-users] PRI issue its BUSY
From:
asterisk-users-boun...@lists.digium.com
[mailto:asterisk-users-boun...@lists.digium.com] On Behalf Of satish patel
Sent: Monday, June 06, 2011 8:20
PM
To: asterisk-users
Subject: [asterisk-users] PRI
issue its BUSY
Hi all,
I just
To: asterisk-users@lists.digium.com
Date: Mon, 6 Jun 2011 20:24:06 -0500
Subject: Re: [asterisk-users] PRI issue its BUSY
From:
asterisk-users-boun...@lists.digium.com
[mailto:asterisk-users-boun...@lists.digium.com] On Behalf Of satish patel
Sent: Monday, June 06, 2011 8:20
PM
: [asterisk-users] PRI issue its BUSY
sometime i am getting Span 1: Channel 0/23 got hangup request, cause 16 but my
call doesn't get completed
== Primary D-Channel on span 1 up
-- Restart requested on entire span 1
== Using SIP RTP CoS mark 5
-- Executing [7076941815@from-sip:1
hello everyone,
Last week I installed asterisk 1.2.24 with digium TE220B card. I have a
problem with our PRI and Asterisk: the call be interrupted.It happens either
PSTN-to-SIP or SIP-to-SIP,almost every call.
After spending several days searching on internet, I found a lot of
discussion
On 06/23/06 01:22 Andy Brezinsky said the following:
Protocol Discriminator: Q.931 (8) len=47
Call Ref: len= 2 (reference 15996/0x3E7C) (Originator)
Message type: SETUP (5)
Protocol Discriminator: Q.931 (8) len=10
Call Ref: len= 2 (reference 48764/0xBE7C) (Terminator)
Message
Hey all. We have a DS3 circuit with GBLX split off into 7 systems with
a 4 port sangoma card (A104D) in the first 2 systems, and digium T410P
cards in the other 5. GBLX numbers their spans from 0 to 3 instead of
1-4 and we have a NFAS configuration with the d-channel on chan 96. All
of our
Andy Brezinsky wrote:
Hey all. We have a DS3 circuit with GBLX split off into 7 systems
with a 4 port sangoma card (A104D) in the first 2 systems, and digium
T410P cards in the other 5. GBLX numbers their spans from 0 to 3
instead of 1-4 and we have a NFAS configuration with the d-channel on
Terence Burnard wrote:
# cat /etc/zaptel.conf
span=1,0,0,esf,b8zs
bchan=1-23
dchan=24
loadzone=us
defaultzone=us
I don't know if this will fix your problem, but the span line should read:
span=1,1,0,esf,b8zs
You get your timing from the telco.
Doug
--
Ben Franklin quote:
Those who
On Monday 01 May 2006 01:42, Terence Burnard wrote:
Module Size Used by
wcusb 21760 0
wctdm 36512 0
wcfxo 13408 0
wcte11xp 24896 0
wct1xxp16544 0
wct4xxp97664 24
tor2
Andrew Kohlsmith wrote:
First of all, don't load every Asterisk module under the sun. Load the
modules for the hardware you have, and if you're using something like [EMAIL
PROTECTED]
which loads everything, edit your /etc/modules.conf to alias the ones you do
NOT have to 'off' to
On Monday 01 May 2006 07:27, Kevin P. Fleming wrote:
I believe you mean _Zaptel_ module, not _Asterisk_ module, in this case :-)
Ahh yes, you are correct. Place blame where due. :-)
-A.
___
--Bandwidth and Colocation provided by Easynews.com --
Hi,
I am about to pull my hair out after trying to get our PRI up and working.
We are switching from a Cisco gateway to an Asterisk box which provides
the 23 phone lines for our office. So, because the Cisco gateway is
working I can assume I have all the settings right (b8zs, esf, dms100,
etc)
Hi,
I recompiled asterisk today from CVS and Ive
been having a number of problems, Ive read the deadlock page on the wiki
and some of it sounds like that, however, the latest issue were having
it that sometimes Asterisk doesnt seem to know the PRI channel has
dropped, and assumes its
-Users] PRI issue
Hi,
I recompiled asterisk today from CVS and I've been having a number of
problems, I've read the deadlock page on the wiki and some of it sounds
like that, however, the latest issue we're having it that sometimes
Asterisk doesn't seem to know the PRI channel has dropped, and assumes
Users Mailing List - Non-Commercial Discussion
Subject: RE: [Asterisk-Users] PRI issue
Ben,
I ran into a similar issue on the 8/31 cvs, except it was backwards.
Outbound calls would report a busy on the channel selected, yet a few
minutes later the channel would be used for an inbound call. I
15 matches
Mail list logo
