Its on my to-do list to update it.
Best regards,
Jordan
-Original Message-
From: Jermaine Kendall
Sent: Friday, June 25, 2021 11:46 PM
To: users@cloudstack.apache.org
Subject: Re: RE: XCP-NG 8.2 LTS
[X] This message came from outside your organization
Thank you for the reply. It is very much appreciated. Can the documentation be
upgraded for XCP-NG hypervisor setup and let me know it's done
On 2021/06/25 20:33:08, Yordan Kostov wrote:
> Hello Jermaine,
>
> Long story short:
> 1. Install XCP-NG 8.2
> 1.1. Make a a note of the name of the interface OR bond that is
> going to be used for management traffic (this can be seen when you go to
> CLUSTER -> networking tab
> 1.2. Make a note of the name of the interface OR bond that is
> going to be used for user/public traffic if it is different then the
> management
> For example I use ETH0 for management and have bonded eth2 and eth3 and
> use that bond for Public and user traffic -
> https://urldefense.com/v3/__https://imgur.com/nbV2aAu__;!!A6UyJA!wDUMW6z5oiy9Dn5sjnQg0lEHza62apzb8T-x4oNAB42Sh99wLL6e3w9RjmN59FNHoLQ2vcyqdMZ2$
> So the labels here are MGMT and DATA.
> 2. If you use presetup storage (for example fiber) attach it as you
> usually do to the XCP cluster and note the name of the LUN in XenCenter.
> 3. Install Cloudstack somewhere (4.15) and deploy a zone by filling up
> the guide from start to end using the interface labels and the LUN name for
> primary storage.
> 4. Launch the zone deployment and wait for it to fail.
> 5. Cancel the wizard and go to Infrastruture tab. You will see that
> Zone, Pod, cluster and hosts are deployed.
> 6. select primary storage tab. Add new one with presetup type and fill
> in the storage LUN name. It will be added properly.
> 7. Deploy secondary storage (it was not deployed initially
> because the zone wizard was interrupted before that step)
>
> You environment is now ready!
>
> Note: the deployment guide should be edited as it says XenServer switch
> needs to be in bridge mode in order the system to work which is not correct
> as ACS fully supports OVS.
> May be bridge mode is required for some specific network design setting
> which I am not aware of at the moment.
>
> Best regards,
> Jordan
>
>
> -Original Message-
> From: Jermaine Kendall
> Sent: Friday, June 25, 2021 10:49 PM
> To: users@cloudstack.apache.org
> Subject: Re: XCP-NG 8.2 LTS
>
>
> [X] This message came from outside your organization
>
>
> On 2021/05/05 09:50:58, Andrija Panic wrote:
> > If you use officially unsupported hypevisor with 4.14 (XCP-ng 8.2),
> > you will be missing the records in the guest_os_hypervisor table,
> > and that means your VMs would be i.e. started as PV instead of HVM etc.
> >
> > Be warned :)
> >
> > Best,
> > Andrija
> >
> > On Wed, 5 May 2021 at 09:09, Yordan Kostov wrote:
> >
> > > One more problem is that if you deploy a zone with presetup
> > > storage it will give an error when it is at the step when the storage is
> > > configured.
> > > It is already fixed in 4.15.1:
> > >
> > > https://urldefense.com/v3/__https://github.com/apache/cloudstack/p
> > > ul
> > > l/4845__;!!A6UyJA!xbgZNCFeV-go7cGrUjQ---_MlaAER2Fdumg-cMdW4msQVKLQ
> > > Oh
> > > yt15t8yi-mQoUBNEaGjZ6RgICA$
> > >
> > > Best regards,
> > > Jordan
> > >
> > > -Original Message-
> > > From: Dominik Czerepiński
> > > Sent: Tuesday, May 4, 2021 3:06 PM
> > > To: users@cloudstack.apache.org
> > > Subject: Re: XCP-NG 8.2 LTS
> > >
> > >
> > > [X] This message came from outside your organization
> > >
> > >
> > > Me. Works stable. One problem is if You don’t use SSL for
> > > consoleproxy change noVNC to older version.
> > >
> > > Wysłane z iPhone'a
> > >
> > > > Wiadomość napisana przez Matheus Fontes w
> > > > dniu
> > > 04.05.2021, o godz. 03:18:
> > > >
> > > > I saw in cloudstack 4.15 documentation that it supports xcp-ng
> > > > 8.1 Does someone tried 8.2 LTS version?
> > > >
> > > > thanks
> > > > Matheus Fontes
> > >
> >
> >
> > --
> >
> > Andrija Panić
> > Hi, I have a few questions with regard to setting up xcp-ng with
> > cloudstack, I have never been successful so far. I followed the xenserver
> > hypervisor setup and ran into some issues. Do you have any instructions
> > specifically for setting up XCP-NG with cloudstack? Also is the CSP package
> > needed for XCP-NG becuase the download link is no longer available. The
> > network labels, are they necessary and why can't I use the default
> > networking for XCP-NG which is OVS?
>