Re: [ClusterLabs] normal reboot with active sbd does not work
This change in 'watchdog.service' resolves the reboot problem. Thanks. --- [Unit] Before=sbd.service [Install] RequiredBy=sbd.service --- Zoran - Original Message - From: "Klaus Wenninger" To: "users" Sent: Friday, June 3, 2022 4:35:49 PM Subject: Re: [ClusterLabs] normal reboot with active sbd does not work On Fri, Jun 3, 2022 at 3:51 PM Zoran Bošnjak wrote: > > Thanks for all your answers. Sorry, my mistake. The ipmi_watchdog is indeed > OK. I was first experimenting with "softdog", which is blacklisted. So the > reasonable question is how to properly start "softdog" on ubuntu. > > The reason to unload watchdog module (ipmi or softdog) is that there seems to > be a difference between normal reboot and watchdog reboot. > In case of ipmi watchdog timer reboot: > - the system hangs at the end of reboot cycle for some time > - restart seems to be harder (like power off/on cycle), BIOS runs more > diagnostics at startup > - it turns on HW diagnostic indication on the server front panel (dell > server) which stays on forever > - it logs the event to IDRAC, which is unnecessary, because it was not a > hardware event, but just a normal reboot > > In case of "sudo reboot" command, I would like to skip this... so the idea is > to fully stop the watchdog just before reboot. I am not sure how to do this > properly. > > The "softdog" is better in this respect. It does not trigger nothing from the > list above, but I still get the message during reboot > [ ... ] watchdog: watchdog0: watchdog did not stop! > ... with some small timeout. > > So after some additional testing, the situation is the following: > > - without any watchdog and without sbd package, the server reboots normally > - with "softdog" module loaded, I only get "watchdog did not stop message" at > reboot > - with "softdog" loaded, but unloaded with "ExecStop=...rmmod", reboot is > normal again > - same as above, but with "sbd" package loaded, I am getting "watchdog did > not stop message" again > - switching from "softdog" to "ipmi_watchdog" gets me to the original list of > problems > > It looks like the "sbd" is preventing the watchdog to close, so that watchdog > triggers always, even in the case of normal reboot. What am I missing here? sbd has the watchdog-device open and thus is preventing unloading the module. Without giving any instructions in your unit-file systemd will try to stop the unit immediately and thus fail. Have you tried [Unit] Before=sbd.service [Install] RequiredBy=sbd.service I would have expected that rebooting with the device disabled again after sbd shuts down should behave similarly as with the module being unloaded. You could check for something like 'nowayout' with the kernel module that would prevent disabling the watchdog once opened. Klaus > > Zoran > > - Original Message - > From: "Andrei Borzenkov" > To: "users" > Sent: Friday, June 3, 2022 11:24:03 AM > Subject: Re: [ClusterLabs] normal reboot with active sbd does not work > > On 03.06.2022 11:18, Zoran Bošnjak wrote: > > Hi all, > > I would appreciate an advice about sbd fencing (without shared storage). > > > > I am using ubuntu 20.04., with default packages from the repository > > (pacemaker, corosync, fence-agents, ipmitool, pcs...). > > > > HW watchdog is present on servers. The first problem was to load/unload the > > watchdog module. For some reason the module is blacklisted on ubuntu, > > What makes you think so? > > bor@bor-Latitude-E5450:~$ lsb_release -d > > Description:Ubuntu 20.04.4 LTS > > bor@bor-Latitude-E5450:~$ modprobe -c | grep ipmi_watchdog > > bor@bor-Latitude-E5450:~$ > > > > > > > so I've created a service for this purpose. > > > > man modules-load.d > > > > --- file: /etc/systemd/system/watchdog.service > > [Unit] > > Description=Load watchdog timer module > > After=syslog.target > > > > Without any explicit dependencies stop will be attempted as soon as > possible. > > > [Service] > > Type=oneshot > > RemainAfterExit=yes > > ExecStart=/sbin/modprobe ipmi_watchdog > > ExecStop=/sbin/rmmod ipmi_watchdog > > > > Why on earth do you need to unload kernel driver when system reboots? > > > [Install] > > WantedBy=multi-user.target > > --- > > > > Is this a proper way to load watchdog module under ubuntu? > > > > There is standard way to load non-autoloaded drivers on *any* systemd > based distribution. Whi
Re: [ClusterLabs] normal reboot with active sbd does not work
On 03.06.2022 16:51, Zoran Bošnjak wrote: > Thanks for all your answers. Sorry, my mistake. The ipmi_watchdog is indeed > OK. I was first experimenting with "softdog", which is blacklisted. So the > reasonable question is how to properly start "softdog" on ubuntu. > blacklist prevents autoloading of modules by alias during hardware detection. Neither softdog or ipmi_watchdog have any alias so they cannot be autoloaded and blacklist is irrelevant here. > The reason to unload watchdog module (ipmi or softdog) is that there seems to > be a difference between normal reboot and watchdog reboot. > In case of ipmi watchdog timer reboot: > - the system hangs at the end of reboot cycle for some time > - restart seems to be harder (like power off/on cycle), BIOS runs more > diagnostics at startup > - it turns on HW diagnostic indication on the server front panel (dell > server) which stays on forever > - it logs the event to IDRAC, which is unnecessary, because it was not a > hardware event, but just a normal reboot > > In case of "sudo reboot" command, I would like to skip this... so the idea is > to fully stop the watchdog just before reboot. I am not sure how to do this > properly. > > The "softdog" is better in this respect. It does not trigger nothing from the > list above, but I still get the message during reboot > [ ... ] watchdog: watchdog0: watchdog did not stop! > ... with some small timeout. > The first obvious question - is there only one watchdog? Some watchdog drivers *are* autoloaded. Is there only one user of watchdog? systemd may use it too as example. > So after some additional testing, the situation is the following: > > - without any watchdog and without sbd package, the server reboots normally > - with "softdog" module loaded, I only get "watchdog did not stop message" at > reboot > - with "softdog" loaded, but unloaded with "ExecStop=...rmmod", reboot is > normal again > - same as above, but with "sbd" package loaded, I am getting "watchdog did > not stop message" again > - switching from "softdog" to "ipmi_watchdog" gets me to the original list of > problems > > It looks like the "sbd" is preventing the watchdog to close, so that watchdog > triggers always, even in the case of normal reboot. What am I missing here? While the only way I can reproduce it on my QEMU VM is "reboot -f" (without stopping all services), there is certainly a race condition in sbd.service. ExecStop=@bindir@/kill -TERM $MAINPID systemd will continue as soon as "kill" completes without waiting for sbd to actually stop. It means systemd may complete shutdown sequence before sbd had chance to react on signal and then simply kill it. Which leaves watchdog armed. For test purpose try to use script that loops until sbd is actually stopped for ExecStop. Note that systemd strongly recommends to use synchronous command for ExecStop (we may argue that this should be handled by service manager itself, but well ...). > > Zoran > > - Original Message - > From: "Andrei Borzenkov" > To: "users" > Sent: Friday, June 3, 2022 11:24:03 AM > Subject: Re: [ClusterLabs] normal reboot with active sbd does not work > > On 03.06.2022 11:18, Zoran Bošnjak wrote: >> Hi all, >> I would appreciate an advice about sbd fencing (without shared storage). >> >> I am using ubuntu 20.04., with default packages from the repository >> (pacemaker, corosync, fence-agents, ipmitool, pcs...). >> >> HW watchdog is present on servers. The first problem was to load/unload the >> watchdog module. For some reason the module is blacklisted on ubuntu, > > What makes you think so? > > bor@bor-Latitude-E5450:~$ lsb_release -d > > Description: Ubuntu 20.04.4 LTS > > bor@bor-Latitude-E5450:~$ modprobe -c | grep ipmi_watchdog > > bor@bor-Latitude-E5450:~$ > > > > > >> so I've created a service for this purpose. >> > > man modules-load.d > > >> --- file: /etc/systemd/system/watchdog.service >> [Unit] >> Description=Load watchdog timer module >> After=syslog.target >> > > Without any explicit dependencies stop will be attempted as soon as > possible. > >> [Service] >> Type=oneshot >> RemainAfterExit=yes >> ExecStart=/sbin/modprobe ipmi_watchdog >> ExecStop=/sbin/rmmod ipmi_watchdog >> > > Why on earth do you need to unload kernel driver when system reboots? > >> [Install] >> WantedBy=multi-user.target >> --- >> >> Is this a proper way to load watchdog module und
Re: [ClusterLabs] normal reboot with active sbd does not work
On Fri, Jun 3, 2022 at 3:51 PM Zoran Bošnjak wrote: > > Thanks for all your answers. Sorry, my mistake. The ipmi_watchdog is indeed > OK. I was first experimenting with "softdog", which is blacklisted. So the > reasonable question is how to properly start "softdog" on ubuntu. > > The reason to unload watchdog module (ipmi or softdog) is that there seems to > be a difference between normal reboot and watchdog reboot. > In case of ipmi watchdog timer reboot: > - the system hangs at the end of reboot cycle for some time > - restart seems to be harder (like power off/on cycle), BIOS runs more > diagnostics at startup > - it turns on HW diagnostic indication on the server front panel (dell > server) which stays on forever > - it logs the event to IDRAC, which is unnecessary, because it was not a > hardware event, but just a normal reboot > > In case of "sudo reboot" command, I would like to skip this... so the idea is > to fully stop the watchdog just before reboot. I am not sure how to do this > properly. > > The "softdog" is better in this respect. It does not trigger nothing from the > list above, but I still get the message during reboot > [ ... ] watchdog: watchdog0: watchdog did not stop! > ... with some small timeout. > > So after some additional testing, the situation is the following: > > - without any watchdog and without sbd package, the server reboots normally > - with "softdog" module loaded, I only get "watchdog did not stop message" at > reboot > - with "softdog" loaded, but unloaded with "ExecStop=...rmmod", reboot is > normal again > - same as above, but with "sbd" package loaded, I am getting "watchdog did > not stop message" again > - switching from "softdog" to "ipmi_watchdog" gets me to the original list of > problems > > It looks like the "sbd" is preventing the watchdog to close, so that watchdog > triggers always, even in the case of normal reboot. What am I missing here? sbd has the watchdog-device open and thus is preventing unloading the module. Without giving any instructions in your unit-file systemd will try to stop the unit immediately and thus fail. Have you tried [Unit] Before=sbd.service [Install] RequiredBy=sbd.service I would have expected that rebooting with the device disabled again after sbd shuts down should behave similarly as with the module being unloaded. You could check for something like 'nowayout' with the kernel module that would prevent disabling the watchdog once opened. Klaus > > Zoran > > - Original Message - > From: "Andrei Borzenkov" > To: "users" > Sent: Friday, June 3, 2022 11:24:03 AM > Subject: Re: [ClusterLabs] normal reboot with active sbd does not work > > On 03.06.2022 11:18, Zoran Bošnjak wrote: > > Hi all, > > I would appreciate an advice about sbd fencing (without shared storage). > > > > I am using ubuntu 20.04., with default packages from the repository > > (pacemaker, corosync, fence-agents, ipmitool, pcs...). > > > > HW watchdog is present on servers. The first problem was to load/unload the > > watchdog module. For some reason the module is blacklisted on ubuntu, > > What makes you think so? > > bor@bor-Latitude-E5450:~$ lsb_release -d > > Description:Ubuntu 20.04.4 LTS > > bor@bor-Latitude-E5450:~$ modprobe -c | grep ipmi_watchdog > > bor@bor-Latitude-E5450:~$ > > > > > > > so I've created a service for this purpose. > > > > man modules-load.d > > > > --- file: /etc/systemd/system/watchdog.service > > [Unit] > > Description=Load watchdog timer module > > After=syslog.target > > > > Without any explicit dependencies stop will be attempted as soon as > possible. > > > [Service] > > Type=oneshot > > RemainAfterExit=yes > > ExecStart=/sbin/modprobe ipmi_watchdog > > ExecStop=/sbin/rmmod ipmi_watchdog > > > > Why on earth do you need to unload kernel driver when system reboots? > > > [Install] > > WantedBy=multi-user.target > > --- > > > > Is this a proper way to load watchdog module under ubuntu? > > > > There is standard way to load non-autoloaded drivers on *any* systemd > based distribution. Which is modules-load.d. > > > Anyway, once the module is loaded, the /dev/watchdog (which is required by > > 'sbd') is present. > > Next, the 'sbd' is installed by > > > > sudo apt install sbd > > (followed by one reboot to get the sbd active) > > > > The configuration of the 'sbd' is d
Re: [ClusterLabs] normal reboot with active sbd does not work
Thanks for all your answers. Sorry, my mistake. The ipmi_watchdog is indeed OK. I was first experimenting with "softdog", which is blacklisted. So the reasonable question is how to properly start "softdog" on ubuntu. The reason to unload watchdog module (ipmi or softdog) is that there seems to be a difference between normal reboot and watchdog reboot. In case of ipmi watchdog timer reboot: - the system hangs at the end of reboot cycle for some time - restart seems to be harder (like power off/on cycle), BIOS runs more diagnostics at startup - it turns on HW diagnostic indication on the server front panel (dell server) which stays on forever - it logs the event to IDRAC, which is unnecessary, because it was not a hardware event, but just a normal reboot In case of "sudo reboot" command, I would like to skip this... so the idea is to fully stop the watchdog just before reboot. I am not sure how to do this properly. The "softdog" is better in this respect. It does not trigger nothing from the list above, but I still get the message during reboot [ ... ] watchdog: watchdog0: watchdog did not stop! ... with some small timeout. So after some additional testing, the situation is the following: - without any watchdog and without sbd package, the server reboots normally - with "softdog" module loaded, I only get "watchdog did not stop message" at reboot - with "softdog" loaded, but unloaded with "ExecStop=...rmmod", reboot is normal again - same as above, but with "sbd" package loaded, I am getting "watchdog did not stop message" again - switching from "softdog" to "ipmi_watchdog" gets me to the original list of problems It looks like the "sbd" is preventing the watchdog to close, so that watchdog triggers always, even in the case of normal reboot. What am I missing here? Zoran ----- Original Message - From: "Andrei Borzenkov" To: "users" Sent: Friday, June 3, 2022 11:24:03 AM Subject: Re: [ClusterLabs] normal reboot with active sbd does not work On 03.06.2022 11:18, Zoran Bošnjak wrote: > Hi all, > I would appreciate an advice about sbd fencing (without shared storage). > > I am using ubuntu 20.04., with default packages from the repository > (pacemaker, corosync, fence-agents, ipmitool, pcs...). > > HW watchdog is present on servers. The first problem was to load/unload the > watchdog module. For some reason the module is blacklisted on ubuntu, What makes you think so? bor@bor-Latitude-E5450:~$ lsb_release -d Description:Ubuntu 20.04.4 LTS bor@bor-Latitude-E5450:~$ modprobe -c | grep ipmi_watchdog bor@bor-Latitude-E5450:~$ > so I've created a service for this purpose. > man modules-load.d > --- file: /etc/systemd/system/watchdog.service > [Unit] > Description=Load watchdog timer module > After=syslog.target > Without any explicit dependencies stop will be attempted as soon as possible. > [Service] > Type=oneshot > RemainAfterExit=yes > ExecStart=/sbin/modprobe ipmi_watchdog > ExecStop=/sbin/rmmod ipmi_watchdog > Why on earth do you need to unload kernel driver when system reboots? > [Install] > WantedBy=multi-user.target > --- > > Is this a proper way to load watchdog module under ubuntu? > There is standard way to load non-autoloaded drivers on *any* systemd based distribution. Which is modules-load.d. > Anyway, once the module is loaded, the /dev/watchdog (which is required by > 'sbd') is present. > Next, the 'sbd' is installed by > > sudo apt install sbd > (followed by one reboot to get the sbd active) > > The configuration of the 'sbd' is default. The sbd reacts to network failure > as expected (reboots the server). However, when the 'sbd' is active, the > server won't reboot normally any more. For example from the command line > "sudo reboot", it gets stuck at the end of the reboot sequence. There is a > message on the console: > > ... reboot progress > [ OK ] Finished Reboot. > [ OK ] Reached target Reboot. > [ ... ] IPMI Watchdog: Unexpected close, not stopping watchdog! > [ ... ] IPMI Watchdog: Unexpected close, not stopping watchdog! > ... it gets stuck at this point > > After some long timeout, it looks like the watchdog timer expires and server > boots, but the failure indication remains on the front panel of the server. > If I uninstall the 'sbd' package, the "sudo reboot" works normally again. > > My question is: How do I configure the system, to have the 'sbd' function > present, but still be able to reboot the system normally. > As the first step - do not unload watchdog driver on shutdown. ___ Manage your subscription: https://lists.clusterlabs.org/mailman/listinfo/users ClusterLabs home: https://www.clusterlabs.org/ ___ Manage your subscription: https://lists.clusterlabs.org/mailman/listinfo/users ClusterLabs home: https://www.clusterlabs.org/
Re: [ClusterLabs] normal reboot with active sbd does not work
On 03.06.2022 11:18, Zoran Bošnjak wrote: > Hi all, > I would appreciate an advice about sbd fencing (without shared storage). > > I am using ubuntu 20.04., with default packages from the repository > (pacemaker, corosync, fence-agents, ipmitool, pcs...). > > HW watchdog is present on servers. The first problem was to load/unload the > watchdog module. For some reason the module is blacklisted on ubuntu, What makes you think so? bor@bor-Latitude-E5450:~$ lsb_release -d Description:Ubuntu 20.04.4 LTS bor@bor-Latitude-E5450:~$ modprobe -c | grep ipmi_watchdog bor@bor-Latitude-E5450:~$ > so I've created a service for this purpose. > man modules-load.d > --- file: /etc/systemd/system/watchdog.service > [Unit] > Description=Load watchdog timer module > After=syslog.target > Without any explicit dependencies stop will be attempted as soon as possible. > [Service] > Type=oneshot > RemainAfterExit=yes > ExecStart=/sbin/modprobe ipmi_watchdog > ExecStop=/sbin/rmmod ipmi_watchdog > Why on earth do you need to unload kernel driver when system reboots? > [Install] > WantedBy=multi-user.target > --- > > Is this a proper way to load watchdog module under ubuntu? > There is standard way to load non-autoloaded drivers on *any* systemd based distribution. Which is modules-load.d. > Anyway, once the module is loaded, the /dev/watchdog (which is required by > 'sbd') is present. > Next, the 'sbd' is installed by > > sudo apt install sbd > (followed by one reboot to get the sbd active) > > The configuration of the 'sbd' is default. The sbd reacts to network failure > as expected (reboots the server). However, when the 'sbd' is active, the > server won't reboot normally any more. For example from the command line > "sudo reboot", it gets stuck at the end of the reboot sequence. There is a > message on the console: > > ... reboot progress > [ OK ] Finished Reboot. > [ OK ] Reached target Reboot. > [ ... ] IPMI Watchdog: Unexpected close, not stopping watchdog! > [ ... ] IPMI Watchdog: Unexpected close, not stopping watchdog! > ... it gets stuck at this point > > After some long timeout, it looks like the watchdog timer expires and server > boots, but the failure indication remains on the front panel of the server. > If I uninstall the 'sbd' package, the "sudo reboot" works normally again. > > My question is: How do I configure the system, to have the 'sbd' function > present, but still be able to reboot the system normally. > As the first step - do not unload watchdog driver on shutdown. ___ Manage your subscription: https://lists.clusterlabs.org/mailman/listinfo/users ClusterLabs home: https://www.clusterlabs.org/
Re: [ClusterLabs] normal reboot with active sbd does not work
On Fri, Jun 3, 2022 at 11:03 AM Klaus Wenninger wrote: > > On Fri, Jun 3, 2022 at 10:19 AM Zoran Bošnjak wrote: > > > > Hi all, > > I would appreciate an advice about sbd fencing (without shared storage). > > > > I am using ubuntu 20.04., with default packages from the repository > > (pacemaker, corosync, fence-agents, ipmitool, pcs...). > > > > HW watchdog is present on servers. The first problem was to load/unload the > > watchdog module. For some reason the module is blacklisted on ubuntu, so > > I've created a service for this purpose. > > > > --- file: /etc/systemd/system/watchdog.service > > [Unit] > > Description=Load watchdog timer module > > After=syslog.target > > > > [Service] > > Type=oneshot > > RemainAfterExit=yes > > ExecStart=/sbin/modprobe ipmi_watchdog > > ExecStop=/sbin/rmmod ipmi_watchdog > > > > [Install] > > WantedBy=multi-user.target > > --- > > > > Is this a proper way to load watchdog module under ubuntu? > > > > Anyway, once the module is loaded, the /dev/watchdog (which is required by > > 'sbd') is present. > > Next, the 'sbd' is installed by > > > > sudo apt install sbd > > (followed by one reboot to get the sbd active) > > > > The configuration of the 'sbd' is default. The sbd reacts to network > > failure as expected (reboots the server). However, when the 'sbd' is > > active, the server won't reboot normally any more. For example from the > > command line "sudo reboot", it gets stuck at the end of the reboot > > sequence. There is a message on the console: > > > > ... reboot progress > > [ OK ] Finished Reboot. > > [ OK ] Reached target Reboot. > > [ ... ] IPMI Watchdog: Unexpected close, not stopping watchdog! > > [ ... ] IPMI Watchdog: Unexpected close, not stopping watchdog! > > ... it gets stuck at this point > > > > After some long timeout, it looks like the watchdog timer expires and > > server boots, but the failure indication remains on the front panel of the > > server. If I uninstall the 'sbd' package, the "sudo reboot" works normally > > again. > > > > My question is: How do I configure the system, to have the 'sbd' function > > present, but still be able to reboot the system normally. > > Loading modules - depending on distribution an version - should probably > rather > be done editing /etc/modules or putting some files under /etc/modprobe-d/. Of course that would require removing the driver from blacklist. Any reason why you didn't consider that? > Guess in your case stopping the unit won't work as the watchdog-device is > still opened by sbd. In general I don't see why the watchdog-module should > be unloaded upon shutdown. So as a first try you just might remove that part. > > Klaus > > > > > regards, > > Zoran > > ___ > > Manage your subscription: > > https://lists.clusterlabs.org/mailman/listinfo/users > > > > ClusterLabs home: https://www.clusterlabs.org/ > > ___ Manage your subscription: https://lists.clusterlabs.org/mailman/listinfo/users ClusterLabs home: https://www.clusterlabs.org/
Re: [ClusterLabs] normal reboot with active sbd does not work
On Fri, Jun 3, 2022 at 10:19 AM Zoran Bošnjak wrote: > > Hi all, > I would appreciate an advice about sbd fencing (without shared storage). > > I am using ubuntu 20.04., with default packages from the repository > (pacemaker, corosync, fence-agents, ipmitool, pcs...). > > HW watchdog is present on servers. The first problem was to load/unload the > watchdog module. For some reason the module is blacklisted on ubuntu, so I've > created a service for this purpose. > > --- file: /etc/systemd/system/watchdog.service > [Unit] > Description=Load watchdog timer module > After=syslog.target > > [Service] > Type=oneshot > RemainAfterExit=yes > ExecStart=/sbin/modprobe ipmi_watchdog > ExecStop=/sbin/rmmod ipmi_watchdog > > [Install] > WantedBy=multi-user.target > --- > > Is this a proper way to load watchdog module under ubuntu? > > Anyway, once the module is loaded, the /dev/watchdog (which is required by > 'sbd') is present. > Next, the 'sbd' is installed by > > sudo apt install sbd > (followed by one reboot to get the sbd active) > > The configuration of the 'sbd' is default. The sbd reacts to network failure > as expected (reboots the server). However, when the 'sbd' is active, the > server won't reboot normally any more. For example from the command line > "sudo reboot", it gets stuck at the end of the reboot sequence. There is a > message on the console: > > ... reboot progress > [ OK ] Finished Reboot. > [ OK ] Reached target Reboot. > [ ... ] IPMI Watchdog: Unexpected close, not stopping watchdog! > [ ... ] IPMI Watchdog: Unexpected close, not stopping watchdog! > ... it gets stuck at this point > > After some long timeout, it looks like the watchdog timer expires and server > boots, but the failure indication remains on the front panel of the server. > If I uninstall the 'sbd' package, the "sudo reboot" works normally again. > > My question is: How do I configure the system, to have the 'sbd' function > present, but still be able to reboot the system normally. Loading modules - depending on distribution an version - should probably rather be done editing /etc/modules or putting some files under /etc/modprobe-d/. Guess in your case stopping the unit won't work as the watchdog-device is still opened by sbd. In general I don't see why the watchdog-module should be unloaded upon shutdown. So as a first try you just might remove that part. Klaus > > regards, > Zoran > ___ > Manage your subscription: > https://lists.clusterlabs.org/mailman/listinfo/users > > ClusterLabs home: https://www.clusterlabs.org/ > ___ Manage your subscription: https://lists.clusterlabs.org/mailman/listinfo/users ClusterLabs home: https://www.clusterlabs.org/
[ClusterLabs] normal reboot with active sbd does not work
Hi all, I would appreciate an advice about sbd fencing (without shared storage). I am using ubuntu 20.04., with default packages from the repository (pacemaker, corosync, fence-agents, ipmitool, pcs...). HW watchdog is present on servers. The first problem was to load/unload the watchdog module. For some reason the module is blacklisted on ubuntu, so I've created a service for this purpose. --- file: /etc/systemd/system/watchdog.service [Unit] Description=Load watchdog timer module After=syslog.target [Service] Type=oneshot RemainAfterExit=yes ExecStart=/sbin/modprobe ipmi_watchdog ExecStop=/sbin/rmmod ipmi_watchdog [Install] WantedBy=multi-user.target --- Is this a proper way to load watchdog module under ubuntu? Anyway, once the module is loaded, the /dev/watchdog (which is required by 'sbd') is present. Next, the 'sbd' is installed by sudo apt install sbd (followed by one reboot to get the sbd active) The configuration of the 'sbd' is default. The sbd reacts to network failure as expected (reboots the server). However, when the 'sbd' is active, the server won't reboot normally any more. For example from the command line "sudo reboot", it gets stuck at the end of the reboot sequence. There is a message on the console: ... reboot progress [ OK ] Finished Reboot. [ OK ] Reached target Reboot. [ ... ] IPMI Watchdog: Unexpected close, not stopping watchdog! [ ... ] IPMI Watchdog: Unexpected close, not stopping watchdog! ... it gets stuck at this point After some long timeout, it looks like the watchdog timer expires and server boots, but the failure indication remains on the front panel of the server. If I uninstall the 'sbd' package, the "sudo reboot" works normally again. My question is: How do I configure the system, to have the 'sbd' function present, but still be able to reboot the system normally. regards, Zoran ___ Manage your subscription: https://lists.clusterlabs.org/mailman/listinfo/users ClusterLabs home: https://www.clusterlabs.org/
