Good evening, all,
Recently upgraded my ERL to a snapshot (5/10/18) to test out the octcrypto
module that visa recently enabled. Install went as smoothly as can be
expected, upon reboot I saw the octcrypto module load,and everything
seems to be working great. I haven't had a chance to test out the module
yet, but I will let the list know when I get to it.
Also, I managed to get the install kernel to recognize that this is a multiproc
machine by using "bootoctlinux $loadaddr bsd coremask=0x3" as my
boot command after the install kernel was loaded via tftpboot. Excellent
work and thanks to everyone, dmesg to follow:
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2018 OpenBSD. All rights reserved. https://www.OpenBSD.org
OpenBSD 6.3-current (GENERIC.MP) #0: Wed May 9 07:17:26 UTC 2018
visa@octeon:/usr/src/sys/arch/octeon/compile/GENERIC.MP
real mem = 536870912 (512MB)
avail mem = 523845632 (499MB)
mainbus0 at root: board 20002 rev 2.18
cpu0 at mainbus0: CN50xx CPU rev 0.1 500 MHz, Software FP emulation
cpu0: cache L1-I 32KB 4 way D 16KB 64 way, L2 128KB 8 way
cpu1 at mainbus0: CN50xx CPU rev 0.1 500 MHz, Software FP emulation
cpu1: cache L1-I 32KB 4 way D 16KB 64 way, L2 128KB 8 way
clock0 at mainbus0: int 5
octcrypto0 at mainbus0
iobus0 at mainbus0
simplebus0 at iobus0: "soc"
octciu0 at simplebus0
cn30xxsmi0 at simplebus0
com0 at simplebus0: ns16550a, 64 byte fifo
com0: console
dwctwo0 at iobus0 base 0x1180068000000 irq 56
usb0 at dwctwo0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Octeon DWC2 root hub" rev
2.00/1.00 addr 1
octrng0 at iobus0 base 0x1400000000000 irq 0
cn30xxgmx0 at iobus0 base 0x1180008000000
cnmac0 at cn30xxgmx0: RGMII, address 44:d9:e7:40:b5:c8
atphy0 at cnmac0 phy 7: AR8035 10/100/1000 PHY, rev. 2
cnmac1 at cn30xxgmx0: RGMII, address 44:d9:e7:40:b5:c9
atphy1 at cnmac1 phy 6: AR8035 10/100/1000 PHY, rev. 2
cnmac2 at cn30xxgmx0: RGMII, address 44:d9:e7:40:b5:ca
atphy2 at cnmac2 phy 5: AR8035 10/100/1000 PHY, rev. 2
/dev/ksyms: Symbol table not valid.
umass0 at uhub0 port 1 configuration 1 interface 0 "Lexar USB Flash
Drive" rev 2.10/11.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <Lexar, USB Flash Drive, 1100> SCSI4
0/direct removable serial.05dca83aZB0L2W63LA4P
sd0: 30526MB, 512 bytes/sector, 62517248 sectors
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
boot device: sd0
root on sd0a (fb74a192b03ee90f.a) swap on sd0b dump on sd0b
