Switch over to using a module parameter and debug prints
that can be controlled by this or ethtool like everyone
else. Depromote all other prints to debug messages.
The phy_print_status() was already in place, albeit never
really used because the debuglevel hiding it had to be
set up using ethtool.
Signed-off-by: Linus Walleij
---
ChangeLog v2->v3:
- Use phy_attached_info() live all other drivers.
- Put it in an if (netif_msg_link()) clause like the
other message from phy_print_status().
- Explain more in the commit message.
ChangeLog v1->v2:
- Use a module parameter and the message levels like all
other drivers and stop trying to be special.
---
drivers/net/ethernet/cortina/gemini.c | 46 +++
1 file changed, 26 insertions(+), 20 deletions(-)
diff --git a/drivers/net/ethernet/cortina/gemini.c
b/drivers/net/ethernet/cortina/gemini.c
index 8fc31723f700..f0ab6426daca 100644
--- a/drivers/net/ethernet/cortina/gemini.c
+++ b/drivers/net/ethernet/cortina/gemini.c
@@ -46,6 +46,11 @@
#define DRV_NAME "gmac-gemini"
#define DRV_VERSION"1.0"
+#define DEFAULT_MSG_ENABLE (NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK)
+static int debug = -1;
+module_param(debug, int, 0);
+MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
+
#define HSIZE_80x00
#define HSIZE_16 0x01
#define HSIZE_32 0x02
@@ -300,23 +305,26 @@ static void gmac_speed_set(struct net_device *netdev)
status.bits.speed = GMAC_SPEED_1000;
if (phydev->interface == PHY_INTERFACE_MODE_RGMII)
status.bits.mii_rmii = GMAC_PHY_RGMII_1000;
- netdev_info(netdev, "connect to RGMII @ 1Gbit\n");
+ netdev_dbg(netdev, "connect %s to RGMII @ 1Gbit\n",
+ phydev_name(phydev));
break;
case 100:
status.bits.speed = GMAC_SPEED_100;
if (phydev->interface == PHY_INTERFACE_MODE_RGMII)
status.bits.mii_rmii = GMAC_PHY_RGMII_100_10;
- netdev_info(netdev, "connect to RGMII @ 100 Mbit\n");
+ netdev_dbg(netdev, "connect %s to RGMII @ 100 Mbit\n",
+ phydev_name(phydev));
break;
case 10:
status.bits.speed = GMAC_SPEED_10;
if (phydev->interface == PHY_INTERFACE_MODE_RGMII)
status.bits.mii_rmii = GMAC_PHY_RGMII_100_10;
- netdev_info(netdev, "connect to RGMII @ 10 Mbit\n");
+ netdev_dbg(netdev, "connect %s to RGMII @ 10 Mbit\n",
+ phydev_name(phydev));
break;
default:
- netdev_warn(netdev, "Not supported PHY speed (%d)\n",
- phydev->speed);
+ netdev_warn(netdev, "Unsupported PHY speed (%d) on %s\n",
+ phydev->speed, phydev_name(phydev));
}
if (phydev->duplex == DUPLEX_FULL) {
@@ -363,12 +371,6 @@ static int gmac_setup_phy(struct net_device *netdev)
return -ENODEV;
netdev->phydev = phy;
- netdev_info(netdev, "connected to PHY \"%s\"\n",
- phydev_name(phy));
- phy_attached_print(phy, "phy_id=0x%.8lx, phy_mode=%s\n",
- (unsigned long)phy->phy_id,
- phy_modes(phy->interface));
-
phy->supported &= PHY_GBIT_FEATURES;
phy->supported |= SUPPORTED_Asym_Pause | SUPPORTED_Pause;
phy->advertising = phy->supported;
@@ -376,19 +378,19 @@ static int gmac_setup_phy(struct net_device *netdev)
/* set PHY interface type */
switch (phy->interface) {
case PHY_INTERFACE_MODE_MII:
- netdev_info(netdev, "set GMAC0 to GMII mode, GMAC1 disabled\n");
+ netdev_dbg(netdev,
+ "MII: set GMAC0 to GMII mode, GMAC1 disabled\n");
status.bits.mii_rmii = GMAC_PHY_MII;
- netdev_info(netdev, "connect to MII\n");
break;
case PHY_INTERFACE_MODE_GMII:
- netdev_info(netdev, "set GMAC0 to GMII mode, GMAC1 disabled\n");
+ netdev_dbg(netdev,
+ "GMII: set GMAC0 to GMII mode, GMAC1 disabled\n");
status.bits.mii_rmii = GMAC_PHY_GMII;
- netdev_info(netdev, "connect to GMII\n");
break;
case PHY_INTERFACE_MODE_RGMII:
- dev_info(dev, "set GMAC0 and GMAC1 to MII/RGMII mode\n");
+ netdev_dbg(netdev,
+ "RGMII: set GMAC0 and GMAC1 to MII/RGMII mode\n");
status.bits.mii_rmii = GMAC_PHY_RGMII_100_10;
- netdev_info(netdev, "connect to RGMII\n");
break;
default:
netdev_err(netdev, "Unsupported MII interface\n");
@@ -398,6 +400,9 @@ static int
