VC channel configuration is programmed based on settings coming from
the PMIC configuration.
Currently, the VC channel to PMIC mapping is a simple one-to-one
mapping. Whenever a VC channel parameter is configured (i2c slave
addres, PMIC register address, on/ret/off command), the corresponding
bits are enabled in the VC channel configuration register.
If necessary, the programmability of channel configuration settings
could be extended to board/PMIC files, however, because this patch
changes the channel configuration to be programmed based on existing
values from the PMIC settings, it may not be required.
Signed-off-by: Kevin Hilman <khil...@ti.com>
---
arch/arm/mach-omap2/vc.c | 71 ++++++++++++++++++++++++++++++------
arch/arm/mach-omap2/vc.h | 3 ++
arch/arm/mach-omap2/vc3xxx_data.c | 3 ++
arch/arm/mach-omap2/vc44xx_data.c | 4 ++
4 files changed, 69 insertions(+), 12 deletions(-)
diff --git a/arch/arm/mach-omap2/vc.c b/arch/arm/mach-omap2/vc.c
index 4114909..1ce7b24 100644
--- a/arch/arm/mach-omap2/vc.c
+++ b/arch/arm/mach-omap2/vc.c
@@ -10,6 +10,53 @@
#include "prm-regbits-44xx.h"
#include "prm44xx.h"
+/*
+ * Channel configuration bits, common for OMAP3 & 4
+ * OMAP3 register: PRM_VC_CH_CONF
+ * OMAP4 register: PRM_VC_CFG_CHANNEL
+ */
+#define CFG_CHANNEL_SA BIT(0)
+#define CFG_CHANNEL_RAV BIT(1)
+#define CFG_CHANNEL_RAC BIT(2)
+#define CFG_CHANNEL_RACEN BIT(3)
+#define CFG_CHANNEL_CMD BIT(4)
+#define CFG_CHANNEL_MASK 0x3f
+
+/**
+ * omap_vc_config_channel - configure VC channel to PMIC mappings
+ * @voltdm: pointer to voltagdomain defining the desired VC channel
+ *
+ * Configures the VC channel to PMIC mappings for the following
+ * PMIC settings
+ * - i2c slave address (SA)
+ * - voltage configuration address (RAV)
+ * - command configuration address (RAC) and enable bit (RACEN)
+ * - command values for ON, ONLP, RET and OFF (CMD)
+ *
+ * This function currently only allows flexible configuration of
+ * the non-default channel (e.g. non-zero channels.) Starting with
+ * OMAP4, only the non-zero channels can be configured. Channel zero
+ * always uses the channel zero register values. Therefore, the
+ * same limitation is imposed on OMAP3 for consistency.
+ */
+static int omap_vc_config_channel(struct voltagedomain *voltdm)
+{
+ struct omap_vc_channel *vc = voltdm->vc;
+
+ /*
+ * For channel zero, the only configurable bit is RACEN.
+ * All others must stay at zero (see function comment above.)
+ */
+ if (!vc->cfg_channel_sa_shift)
+ vc->cfg_channel &= CFG_CHANNEL_RACEN;
+
+ voltdm->rmw(CFG_CHANNEL_MASK << vc->cfg_channel_sa_shift,
+ vc->cfg_channel << vc->cfg_channel_sa_shift,
+ vc->common->cfg_channel_reg);
+
+ return 0;
+}
+
/* Voltage scale and accessory APIs */
int omap_vc_pre_scale(struct voltagedomain *voltdm,
unsigned long target_volt,
@@ -157,8 +204,6 @@ static void __init omap3_vc_init_channel(struct
voltagedomain *voltdm)
* Generic VC parameters init
* XXX This data should be abstracted out
*/
- voltdm->write(OMAP3430_CMD1_MASK | OMAP3430_RAV1_MASK,
- OMAP3_PRM_VC_CH_CONF_OFFSET);
voltdm->write(OMAP3430_MCODE_SHIFT | OMAP3430_HSEN_MASK,
OMAP3_PRM_VC_I2C_CFG_OFFSET);
@@ -177,15 +222,6 @@ static void __init omap4_vc_init_channel(struct
voltagedomain *voltdm)
if (is_initialized)
return;
- /*
- * Generic VC parameters init
- * XXX This data should be abstracted out
- */
- vc_val = (OMAP4430_RAV_VDD_MPU_L_MASK | OMAP4430_CMD_VDD_MPU_L_MASK |
- OMAP4430_RAV_VDD_IVA_L_MASK | OMAP4430_CMD_VDD_IVA_L_MASK |
- OMAP4430_RAV_VDD_CORE_L_MASK | OMAP4430_CMD_VDD_CORE_L_MASK);
- voltdm->write(vc_val, OMAP4_PRM_VC_CFG_CHANNEL_OFFSET);
-
/* XXX These are magic numbers and do not belong! */
vc_val = (0x60 << OMAP4430_SCLL_SHIFT | 0x26 << OMAP4430_SCLH_SHIFT);
voltdm->write(vc_val, OMAP4_PRM_VC_CFG_I2C_CLK_OFFSET);
@@ -213,6 +249,8 @@ void __init omap_vc_init_channel(struct voltagedomain
*voltdm)
return;
}
+ vc->cfg_channel = 0;
+
/* get PMIC/board specific settings */
vc->i2c_slave_addr = vdd->pmic_info->i2c_slave_addr;
vc->volt_reg_addr = vdd->pmic_info->volt_reg_addr;
@@ -223,6 +261,7 @@ void __init omap_vc_init_channel(struct voltagedomain
*voltdm)
voltdm->rmw(vc->smps_sa_mask,
vc->i2c_slave_addr << __ffs(vc->smps_sa_mask),
vc->common->smps_sa_reg);
+ vc->cfg_channel |= CFG_CHANNEL_SA;
/*
* Configure the PMIC register addresses.
@@ -230,10 +269,14 @@ void __init omap_vc_init_channel(struct voltagedomain
*voltdm)
voltdm->rmw(vc->smps_volra_mask,
vc->volt_reg_addr << __ffs(vc->smps_volra_mask),
vc->common->smps_volra_reg);
- if (vc->cmd_reg_addr)
+ vc->cfg_channel |= CFG_CHANNEL_RAV;
+
+ if (vc->cmd_reg_addr) {
voltdm->rmw(vc->smps_cmdra_mask,
vc->cmd_reg_addr << __ffs(vc->smps_cmdra_mask),
vc->common->smps_cmdra_reg);
+ vc->cfg_channel |= CFG_CHANNEL_RAC | CFG_CHANNEL_RACEN;
+ }
/* Set up the on, inactive, retention and off voltage */
on_vsel = vdd->pmic_info->uv_to_vsel(vdd->pmic_info->on_volt);
@@ -245,6 +288,10 @@ void __init omap_vc_init_channel(struct voltagedomain
*voltdm)
(ret_vsel << vc->common->cmd_ret_shift) |
(off_vsel << vc->common->cmd_off_shift));
voltdm->write(val, vc->cmdval_reg);
+ vc->cfg_channel |= CFG_CHANNEL_CMD;
+
+ /* Channel configuration */
+ omap_vc_config_channel(voltdm);
/* Configure the setup times */
voltdm->rmw(voltdm->vfsm->voltsetup_mask,
diff --git a/arch/arm/mach-omap2/vc.h b/arch/arm/mach-omap2/vc.h
index ade35f7..e0d2931 100644
--- a/arch/arm/mach-omap2/vc.h
+++ b/arch/arm/mach-omap2/vc.h
@@ -53,6 +53,7 @@ struct omap_vc_common {
u8 cmd_onlp_shift;
u8 cmd_ret_shift;
u8 cmd_off_shift;
+ u8 cfg_channel_reg;
};
/**
@@ -66,6 +67,7 @@ struct omap_vc_channel {
u8 i2c_slave_addr;
u8 volt_reg_addr;
u8 cmd_reg_addr;
+ u8 cfg_channel;
u16 setup_time;
/* register access data */
@@ -74,6 +76,7 @@ struct omap_vc_channel {
u32 smps_volra_mask;
u32 smps_cmdra_mask;
u8 cmdval_reg;
+ u8 cfg_channel_sa_shift;
};
extern struct omap_vc_channel omap3_vc_mpu;
diff --git a/arch/arm/mach-omap2/vc3xxx_data.c
b/arch/arm/mach-omap2/vc3xxx_data.c
index df8bd5e..f4449eb 100644
--- a/arch/arm/mach-omap2/vc3xxx_data.c
+++ b/arch/arm/mach-omap2/vc3xxx_data.c
@@ -43,6 +43,7 @@ static struct omap_vc_common omap3_vc_common = {
.cmd_onlp_shift = OMAP3430_VC_CMD_ONLP_SHIFT,
.cmd_ret_shift = OMAP3430_VC_CMD_RET_SHIFT,
.cmd_off_shift = OMAP3430_VC_CMD_OFF_SHIFT,
+ .cfg_channel_reg = OMAP3_PRM_VC_CH_CONF_OFFSET,
};
struct omap_vc_channel omap3_vc_mpu = {
@@ -51,6 +52,7 @@ struct omap_vc_channel omap3_vc_mpu = {
.smps_sa_mask = OMAP3430_PRM_VC_SMPS_SA_SA0_MASK,
.smps_volra_mask = OMAP3430_VOLRA0_MASK,
.smps_cmdra_mask = OMAP3430_CMDRA0_MASK,
+ .cfg_channel_sa_shift = OMAP3430_PRM_VC_SMPS_SA_SA0_SHIFT,
};
struct omap_vc_channel omap3_vc_core = {
@@ -59,4 +61,5 @@ struct omap_vc_channel omap3_vc_core = {
.smps_sa_mask = OMAP3430_PRM_VC_SMPS_SA_SA1_MASK,
.smps_volra_mask = OMAP3430_VOLRA1_MASK,
.smps_cmdra_mask = OMAP3430_CMDRA1_MASK,
+ .cfg_channel_sa_shift = OMAP3430_PRM_VC_SMPS_SA_SA1_SHIFT,
};
diff --git a/arch/arm/mach-omap2/vc44xx_data.c
b/arch/arm/mach-omap2/vc44xx_data.c
index 5d104ff..f933f98 100644
--- a/arch/arm/mach-omap2/vc44xx_data.c
+++ b/arch/arm/mach-omap2/vc44xx_data.c
@@ -44,6 +44,7 @@ static const struct omap_vc_common omap4_vc_common = {
.cmd_onlp_shift = OMAP4430_ONLP_SHIFT,
.cmd_ret_shift = OMAP4430_RET_SHIFT,
.cmd_off_shift = OMAP4430_OFF_SHIFT,
+ .cfg_channel_reg = OMAP4_PRM_VC_CFG_CHANNEL_OFFSET,
};
/* VC instance data for each controllable voltage line */
@@ -53,6 +54,7 @@ struct omap_vc_channel omap4_vc_mpu = {
.smps_sa_mask = OMAP4430_SA_VDD_MPU_L_PRM_VC_SMPS_SA_MASK,
.smps_volra_mask = OMAP4430_VOLRA_VDD_MPU_L_MASK,
.smps_cmdra_mask = OMAP4430_CMDRA_VDD_MPU_L_MASK,
+ .cfg_channel_sa_shift = OMAP4430_SA_VDD_MPU_L_SHIFT,
};
struct omap_vc_channel omap4_vc_iva = {
@@ -61,6 +63,7 @@ struct omap_vc_channel omap4_vc_iva = {
.smps_sa_mask = OMAP4430_SA_VDD_IVA_L_PRM_VC_SMPS_SA_MASK,
.smps_volra_mask = OMAP4430_VOLRA_VDD_IVA_L_MASK,
.smps_cmdra_mask = OMAP4430_CMDRA_VDD_IVA_L_MASK,
+ .cfg_channel_sa_shift = OMAP4430_SA_VDD_IVA_L_SHIFT,
};
struct omap_vc_channel omap4_vc_core = {
@@ -69,5 +72,6 @@ struct omap_vc_channel omap4_vc_core = {
.smps_sa_mask = OMAP4430_SA_VDD_CORE_L_0_6_MASK,
.smps_volra_mask = OMAP4430_VOLRA_VDD_CORE_L_MASK,
.smps_cmdra_mask = OMAP4430_CMDRA_VDD_CORE_L_MASK,
+ .cfg_channel_sa_shift = OMAP4430_SA_VDD_CORE_L_SHIFT,
};
--
1.7.4
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
