) isp_reg_or(vdev-cam-isp, OMAP3_ISP_IOMEM_MAIN, ISP_TCTRL_CTRL, 0x2000); // Start generation of CAM_GLOBAL_RESET signal (GRESETEN bit = 1) When I try to do this in the newer driver I manage to generate a pulse on the CAM_WEN pin, but no VSYNC, HSYNC or data is transmitted. I fail to see how that code can generate a pulse on the cam_wen signal. It should only control the cam_shutter, cam_strobe and cam_global_shutter pins. Am I missing something? Is your sensor correctly configured ? Is there a publicly available datasheet for the MT9V034 ? I found where I was misconfiguring the sensor. I missed setting a bit in the CHIP_CONTROL register. So now my driver is running. :) This is how I set the sensor in shutter mode now: // Set chip to shutter mode temp = mt9v034_read(client, MT9V034_CHIP_CONTROL); temp = 0x0198 | (temp 0xfeff); ret = mt9v034_write(client, MT9V034_CHIP_CONTROL, temp); Thank you, /Daniel -- To unsubscribe from this list: send the line unsubscribe linux-media in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: OMAP3 isp single-shot
Hi Daniel, On Friday 25 March 2011 14:10:28 Daniel Lundborg wrote: On Thursday 24 March 2011 11:26:01 Daniel Lundborg wrote: [snip] I can see on the oscilloscope that the sensor is sending something when I trigger it, but no picture is received.. something is a bit vague, can you check the hsync/vsync signals and make sure they're identical in both modes ? I have now tested this and I can say that I am having problems triggering the sensor. I wrongly thought I was triggering the sensor with my other driver correctly, but that was not the case. What I want is to put the Omap ISP to generate a signal (CAM_WEN) to make the camera sensor take a picture. That's not possible. The cam_wen signal is an input to the ISP. The ISP Timing Control module can generate pulses on the cam_shutter, cam_strobe and cam_global_reset signals only. What you could do is configure the cam_wen pin as a GPIO and control it using the GPIO framework (either in kernelspace or userspace). In my working mt9v034 driver which is using kernel 2.6.31-rc7 with the patches from http://gitorious.org/omap3camera/mainline/commits/slave I set the ISP to this on power on: isp_reg_and_or(vdev-cam-isp, OMAP3_ISP_IOMEM_MAIN, ISP_TCTRL_CTRL, 0x9a1b63ff, 0x98036000); // Set CAM_GLOBAL_RESET pin as output, enable shutter, set DIVC = 216 What ISP driver version are you using ? isp_reg_and_or has been replaced by isp_reg_clr_set a very long time ago. You should really upgrade. isp_reg_and(vdev-cam-isp, OMAP3_ISP_IOMEM_MAIN, ISP_TCTRL_SHUT_DELAY, 0xfe00); // Set no shutter delay isp_reg_and_or(vdev-cam-isp, OMAP3_ISP_IOMEM_MAIN, ISP_TCTRL_SHUT_LENGTH, 0xfe00, 0x03e8); // Set shutter signal length to 1000 (= 1000 * 1/216MHz * 216 = 1 ms) isp_reg_and_or(vdev-cam-isp, OMAP3_ISP_IOMEM_MAIN, ISP_TCTRL_GRESET_LENGTH, 0xfe00, 0x03e8); // Set shutter signal length to 1000 (= 1000 * 1/216MHz * 216 = 1 ms) isp_reg_and(isp_ccdc_dev, OMAP3_ISP_IOMEM_CCDC, ISPCCDC_LSC_CONFIG, ~ISPCCDC_LSC_ENABLE); // Make sure you disable LSC And when I want to take a picture I do: isp_reg_or(vdev-cam-isp, OMAP3_ISP_IOMEM_MAIN, ISP_TCTRL_CTRL, 0x00e0); // Enable shutter (SHUTEN bit = 1) isp_reg_or(vdev-cam-isp, OMAP3_ISP_IOMEM_MAIN, ISP_TCTRL_CTRL, 0x2000); // Start generation of CAM_GLOBAL_RESET signal (GRESETEN bit = 1) When I try to do this in the newer driver I manage to generate a pulse on the CAM_WEN pin, but no VSYNC, HSYNC or data is transmitted. I fail to see how that code can generate a pulse on the cam_wen signal. It should only control the cam_shutter, cam_strobe and cam_global_shutter pins. Am I missing something? Is your sensor correctly configured ? Is there a publicly available datasheet for the MT9V034 ? -- Regards, Laurent Pinchart -- To unsubscribe from this list: send the line unsubscribe linux-media in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: OMAP3 isp single-shot
Hi Laurent,
Hi Daniel,
On Thursday 24 March 2011 11:26:01 Daniel Lundborg wrote:
Daniel Lundborg wrote:
I am successfully using the gumstix overo board together with a
camera
sensor Aptina MT9V034 with the kernel 2.6.35 and patches from
http://git.linuxtv.org/pinchartl/media.git (isp6).
Which branch did you use?
I am using the media-2.6.35-0006-sensors branch which could be found
just a couple of weeks ago. It has the mt9v032 sensor in it. My
mt9v034
driver is based on the mt9v032 code.
Now that the OMAP3 ISP driver is on its way to mainline, I've
reorganized the
repository. You can use the media-2.6.38-0002-sensors branch for
2.6.38.
I can use the media-ctl program and yavta to take pictures in
continous
streaming mode.
media-ctl -r -l 'mt9034 3-0048:0-OMAP3 ISP CCDC:0[1],
OMAP3 ISP
CCDC:1-OMAP3 ISP CCDC output:0[1]'
media-ctl -f 'mt9v034 3-0048:0[SGRBG10 752x480], OMAP3 ISP
CCDC:1[SGRBG10 752x480]
and then:
yavta -f SGRBG10 -s 752x480 -n 1 --capture=1 -F /dev/video2
Is there a way to set the ISP in single shot mode?
Single shot for the ISP is the same as to queue just one buffer. I
assume
the single shot mode is something that the sensor supports?
I have tested setting the mt9v034 in snapshot mode and manually
trigger
the camera, but the ISP does not send a picture. Is there a way
to solve
this with the current OMAP3 isp code?
Do you get any errors, or you just don't get any video buffers?
This is the output from yavta when I put the sensor in streaming
mode:
root@overo:~/yavta# ./yavta -f SGRBG10 -s 752x480 -n 1 --capture=1
-F
/dev/video2
Device /dev/video2 opened: OMAP3 ISP CCDC output (media).
Video format set: width: 752 height: 480 buffer size: 721920
Video format: BA10 (30314142) 752x480
1 buffers requested.
length: 721920 offset: 0
Buffer 0 mapped at address 0x4014d000.
0 (0) [-] 0 721920 bytes 65877.098848 1300958239.111966 0.001 fps
Captured 1 frames in 0.62 seconds (16129.032258 fps,
11643870967.741936 B/s).
1 buffers released.
And the output when putting the sensor in snapshot mode:
root@overo:~/yavta# ./yavta -f SGRBG10 -s 752x480 -n 1 --capture=1
-F
/dev/video2
Device /dev/video2 opened: OMAP3 ISP CCDC output (media).
Video format set: width: 752 height: 480 buffer size: 721920
Video format: BA10 (30314142) 752x480
1 buffers requested.
length: 721920 offset: 0
Buffer 0 mapped at address 0x4014d000.
And it freezes. I can stop yavta with CTRL+C.
Have you tried to trigger the sensor multiple times in a row ?
To put the sensor in snapshot/shutter mode I set the ext_trig = 1 in
the
platform_data structure in my board file.
struct mt9v034_platform_data {
unsigned int clk_pol:1;
unsigned int ext_trig:1;
void (*set_clock)(struct v4l2_subdev *subdev, unsigned int
rate);
};
And in the s_stream I set the chip_control register for the MT9V034
sensor to:
static int mt9v034_s_stream(struct v4l2_subdev *subdev, int enable)
{
struct mt9v034 *mt9v034 = to_mt9v034(subdev);
const u16 chip_clear = mt9v034-pdata-ext_trig? 0x0100 : 0;
const u16 chip_set = mt9v034-pdata-ext_trig? 0x18 :
MT9V034_CHIP_CONTROL_MASTER_MODE | MT9V034_CHIP_CONTROL_DOUT_ENABLE
|
MT9V034_CHIP_CONTROL_SEQUENTIAL;
struct i2c_client *client = v4l2_get_subdevdata(subdev);
struct v4l2_mbus_framefmt *format = mt9v034-format;
struct v4l2_rect *crop = mt9v034-crop;
unsigned int hratio;
unsigned int vratio;
int ret;
if (!enable) {
ret = mt9v034_set_chip_control(mt9v034, chip_clear, chip_set);
if (ret 0)
return ret;
return __mt9v034_set_power(mt9v034, 0);
}
ret = __mt9v034_set_power(mt9v034, 1);
if (ret 0)
return ret;
/* Configure the window size and row/column bin */
hratio = DIV_ROUND_CLOSEST(crop-width, format-width);
vratio = DIV_ROUND_CLOSEST(crop-height, format-height);
ret = mt9v034_write(client, MT9V034_READ_MODE,
(hratio - 1) MT9V034_READ_MODE_ROW_BIN_SHIFT |
(vratio - 1) MT9V034_READ_MODE_COLUMN_BIN_SHIFT);
if (ret 0)
return ret;
ret = mt9v034_write(client, MT9V034_COLUMN_START, crop-left);
if (ret 0)
return ret;
ret = mt9v034_write(client, MT9V034_ROW_START, crop-top);
if (ret 0)
return ret;
ret = mt9v034_write(client, MT9V034_WINDOW_WIDTH, crop-width);
if (ret 0)
return ret;
ret = mt9v034_write(client, MT9V034_WINDOW_HEIGHT, crop-height);
if (ret 0)
return ret;
/* Disable the noise correction algorithm and restore the
controls. */
ret = mt9v034_write(client, MT9V034_ROW_NOISE_CORR_CONTROL, 0);
if (ret 0)
return ret;
v4l2_ctrl_handler_setup(mt9v034-ctrls);
ret = mt9v034_set_chip_control(mt9v034, chip_clear, chip_set);
Re: OMAP3 isp single-shot
Daniel Lundborg wrote: Hello, Hi Daniel, (Cc'ing Laurent.) I am successfully using the gumstix overo board together with a camera sensor Aptina MT9V034 with the kernel 2.6.35 and patches from http://git.linuxtv.org/pinchartl/media.git (isp6). Which branch did you use? I can use the media-ctl program and yavta to take pictures in continous streaming mode. media-ctl -r -l 'mt9034 3-0048:0-OMAP3 ISP CCDC:0[1], OMAP3 ISP CCDC:1-OMAP3 ISP CCDC output:0[1]' media-ctl -f 'mt9v034 3-0048:0[SGRBG10 752x480], OMAP3 ISP CCDC:1[SGRBG10 752x480] and then: yavta -f SGRBG10 -s 752x480 -n 1 --capture=1 -F /dev/video2 Is there a way to set the ISP in single shot mode? Single shot for the ISP is the same as to queue just one buffer. I assume the single shot mode is something that the sensor supports? I have tested setting the mt9v034 in snapshot mode and manually trigger the camera, but the ISP does not send a picture. Is there a way to solve this with the current OMAP3 isp code? Do you get any errors, or you just don't get any video buffers? As the sensor works in streaming mode, are you sure it outputs the image of correct size in the single shot mode? I have before successfully used the isp parts from the Nokia N900 project.. This is nice to hear! :-) Regards, -- Sakari Ailus sakari.ai...@maxwell.research.nokia.com -- To unsubscribe from this list: send the line unsubscribe linux-media in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: SV: OMAP3 isp single-shot
Hi Daniel,
On Thursday 24 March 2011 11:26:01 Daniel Lundborg wrote:
Daniel Lundborg wrote:
I am successfully using the gumstix overo board together with a camera
sensor Aptina MT9V034 with the kernel 2.6.35 and patches from
http://git.linuxtv.org/pinchartl/media.git (isp6).
Which branch did you use?
I am using the media-2.6.35-0006-sensors branch which could be found
just a couple of weeks ago. It has the mt9v032 sensor in it. My mt9v034
driver is based on the mt9v032 code.
Now that the OMAP3 ISP driver is on its way to mainline, I've reorganized the
repository. You can use the media-2.6.38-0002-sensors branch for 2.6.38.
I can use the media-ctl program and yavta to take pictures in continous
streaming mode.
media-ctl -r -l 'mt9034 3-0048:0-OMAP3 ISP CCDC:0[1], OMAP3 ISP
CCDC:1-OMAP3 ISP CCDC output:0[1]'
media-ctl -f 'mt9v034 3-0048:0[SGRBG10 752x480], OMAP3 ISP
CCDC:1[SGRBG10 752x480]
and then:
yavta -f SGRBG10 -s 752x480 -n 1 --capture=1 -F /dev/video2
Is there a way to set the ISP in single shot mode?
Single shot for the ISP is the same as to queue just one buffer. I assume
the single shot mode is something that the sensor supports?
I have tested setting the mt9v034 in snapshot mode and manually trigger
the camera, but the ISP does not send a picture. Is there a way to solve
this with the current OMAP3 isp code?
Do you get any errors, or you just don't get any video buffers?
This is the output from yavta when I put the sensor in streaming mode:
root@overo:~/yavta# ./yavta -f SGRBG10 -s 752x480 -n 1 --capture=1 -F
/dev/video2
Device /dev/video2 opened: OMAP3 ISP CCDC output (media).
Video format set: width: 752 height: 480 buffer size: 721920
Video format: BA10 (30314142) 752x480
1 buffers requested.
length: 721920 offset: 0
Buffer 0 mapped at address 0x4014d000.
0 (0) [-] 0 721920 bytes 65877.098848 1300958239.111966 0.001 fps
Captured 1 frames in 0.62 seconds (16129.032258 fps,
11643870967.741936 B/s).
1 buffers released.
And the output when putting the sensor in snapshot mode:
root@overo:~/yavta# ./yavta -f SGRBG10 -s 752x480 -n 1 --capture=1 -F
/dev/video2
Device /dev/video2 opened: OMAP3 ISP CCDC output (media).
Video format set: width: 752 height: 480 buffer size: 721920
Video format: BA10 (30314142) 752x480
1 buffers requested.
length: 721920 offset: 0
Buffer 0 mapped at address 0x4014d000.
And it freezes. I can stop yavta with CTRL+C.
Have you tried to trigger the sensor multiple times in a row ?
To put the sensor in snapshot/shutter mode I set the ext_trig = 1 in the
platform_data structure in my board file.
struct mt9v034_platform_data {
unsigned int clk_pol:1;
unsigned int ext_trig:1;
void (*set_clock)(struct v4l2_subdev *subdev, unsigned int rate);
};
And in the s_stream I set the chip_control register for the MT9V034
sensor to:
static int mt9v034_s_stream(struct v4l2_subdev *subdev, int enable)
{
struct mt9v034 *mt9v034 = to_mt9v034(subdev);
const u16 chip_clear = mt9v034-pdata-ext_trig? 0x0100 : 0;
const u16 chip_set = mt9v034-pdata-ext_trig? 0x18 :
MT9V034_CHIP_CONTROL_MASTER_MODE | MT9V034_CHIP_CONTROL_DOUT_ENABLE |
MT9V034_CHIP_CONTROL_SEQUENTIAL;
struct i2c_client *client = v4l2_get_subdevdata(subdev);
struct v4l2_mbus_framefmt *format = mt9v034-format;
struct v4l2_rect *crop = mt9v034-crop;
unsigned int hratio;
unsigned int vratio;
int ret;
if (!enable) {
ret = mt9v034_set_chip_control(mt9v034, chip_clear, chip_set);
if (ret 0)
return ret;
return __mt9v034_set_power(mt9v034, 0);
}
ret = __mt9v034_set_power(mt9v034, 1);
if (ret 0)
return ret;
/* Configure the window size and row/column bin */
hratio = DIV_ROUND_CLOSEST(crop-width, format-width);
vratio = DIV_ROUND_CLOSEST(crop-height, format-height);
ret = mt9v034_write(client, MT9V034_READ_MODE,
(hratio - 1) MT9V034_READ_MODE_ROW_BIN_SHIFT |
(vratio - 1) MT9V034_READ_MODE_COLUMN_BIN_SHIFT);
if (ret 0)
return ret;
ret = mt9v034_write(client, MT9V034_COLUMN_START, crop-left);
if (ret 0)
return ret;
ret = mt9v034_write(client, MT9V034_ROW_START, crop-top);
if (ret 0)
return ret;
ret = mt9v034_write(client, MT9V034_WINDOW_WIDTH, crop-width);
if (ret 0)
return ret;
ret = mt9v034_write(client, MT9V034_WINDOW_HEIGHT, crop-height);
if (ret 0)
return ret;
/* Disable the noise correction algorithm and restore the controls. */
ret = mt9v034_write(client, MT9V034_ROW_NOISE_CORR_CONTROL, 0);
if (ret 0)
return ret;
v4l2_ctrl_handler_setup(mt9v034-ctrls);
ret = mt9v034_set_chip_control(mt9v034, chip_clear, chip_set);
return ret;
}
I can see on the oscilloscope that the sensor is sending something when
I trigger it, but no picture is received..
something is a bit
SV: OMAP3 isp single-shot
Hello Sakari,
Daniel Lundborg wrote:
Hello,
Hi Daniel,
(Cc'ing Laurent.)
I am successfully using the gumstix overo board together with a
camera sensor
Aptina MT9V034 with the kernel 2.6.35 and patches from
http://git.linuxtv.org/pinchartl/media.git (isp6).
Which branch did you use?
I am using the media-2.6.35-0006-sensors branch which could be found
just a couple of weeks ago. It has the mt9v032 sensor in it. My mt9v034
driver is based on the mt9v032 code.
I can use the media-ctl program and yavta to take pictures in
continous
streaming mode.
media-ctl -r -l 'mt9034 3-0048:0-OMAP3 ISP CCDC:0[1], OMAP3
ISP
CCDC:1-OMAP3 ISP CCDC output:0[1]'
media-ctl -f 'mt9v034 3-0048:0[SGRBG10 752x480], OMAP3 ISP
CCDC:1[SGRBG10
752x480]
and then:
yavta -f SGRBG10 -s 752x480 -n 1 --capture=1 -F /dev/video2
Is there a way to set the ISP in single shot mode?
Single shot for the ISP is the same as to queue just one buffer. I
assume the single shot mode is something that the sensor supports?
I have tested setting the mt9v034 in snapshot mode and manually
trigger the
camera, but the ISP does not send a picture. Is there a way to solve
this with
the current OMAP3 isp code?
Do you get any errors, or you just don't get any video buffers?
This is the output from yavta when I put the sensor in streaming mode:
root@overo:~/yavta# ./yavta -f SGRBG10 -s 752x480 -n 1 --capture=1 -F
/dev/video2
Device /dev/video2 opened: OMAP3 ISP CCDC output (media).
Video format set: width: 752 height: 480 buffer size: 721920
Video format: BA10 (30314142) 752x480
1 buffers requested.
length: 721920 offset: 0
Buffer 0 mapped at address 0x4014d000.
0 (0) [-] 0 721920 bytes 65877.098848 1300958239.111966 0.001 fps
Captured 1 frames in 0.62 seconds (16129.032258 fps,
11643870967.741936 B/s).
1 buffers released.
And the output when putting the sensor in snapshot mode:
root@overo:~/yavta# ./yavta -f SGRBG10 -s 752x480 -n 1 --capture=1 -F
/dev/video2
Device /dev/video2 opened: OMAP3 ISP CCDC output (media).
Video format set: width: 752 height: 480 buffer size: 721920
Video format: BA10 (30314142) 752x480
1 buffers requested.
length: 721920 offset: 0
Buffer 0 mapped at address 0x4014d000.
And it freezes. I can stop yavta with CTRL+C.
To put the sensor in snapshot/shutter mode I set the ext_trig = 1 in the
platform_data structure in my board file.
struct mt9v034_platform_data {
unsigned int clk_pol:1;
unsigned int ext_trig:1;
void (*set_clock)(struct v4l2_subdev *subdev, unsigned int
rate);
};
And in the s_stream I set the chip_control register for the MT9V034
sensor to:
static int mt9v034_s_stream(struct v4l2_subdev *subdev, int enable)
{
struct mt9v034 *mt9v034 = to_mt9v034(subdev);
const u16 chip_clear = mt9v034-pdata-ext_trig? 0x0100 : 0;
const u16 chip_set = mt9v034-pdata-ext_trig? 0x18 :
MT9V034_CHIP_CONTROL_MASTER_MODE | MT9V034_CHIP_CONTROL_DOUT_ENABLE |
MT9V034_CHIP_CONTROL_SEQUENTIAL;
struct i2c_client *client = v4l2_get_subdevdata(subdev);
struct v4l2_mbus_framefmt *format = mt9v034-format;
struct v4l2_rect *crop = mt9v034-crop;
unsigned int hratio;
unsigned int vratio;
int ret;
if (!enable) {
ret = mt9v034_set_chip_control(mt9v034, chip_clear, chip_set);
if (ret 0)
return ret;
return __mt9v034_set_power(mt9v034, 0);
}
ret = __mt9v034_set_power(mt9v034, 1);
if (ret 0)
return ret;
/* Configure the window size and row/column bin */
hratio = DIV_ROUND_CLOSEST(crop-width, format-width);
vratio = DIV_ROUND_CLOSEST(crop-height, format-height);
ret = mt9v034_write(client, MT9V034_READ_MODE,
(hratio - 1) MT9V034_READ_MODE_ROW_BIN_SHIFT |
(vratio - 1) MT9V034_READ_MODE_COLUMN_BIN_SHIFT);
if (ret 0)
return ret;
ret = mt9v034_write(client, MT9V034_COLUMN_START, crop-left);
if (ret 0)
return ret;
ret = mt9v034_write(client, MT9V034_ROW_START, crop-top);
if (ret 0)
return ret;
ret = mt9v034_write(client, MT9V034_WINDOW_WIDTH, crop-width);
if (ret 0)
return ret;
ret = mt9v034_write(client, MT9V034_WINDOW_HEIGHT, crop-height);
if (ret 0)
return ret;
/* Disable the noise correction algorithm and restore the controls. */
ret = mt9v034_write(client, MT9V034_ROW_NOISE_CORR_CONTROL, 0);
if (ret 0)
return ret;
v4l2_ctrl_handler_setup(mt9v034-ctrls);
ret = mt9v034_set_chip_control(mt9v034, chip_clear, chip_set);
return ret;
}
I can see on the oscilloscope that the sensor is sending something when
I trigger it, but no picture is received..
As the sensor works in streaming mode, are you sure it outputs the
image
of correct size in the single shot mode?
The sensor has the same output in streaming and single shot mode.
I have before successfully used the isp parts from the Nokia N900
project..
This is nice to hear! :-)
Regards,
--
Sakari Ailus
sakari.ai...@maxwell.research.nokia.com
SV: SV: OMAP3 isp single-shot
Hi Laurent, Hi Daniel, On Thursday 24 March 2011 11:26:01 Daniel Lundborg wrote: Daniel Lundborg wrote: I am successfully using the gumstix overo board together with a camera sensor Aptina MT9V034 with the kernel 2.6.35 and patches from http://git.linuxtv.org/pinchartl/media.git (isp6). Which branch did you use? I am using the media-2.6.35-0006-sensors branch which could be found just a couple of weeks ago. It has the mt9v032 sensor in it. My mt9v034 driver is based on the mt9v032 code. Now that the OMAP3 ISP driver is on its way to mainline, I've reorganized the repository. You can use the media-2.6.38-0002-sensors branch for 2.6.38. Ok. I will test that one. --- This is the output from yavta when I put the sensor in streaming mode: root@overo:~/yavta# ./yavta -f SGRBG10 -s 752x480 -n 1 --capture=1 -F /dev/video2 Device /dev/video2 opened: OMAP3 ISP CCDC output (media). Video format set: width: 752 height: 480 buffer size: 721920 Video format: BA10 (30314142) 752x480 1 buffers requested. length: 721920 offset: 0 Buffer 0 mapped at address 0x4014d000. 0 (0) [-] 0 721920 bytes 65877.098848 1300958239.111966 0.001 fps Captured 1 frames in 0.62 seconds (16129.032258 fps, 11643870967.741936 B/s). 1 buffers released. And the output when putting the sensor in snapshot mode: root@overo:~/yavta# ./yavta -f SGRBG10 -s 752x480 -n 1 --capture=1 -F /dev/video2 Device /dev/video2 opened: OMAP3 ISP CCDC output (media). Video format set: width: 752 height: 480 buffer size: 721920 Video format: BA10 (30314142) 752x480 1 buffers requested. length: 721920 offset: 0 Buffer 0 mapped at address 0x4014d000. And it freezes. I can stop yavta with CTRL+C. Have you tried to trigger the sensor multiple times in a row ? No. I will test that. I can see on the oscilloscope that the sensor is sending something when I trigger it, but no picture is received.. something is a bit vague, can you check the hsync/vsync signals and make sure they're identical in both modes ? Ok. Yes this needs more oscilloscope testing. As the sensor works in streaming mode, are you sure it outputs the image of correct size in the single shot mode? The sensor has the same output in streaming and single shot mode. -- Regards, Laurent Pinchart Thanks, Daniel Lundborg daniel.lundb...@prevas.se -- To unsubscribe from this list: send the line unsubscribe linux-media in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: SV: SV: OMAP3 isp single-shot
Daniel Lundborg wrote: Hi Laurent, Hi all, Device /dev/video2 opened: OMAP3 ISP CCDC output (media). Video format set: width: 752 height: 480 buffer size: 721920 Video format: BA10 (30314142) 752x480 1 buffers requested. length: 721920 offset: 0 Buffer 0 mapped at address 0x4014d000. And it freezes. I can stop yavta with CTRL+C. Have you tried to trigger the sensor multiple times in a row ? No. I will test that. Besides the two things what were proposed, it'd be good to check which interrupts does the ISP produce. -- Sakari Ailus sakari.ai...@maxwell.research.nokia.com -- To unsubscribe from this list: send the line unsubscribe linux-media in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
OMAP3 isp single-shot
Hello, I am successfully using the gumstix overo board together with a camera sensor Aptina MT9V034 with the kernel 2.6.35 and patches from http://git.linuxtv.org/pinchartl/media.git (isp6). I can use the media-ctl program and yavta to take pictures in continous streaming mode. media-ctl -r -l 'mt9034 3-0048:0-OMAP3 ISP CCDC:0[1], OMAP3 ISP CCDC:1-OMAP3 ISP CCDC output:0[1]' media-ctl -f 'mt9v034 3-0048:0[SGRBG10 752x480], OMAP3 ISP CCDC:1[SGRBG10 752x480] and then: yavta -f SGRBG10 -s 752x480 -n 1 --capture=1 -F /dev/video2 Is there a way to set the ISP in single shot mode? I have tested setting the mt9v034 in snapshot mode and manually trigger the camera, but the ISP does not send a picture. Is there a way to solve this with the current OMAP3 isp code? I have before successfully used the isp parts from the Nokia N900 project.. /Daniel -- To unsubscribe from this list: send the line unsubscribe linux-media in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
