Re: tg3: link is permanently down after ifdown and ifup
Hi, Michael Chan wrote: On Thu, 2009-11-19 at 08:08 -0800, Felix Radensky wrote: Hi, The problem goes away if I remove the call to tg3_set_power_state(tp, PCI_D3hot); from tg3_close(). Added Matt to CC. He is on vacation and may not be able to look into this right away. Thanks. Thanks, Michael. After digging some more into it, I've found that the problem is in tg3_power_down_phy() routine. Apparently 57780 PHY is not handled properly. If tg3_power_down_phy() is not invoked from tg3_set_power_state(), the problem is not reproducible anymore. I don't have enough information about NIC internals to dig further. Felix. ___ Linuxppc-dev mailing list Linuxppc-dev@lists.ozlabs.org https://lists.ozlabs.org/listinfo/linuxppc-dev
Re: tg3: link is permanently down after ifdown and ifup
Hi, The problem goes away if I remove the call to tg3_set_power_state(tp, PCI_D3hot); from tg3_close(). Some relevant stuff from dmesg: pci 0002:05:00.0: PME# supported from D3hot D3cold pci 0002:05:00.0: PME# disabled tg3.c:v3.102 (September 1, 2009) tg3 0002:05:00.0: enabling device ( - 0002) tg3 0002:05:00.0: PME# disabled tg3 mdio bus: probed eth2: Tigon3 [partno(BCM57760) rev 57780001] (PCI Express) MAC address 00:10:18:00:00:00 eth2: attached PHY driver [Broadcom BCM57780] (mii_bus:phy_addr=500:01) eth2: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] eth2: dma_rwctrl[7618] dma_mask[64-bit] Is my problem related to hardware or it's a tg3 driver bug ? Thanks a lot. Felix. Felix Radensky wrote: Hi, I have a problem with tg3 driver on a custom MPC8536 based board running linux-2.6.31, with tg3 and Broadcom phy drivers taken from linux-2.6.32-rc7. Broadcom NIC is BCM57760, phy is BCM57780. The problem I'm seeing is that the downing and interface leads to permanent link loss, even after interface is upped again. E.g, to reproduce the problem it is sufficient to run: modprobe tg3 ifconfig eth2 up ifconfig eth2 down ifconfig eth2 up After ifdown PHY LEDs also go down and do not come back after ifup. Ethtool reports that no link is detected. After reloading the driver the link comes back. Am I the only one seeing this problem ? Any help on fixing this is appreciated. Thanks a lot. Felix. ___ Linuxppc-dev mailing list Linuxppc-dev@lists.ozlabs.org https://lists.ozlabs.org/listinfo/linuxppc-dev ___ Linuxppc-dev mailing list Linuxppc-dev@lists.ozlabs.org https://lists.ozlabs.org/listinfo/linuxppc-dev
Re: tg3: link is permanently down after ifdown and ifup
On Thu, 2009-11-19 at 08:08 -0800, Felix Radensky wrote: Hi, The problem goes away if I remove the call to tg3_set_power_state(tp, PCI_D3hot); from tg3_close(). Added Matt to CC. He is on vacation and may not be able to look into this right away. Thanks. ___ Linuxppc-dev mailing list Linuxppc-dev@lists.ozlabs.org https://lists.ozlabs.org/listinfo/linuxppc-dev