RE: [PATCHv8] wlcore: spi: add wl18xx support

[Reizer, Eyal]

> 
> > Add support for using with both wl12xx and wl18xx.
> >
> > - all wilink family needs special init command for entering wspi mode.
> >   extra clock cycles should be sent after the spi init command while the
> >   cs pin is high.
> > - Use inverted chip select for sending a dummy 4 bytes command that
> >   completes the init stage.
> >
> > Signed-off-by: Eyal Reizer 
> > Acked-by: Rob Herring 
> > ---
> > v1->v2:update device tree bindings configuration
> > v2->v3:revert from manual gpio manipulation. use inverted chip select
> instead
> > for sending the extra init cycle which, achieves the same hardware purpose.
> > update device tree bindings docucmentation accordingly
> > v3->v4: Remove redundant data form binding documentation and fix chip
> select
> > number mismatch in wl1271 example
> > v4->v5: Rebase on top of head of wireless-drivers-next
> > v5->v6: Add ACKs
> > v6->v7: Mail format issues
> > v7->v8: Remove redundant varaible from wlcore_probe_of
> 
> I have already applied this patch, it's too late to send a new version.
> Now you need to send a new patch, on top of wireless-drivers-next, which
> removes the redundant variable.
> 
Understood. Will submit shortly

Best Regards,
Eyal

Re: [PATCHv8] wlcore: spi: add wl18xx support

[Kalle Valo]

"Reizer, Eyal"  writes:

> Add support for using with both wl12xx and wl18xx.
>
> - all wilink family needs special init command for entering wspi mode.
>   extra clock cycles should be sent after the spi init command while the
>   cs pin is high.
> - Use inverted chip select for sending a dummy 4 bytes command that
>   completes the init stage.
>
> Signed-off-by: Eyal Reizer 
> Acked-by: Rob Herring 
> ---
> v1->v2:update device tree bindings configuration
> v2->v3:revert from manual gpio manipulation. use inverted chip select instead
> for sending the extra init cycle which, achieves the same hardware purpose.
> update device tree bindings docucmentation accordingly
> v3->v4: Remove redundant data form binding documentation and fix chip select
> number mismatch in wl1271 example
> v4->v5: Rebase on top of head of wireless-drivers-next
> v5->v6: Add ACKs
> v6->v7: Mail format issues
> v7->v8: Remove redundant varaible from wlcore_probe_of

I have already applied this patch, it's too late to send a new version.
Now you need to send a new patch, on top of wireless-drivers-next, which
removes the redundant variable.

-- 
Kalle Valo

[PATCHv8] wlcore: spi: add wl18xx support

[Reizer, Eyal]

Add support for using with both wl12xx and wl18xx.

- all wilink family needs special init command for entering wspi mode.
  extra clock cycles should be sent after the spi init command while the
  cs pin is high.
- Use inverted chip select for sending a dummy 4 bytes command that
  completes the init stage.

Signed-off-by: Eyal Reizer 
Acked-by: Rob Herring 
---
v1->v2:update device tree bindings configuration
v2->v3:revert from manual gpio manipulation. use inverted chip select instead
for sending the extra init cycle which, achieves the same hardware purpose.
update device tree bindings docucmentation accordingly
v3->v4: Remove redundant data form binding documentation and fix chip select
number mismatch in wl1271 example
v4->v5: Rebase on top of head of wireless-drivers-next
v5->v6: Add ACKs
v6->v7: Mail format issues
v7->v8: Remove redundant varaible from wlcore_probe_of
 .../bindings/net/wireless/ti,wlcore,spi.txt|  41 +--
 drivers/net/wireless/ti/wlcore/spi.c   | 124 +
 2 files changed, 137 insertions(+), 28 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt 
b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt
index 9180724..8f9ced0 100644
--- a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt
+++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt
@@ -1,19 +1,30 @@
-* Texas Instruments wl1271 wireless lan controller
+* Texas Instruments wl12xx/wl18xx wireless lan controller
 
-The wl1271 chip can be connected via SPI or via SDIO. This
+The wl12xx/wl18xx chips can be connected via SPI or via SDIO. This
 document describes the binding for the SPI connected chip.
 
 Required properties:
-- compatible :  Should be "ti,wl1271"
+- compatible :  Should be one of the following:
+* "ti,wl1271"
+* "ti,wl1273"
+* "ti,wl1281"
+* "ti,wl1283"
+* "ti,wl1801"
+* "ti,wl1805"
+* "ti,wl1807"
+* "ti,wl1831"
+* "ti,wl1835"
+* "ti,wl1837"
 - reg : Chip select address of device
 - spi-max-frequency :   Maximum SPI clocking speed of device in Hz
-- ref-clock-frequency : Reference clock frequency
 - interrupt-parent, interrupts :
 Should contain parameters for 1 interrupt line.
 Interrupt parameters: parent, line number, type.
-- vwlan-supply :Point the node of the regulator that powers/enable the 
wl1271 chip
+- vwlan-supply :Point the node of the regulator that powers/enable the
+wl12xx/wl18xx chip
 
 Optional properties:
+- ref-clock-frequency : Reference clock frequency (should be set for wl12xx)
 - clock-xtal :  boolean, clock is generated from XTAL
 
 - Please consult Documentation/devicetree/bindings/spi/spi-bus.txt
@@ -21,16 +32,28 @@ Optional properties:
 
 Examples:
 
+For wl12xx family:
  {
-   wl1271@1 {
+   wlcore: wlcore@1 {
compatible = "ti,wl1271";
-
reg = <1>;
spi-max-frequency = <4800>;
-   clock-xtal;
-   ref-clock-frequency = <3840>;
interrupt-parent = <>;
interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
vwlan-supply = <_fixed>;
+   clock-xtal;
+   ref-clock-frequency = <3840>;
+   };
+};
+
+For wl18xx family:
+ {
+   wlcore: wlcore@0 {
+   compatible = "ti,wl1835";
+   reg = <0>;
+   spi-max-frequency = <4800>;
+   interrupt-parent = <>;
+   interrupts = <27 IRQ_TYPE_EDGE_RISING>;
+   vwlan-supply = <_fixed>;
};
 };
diff --git a/drivers/net/wireless/ti/wlcore/spi.c 
b/drivers/net/wireless/ti/wlcore/spi.c
index cea9443..6d24040 100644
--- a/drivers/net/wireless/ti/wlcore/spi.c
+++ b/drivers/net/wireless/ti/wlcore/spi.c
@@ -70,16 +70,30 @@
 #define WSPI_MAX_CHUNK_SIZE4092
 
 /*
- * only support SPI for 12xx - this code should be reworked when 18xx
- * support is introduced
+ * wl18xx driver aggregation buffer size is (13 * PAGE_SIZE) compared to
+ * (4 * PAGE_SIZE) for wl12xx, so use the larger buffer needed for wl18xx
  */
-#define SPI_AGGR_BUFFER_SIZE (4 * PAGE_SIZE)
+#define SPI_AGGR_BUFFER_SIZE (13 * PAGE_SIZE)
 
 /* Maximum number of SPI write chunks */
 #define WSPI_MAX_NUM_OF_CHUNKS \
((SPI_AGGR_BUFFER_SIZE / WSPI_MAX_CHUNK_SIZE) + 1)
 
 
+struct wilink_familiy_data {
+   char name[8];
+};
+
+const struct wilink_familiy_data *wilink_data;
+
+static const struct wilink_familiy_data wl18xx_data = {
+   .name = "wl18xx",
+};
+
+static const struct wilink_familiy_data wl12xx_data = {
+   .name = "wl12xx",
+};
+
 struct wl12xx_spi_glue {
struct device *dev;
struct platform_device *core;
@@ -119,6 +133,7 @@ static void wl12xx_spi_init(struct device *child)
struct wl12xx_spi_glue *glue =