On Thu, Oct 12, 2017 at 3:10 AM, Jonathan Frederickson
wrote:
>> if it's ok with you the priority will be on people with linux kernel
>> / u-boot (etc.) experience
>
> Understandable, that seems to be what you need the most at this point.
that and some extra cash.
> if it's ok with you the priority will be on people with linux kernel
> / u-boot (etc.) experience
Understandable, that seems to be what you need the most at this point.
> well, "sysadmin" to me says "clearly capable of trusting and
> following written instructions to the letter" which
https://ez.analog.com/docs/DOC-11303
Each TMDS signal shall have single ended impedance of 50 Ω ± 10%.
Each TMDS pair shall have differential impedance of 100 Ω ± 5%.
whoops :) 89 ohm... 50 ohm. 89 ohm... 50 ohm. oops... :)
___
arm-netbook
On Thu, Oct 12, 2017 at 1:41 AM, Jonathan Frederickson
wrote:
> I'm interested as well, though I likewise don't have the low-level
> software experience that would likely be required.
if it's ok with you the priority will be on people with linux kernel
/ u-boot (etc.)
I'm interested as well, though I likewise don't have the low-level
software experience that would likely be required. I'm a Linux
sysadmin, so Linux I can do, but ARM kernel/boot stuff is a bit out of
my depth thus far. That said, I do have access to a laser cutter and a
(small) 3D printer, so I
---
crowd-funded eco-conscious hardware: https://www.crowdsupply.com/eoma68
On Wed, Oct 11, 2017 at 6:18 PM, Richard Wilbur
wrote:
> Afterthought: If PADS does give impedance values, please include the
> values for each of the HDMI differential traces and a URL to
---
crowd-funded eco-conscious hardware: https://www.crowdsupply.com/eoma68
On Wed, Oct 11, 2017 at 5:58 PM, Richard Wilbur
wrote:
> Your change to TX1 definitely looks like an improvement.
>
> In order to make a determination on the best course of action
> regarding
On Thu, Oct 12, 2017 at 12:34 AM, Tor, the Marqueteur
wrote:
>> well the microdesktop has to go out at the same time, and that's
>> been ready for months. it's a little limiting to use the card on
>> its own (no access to UART boot messages for example) and
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
On 10/11/2017 12:24 PM, Luke Kenneth Casson Leighton wrote:
> On Wed, Oct 11, 2017 at 10:40 PM, Tor, the Marqueteur
> wrote:
>
>>> thx tor. btw i still need to send you a micro-desktop and some
>>> of the
On Wed, Oct 11, 2017 at 10:40 PM, Tor, the Marqueteur
wrote:
>> thx tor. btw i still need to send you a micro-desktop and some of
>> the laser-cut casework i have here, so you can design and test the
>> wooden corners.
>>
> Sooner or later, yes. I haven't
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
On 10/10/2017 10:07 PM, Luke Kenneth Casson Leighton wrote:
>
> On Wed, Oct 11, 2017 at 8:27 AM, Tor, the Marqueteur
> wrote:
>>
>> I'm interested, and I should be able to cover the costs. ...
> thx tor. btw i
Afterthought: If PADS does give impedance values, please include the
values for each of the HDMI differential traces and a URL to images of
the top and bottom layers of that layout.
That way I'll be able to make recommendations and markup the picture
to hopefully make everything clear.
Thanks,
Your change to TX1 definitely looks like an improvement.
In order to make a determination on the best course of action
regarding the keepout at the connector end and whether to recommend
some type of taper I still have a burning question:
What does PADS currently give as the impedance of the
---
crowd-funded eco-conscious hardware: https://www.crowdsupply.com/eoma68
On Wed, Oct 11, 2017 at 8:27 AM, Tor, the Marqueteur
wrote:
> -BEGIN PGP SIGNED MESSAGE-
> Hash: SHA1
>
> I'm interested, and I should be able to cover the costs. That said, I
>
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
I'm interested, and I should be able to cover the costs. That said, I
don't have sofware dev skills, so except perhaps for a micro-desktop
board (depends on final design of the micro-desktop), there's not much
advantage to the project in my having
15 matches
Mail list logo