SOC: Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM: 64MB Zentel A3R12E40CBF DDR2
FLASH: 16MiB Winbond W25Q128 SPI NOR
WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT: WPS button
LED: Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes.
You need to powercycle the device afterwards to boot OpenWRT.
Tested-by: Andreas Ziegler <d...@andreas-ziegler.de>
Signed-off-by: David Bauer <m...@david-bauer.net>
---
.../ath79/dts/qca9556_avm_fritz-repeater.dtsi | 93 +++++++++++++++++++
.../ath79/dts/qca9556_avm_fritz1750e.dts | 89 +-----------------
.../linux/ath79/dts/qca9556_avm_fritz450e.dts | 76 +++++++++++++++
.../generic/base-files/etc/board.d/01_leds | 3 +-
.../generic/base-files/etc/board.d/02_network | 3 +-
.../etc/hotplug.d/firmware/10-ath9k-eeprom | 3 +-
.../base-files/lib/preinit/10_fix_eth_mac.sh | 3 +-
target/linux/ath79/image/generic.mk | 9 ++
8 files changed, 189 insertions(+), 90 deletions(-)
create mode 100644 target/linux/ath79/dts/qca9556_avm_fritz-repeater.dtsi
create mode 100644 target/linux/ath79/dts/qca9556_avm_fritz450e.dts
diff --git a/target/linux/ath79/dts/qca9556_avm_fritz-repeater.dtsi
b/target/linux/ath79/dts/qca9556_avm_fritz-repeater.dtsi
new file mode 100644
index 0000000000..b1f5f1bdb3
--- /dev/null
+++ b/target/linux/ath79/dts/qca9556_avm_fritz-repeater.dtsi
@@ -0,0 +1,93 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca9557.dtsi"
+
+/ {
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&uart {
+ status = "okay";
+};
+
+&spi {
+ status = "okay";
+ num-cs = <1>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "urlader";
+ reg = <0x0 0x20000>;
+ read-only;
+ };
+
+ partition@20000 {
+ compatible = "avm,eva-firmware";
+ label = "firmware";
+ reg = <0x20000 0xee0000>;
+ };
+
+ partition@f00000 {
+ label = "tffs (1)";
+ reg = <0xf00000 0x80000>;
+ read-only;
+ };
+
+ partition@f80000 {
+ label = "tffs (2)";
+ reg = <0xf80000 0x80000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&wmac {
+ status = "okay";
+ qca,no-eeprom;
+};
+
+ð1 {
+ status = "okay";
+
+ phy-handle = <&phy0>;
+ pll-data = <0x3000000 0x101 0x1313>;
+
+ gmac-config {
+ device = <&gmac>;
+ ge0-sgmii = <0>;
+ };
+};
+
+&mdio1 {
+ status = "okay";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
diff --git a/target/linux/ath79/dts/qca9556_avm_fritz1750e.dts
b/target/linux/ath79/dts/qca9556_avm_fritz1750e.dts
index f50af5b228..25d3ae8da4 100644
--- a/target/linux/ath79/dts/qca9556_avm_fritz1750e.dts
+++ b/target/linux/ath79/dts/qca9556_avm_fritz1750e.dts
@@ -1,19 +1,13 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include "qca9557.dtsi"
+#include "qca9556_avm_fritz-repeater.dtsi"
/ {
compatible = "avm,fritz1750e", "qca,qca9557";
model = "AVM FRITZ!WLAN Repeater 1750E";
- chosen {
- bootargs = "console=ttyS0,115200n8";
- };
-
aliases {
led-boot = &led_power;
led-failsafe = &led_power;
@@ -91,65 +85,14 @@
gpios = <&spi_gpio 4 GPIO_ACTIVE_HIGH>;
};
};
-
- keys {
- compatible = "gpio-keys";
-
- wps {
- label = "wps";
- linux,code = <KEY_WPS_BUTTON>;
- gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
- };
- };
};
&pcie0 {
status = "okay";
};
-&uart {
- status = "okay";
-};
-
-&spi {
- status = "okay";
- num-cs = <1>;
-
- flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <25000000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "urlader";
- reg = <0x0 0x20000>;
- read-only;
- };
-
- partition@20000 {
- compatible = "avm,eva-firmware";
- label = "firmware";
- reg = <0x20000 0xee0000>;
- };
-
- partition@f00000 {
- label = "tffs (1)";
- reg = <0xf00000 0x80000>;
- read-only;
- };
-
- partition@f80000 {
- label = "tffs (2)";
- reg = <0xf80000 0x80000>;
- read-only;
- };
- };
- };
+&phy0 {
+ reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
};
&gpio {
@@ -167,29 +110,3 @@
line-name = "PCIE Bus reset";
};
};
-
-&wmac {
- status = "okay";
- qca,no-eeprom;
-};
-
-ð1 {
- status = "okay";
-
- phy-handle = <&phy0>;
- pll-data = <0x3000000 0x101 0x1313>;
-
- gmac-config {
- device = <&gmac>;
- ge0-sgmii = <0>;
- };
-};
-
-&mdio1 {
- status = "okay";
-
- phy0: ethernet-phy@0 {
- reg = <0>;
- reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
- };
-};
diff --git a/target/linux/ath79/dts/qca9556_avm_fritz450e.dts
b/target/linux/ath79/dts/qca9556_avm_fritz450e.dts
new file mode 100644
index 0000000000..60685bd3f1
--- /dev/null
+++ b/target/linux/ath79/dts/qca9556_avm_fritz450e.dts
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/gpio/gpio.h>
+
+#include "qca9556_avm_fritz-repeater.dtsi"
+
+/ {
+ compatible = "avm,fritz450e", "qca,qca9557";
+ model = "AVM FRITZ!WLAN Repeater 450E";
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "fritz450e:green:power";
+ gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan {
+ label = "fritz450e:green:wlan";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ lan {
+ label = "fritz450e:green:lan";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ rssi2 {
+ label = "fritz450e:green:rssi2";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ };
+
+ rssi3 {
+ label = "fritz450e:green:rssi3";
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ };
+
+ rssi4 {
+ label = "fritz450e:green:rssi4";
+ gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&gpio {
+ /*
+ * Wondered why rssi0 and rssi1 are missing?
+ *
+ * AVM seems to have run low on usable GPIO pins, so
+ * instead of adding a shift register like they did for
+ * the 1750E they figured out "Why not use the LEDs on
+ * the AR8033?".
+ *
+ * EVA configures the PHY in a way it does not display
+ * the link-state using it's LEDs. When we reset the PHY
+ * using the reset-mechanism of the PHY subsystem, this
+ * setting is cleared.
+ *
+ * We avoid this by keeping the reset line high.
+ */
+ phy-reset {
+ gpio-hog;
+ gpios = <11 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "phy-reset";
+ };
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index b57f4cdd8e..ca4bb3dd33 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -12,7 +12,8 @@ case "$board" in
ucidef_set_led_netdev "lan" "LAN" "$boardname:orange:eth0" "eth0"
ucidef_set_led_switch "wan" "WAN" "$boardname:orange:eth1" "switch0"
"0x04"
;;
-alfa-network,ap121f)
+alfa-network,ap121f|\
+avm,fritz450e)
ucidef_set_led_netdev "lan" "LAN" "$boardname:green:lan" "eth0"
;;
avm,fritz1750e)
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network
b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index 96800d771f..543543ad54 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -338,7 +338,8 @@ ath79_setup_macs()
alfa-network,ap121f)
label_mac=$(mtd_get_mac_binary art 0x1002)
;;
- avm,fritz1750e)
+ avm,fritz1750e|\
+ avm,fritz450e)
label_mac=$(fritz_tffs -n macwlan -i $(find_mtd_part "tffs
(1)"))
;;
avm,fritz300e)
diff --git
a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index 782e003911..428b502d81 100644
---
a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++
b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -10,7 +10,8 @@ case "$FIRMWARE" in
"ath9k-eeprom-ahb-18100000.wmac.bin")
case $board in
avm,fritz1750e|\
- avm,fritz4020)
+ avm,fritz4020|\
+ avm,fritz450e)
caldata_extract_reverse "urlader" 0x1541 0x440
;;
dlink,dir-505|\
diff --git
a/target/linux/ath79/generic/base-files/lib/preinit/10_fix_eth_mac.sh
b/target/linux/ath79/generic/base-files/lib/preinit/10_fix_eth_mac.sh
index 371efd6a83..b3c3de298e 100644
--- a/target/linux/ath79/generic/base-files/lib/preinit/10_fix_eth_mac.sh
+++ b/target/linux/ath79/generic/base-files/lib/preinit/10_fix_eth_mac.sh
@@ -4,7 +4,8 @@
preinit_set_mac_address() {
case $(board_name) in
- avm,fritz1750e)
+ avm,fritz1750e|\
+ avm,fritz450e)
ip link set dev eth0 address $(fritz_tffs -n maca -i
$(find_mtd_part "tffs (1)"))
;;
siemens,ws-ap3610)
diff --git a/target/linux/ath79/image/generic.mk
b/target/linux/ath79/image/generic.mk
index 3acbeb2859..b449832ad2 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -201,6 +201,15 @@ define Device/avm_fritz4020
endef
TARGET_DEVICES += avm_fritz4020
+define Device/avm_fritz450e
+ $(Device/avm)
+ SOC := qca9556
+ IMAGE_SIZE := 15232k
+ DEVICE_MODEL := FRITZ!WLAN Repeater 450E
+ SUPPORTED_DEVICES += fritz450e
+endef
+TARGET_DEVICES += avm_fritz450e
+
define Device/buffalo_bhr-4grv
SOC := ar7242
DEVICE_VENDOR := Buffalo
--
2.26.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
