Hi.
Im trying to get a Beronet QuadBRI card work with
bristuff drivers. Though qozap module loads right, all card spans are in
deactivated status. Im quite sure my configuration is correct and using
a single BRI card instead of the quadBRI the status is active and I can place
and receive
Calling any unreachable mobile from Fastweb or Telecom PSTN I don't get
any courtesy message. The same happens when calling an inexistent
number.
I'm configuring two PBX's, connected to two different phone lines, both
behave this way.
Perhaps there's some missing zapata parameter?
Regards,
_fangi_
I was wrong.
The problem was with chan_sccp library and was solved downgrading from version
20060207 to 20060204.
_fangi_
-Messaggio originale-
Da: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Per conto di Francesco Angi
Inviato: venerdì 24 febbraio 2006 10.00
A: Asterisk Users Mailing
Hi everybody.
Just noticed that when calling a mobile phone, Asterisk
doesnt bridge the voice message by telco if mobile is unreachable, but
keeps on ringing till it receives a hangup signal. I think this is due to the
fact that the message is played without the call has been answered,
Solved the problem downgrading zaptel 1.2.4 to 1.2.3.
Mantaining the same configurations now everything works fine.
Regards,
_fangi_
-Messaggio originale-
Da: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Per conto di Francesco Angi
Inviato: martedì 21 febbraio 2006 14.35
A: Asterisk
That's exactly what I was looking for.
By the way, I discovered Local channels to fork into dialplan.
I also discovered that roundrobin policy does not work as I expected, but
that's another story.
Thanks for help,
_fangi_
-Messaggio originale-
Da: [EMAIL PROTECTED] [mailto:[EMAIL
Hi everybody,
I'm facing a strange problem after upgrading Asterisk from 1.0.9 to
1.2.4.
Sometimes, when receiving an incoming call from pstn, although my sip
phones ring correctly (I've got both softphones and hardware phones),
noone can pick up the call. Asterisk CLI shows me that the phones are
Hi folks,
need some help on queue behaviour.
What Im trying to do is accepting a call from
pstn, put it into a queue, while callee is waiting contact some numbers till
one responds, then bridge the two calls.
What I cant manage is jump to next dialplan
command soon after callee enters
Hi all.
Ive got Asterisk CVS Head running on Fedora
Core 3. It has been running for 4 months with no particular problem. Recently I
tried to enable presence. On dialplan I added hint extensions for all my SIP
users and on my Eyebeam clients (v. 1.1 3008q) I set Peer-to-Peer presence
mode.
Francesco Angi ha scritto:
Two
simple questions about Cisco 7905 on Asterisk using chan_sccp.
1) using both sccp firmware 5.0 and 6.1 I
cannot put a call in hold,
because there's no Hold Button at all! Is
there a way to configure
The 7905 has
an hard button for the hold stuff
Hi all.
Two simple questions about Cisco 7905 on Asterisk using chan_sccp.
1) using both sccp firmware 5.0 and 6.1 I cannot put a call in hold,
because there's no Hold Button at all! Is there a way to configure
buttons? Perhaps through XML?
2) How can I configure Message button to dial my
Hi folks,
I've already searched the mailing list but no one else
seems to have my same problem.
I'm using Asterisk with the following configuration:
Fedora Core 4 (but I also tried Fedora 3)
1 Digium TE110P
1 TDM40B
1 HFC-S 'Cologne'
bristuff 0.2.0-RC8o (zaptel 1.0.9.2)
I
Same problem with debian sarge on a dell and asterisk 1.0.7 from
packages, unloading the module freezes the system, (rebooting the
machine worked right), I installed zaptel 1.2beta and it seems to
work,
but I haven't really tested it, only loaded/unloaded/loaded and
placed a
couple of
13 matches
Mail list logo
