I've got some Asterisk 11 (I could 'upgrade' if needed) hosts using meetme
and I'd like to switch to confbridge to service more callers.
Can anyone reply with their experience along the lines of 'using meetme I
was only getting x callers per server but with confbridge I now get y
callers per
I am using 11.17.0 - and MulticastRTP. Doesnt seem to work with
polycom phones as other devices receive my multicast just fine.
Is there something special to do to get multicast working with polycom
phones?
(other than enable multicast on the actual phone).
Didn't see if anyone had
I hesitate to promote the name here since this is non-commercial
discussion...
but Polycom...
Polycom phones...
If mentioning Polycom is OK, I think mentioning a possible commercial
solution is OK.
In that case, the product in question is the Algo 8180 SIP Audio Alerter.
I will
On Mon, 13 Apr 2015, Kevin Larsen wrote:
I hesitate to promote the name here since this is non-commercial
discussion...
but Polycom...
Polycom phones...
If mentioning Polycom is OK, I think mentioning a possible commercial
solution is OK.
--
Thanks in advance,
Read the config.log file to know for which dependency it failed.
On 13-Apr-2015 2:08 PM, akhilesh chand omakhileshch...@gmail.com wrote:
yes I called
On Mon, Apr 13, 2015 at 1:27 PM, jg webaccounts...@jgoettgens.de wrote:
I'm not able to install asterisk whenever I hit make command I get
I'm not able to install asterisk whenever I hit make command I get below error:
make[1]: *** No rule to make target `../main/modules.link', needed by
`asterisk'. Stop.
make: *** [main] Error 2
Just guessing. Did you call ./configure?
jg
--
Hi folks,
I'm not able to install asterisk whenever I hit make command I get below
error:
make[1]: *** No rule to make target `../main/modules.link', needed by
`asterisk'. Stop.
make: *** [main] Error 2
Regards
Akhilesh
--
yes I called
On Mon, Apr 13, 2015 at 1:27 PM, jg webaccounts...@jgoettgens.de wrote:
I'm not able to install asterisk whenever I hit make command I get below
error:
make[1]: *** No rule to make target `../main/modules.link', needed by
`asterisk'. Stop.
make: *** [main] Error 2
Just
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
On 04/13/2015 03:40 PM, akhilesh chand wrote:
Hi folks,
I'm not able to install asterisk whenever I hit make command I get
below error:
make[1]: *** No rule to make target `../main/modules.link', needed
by `asterisk'. Stop. make: ***
Hi Akhilesh,
Here is another fix,
getting the error, that: make[1]: *** No rule to make target
`../main/modules.link’, needed by `asterisk’. Stop. make: *** [main] Error
2 when compile asterisk
To get around this, just delete following line in file makeopts.embed_rules
yes modules.link is existing in pbx/modules.link.
On Mon, Apr 13, 2015 at 2:35 PM, Guenther Boelter gboel...@gmail.com
wrote:
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
On 04/13/2015 03:40 PM, akhilesh chand wrote:
Hi folks,
I'm not able to install asterisk whenever I hit make
The below error
make[1]: *** No rule to make target `../main/modules.link', needed by
`asterisk'. Stop.
make: *** [main] Error 2
may be due problem in settings/configuration, double check these and try
again
On Mon, Apr 13, 2015 at 1:10 PM, akhilesh chand omakhileshch...@gmail.com
wrote:
Hi
Hi all
I've got a setup where I use a Sangoma PRI card driven via Sangoma WanPipe
to connect to a legacy Samsung PABX (I'm not sure which model) form Asterisk
1.8.11.0.
The reason is the customer has a large installed base of Samsung phones
physically connected to it and on each users desk. They
I am using 11.17.0 - and MulticastRTP. Doesnt seem to work with
polycom phones as other devices receive my multicast just fine.
Is there something special to do to get multicast working with polycom
phones?
(other than enable multicast on the actual phone).
Thanks
Jerry
--
Did you do make menuselect and saved the options ?
Mitul
On 13-Apr-2015 5:43 PM, ajahar mohd azhar5...@gmail.com wrote:
Hi Akhilesh,
Here is another fix,
getting the error, that: make[1]: *** No rule to make target
`../main/modules.link’, needed by `asterisk’. Stop. make: *** [main] Error
Using asterisk 11.16.0 I am unable to retrieve any voicemail with a video
attachment while using any video phone. This does work in my 1.8.23.1
installation. The file is skipped with the ast_streamfile error (and moved to
OLD), and the prompts following that message display the ast_best_codec
BABY appears to be a global variable in your example.
In your CLI output testcarrier is a peer, It's not a variable at all.
The context field for your peer testcarrier is where incoming calls from
testcarrirer will be routed to.
Here is some example dialplan showing how you can use one context
17 matches
Mail list logo